Kenmore Pro 66514703N510 dishwasher Parts

On Kenmore Pro dishwasher model 66514703N510, the model number is printed on the rating label located just inside the dishwasher door, typically along the left-hand side of the tub opening. The same label usually lists the serial number.

Where to look (fast checklist)

• Open the dishwasher door fully.
• Look along the inner edge of the tub opening (not the outer decorative door panel).
• Check the left-hand side first.
• Find a sticker or metal tag labeled Model and Serial.
• Write the model number exactly as shown (letters and numbers).

What the label looks like

Most Kenmore dishwashers use a small rating label that includes key identification and electrical info.

Label item	What it’s used for	Why it matters
Model number	Parts lookup and compatibility	Ensures the right rack parts, pumps, and controls fit
Serial number	Production date and service reference	Helps match revisions and service bulletins
Electrical ratings	Installation and troubleshooting	Confirms correct power requirements

Why it matters

Even small model-number differences can change which parts fit your dishwasher, including common replacements like the dishwasher door latch WPW10653840 or the heating element assembly W10703867. Using the exact model number prevents ordering the wrong part and avoids repeat repairs.

If the label is hard to read

• Wipe the label gently with a damp cloth and mild soap; dry it.
• Use a flashlight and take a close-up photo to zoom in.
• If the label is damaged, check your purchase paperwork or the Use and Care section in the 66514703N510 owner's manual.

Last updated: January 2026

Common problems we see with the Kenmore Pro dishwasher model 66514703N510 include not starting, poor drying, detergent not dispensing, long cycle times, and draining issues. Many of these come down to door-latch problems, loading interference, hard-water buildup, or a restricted drain path; the troubleshooting chart in the 66514703N510 owner's manual walks through the fastest checks.

Most common symptoms (and what they usually point to)

• Dishwasher does not run: door not fully closed/latched, Start/Resume needs to be pressed again, power issue (breaker/fuse)
• Detergent remains in dispenser or tablet on tub bottom: dispenser blocked by dishes, poor water circulation from loading interference
• Cycle runs too long: normal pauses during the cycle, incoming water not hot enough
• Not drying: rinse aid missing, water temperature too low (typical target is 120°F)
• Water remains in tub / will not drain: kinked drain hose, disposer knockout plug not removed, food blockage in drain/disposer
• Cloudy or spotted dishes: hard water, low rinse aid, detergent amount needs adjustment

Quick checks we recommend first

1. Confirm the door is fully closed and latched, then press START/RESUME.
2. Check for loading interference (large casserole dishes can prevent proper door closure or spray action).
3. Verify power at the dishwasher; reset the house breaker if needed.
4. Inspect the drain path: look for kinks and clogs; confirm the disposer inlet knockout plug is removed.
5. Address hard water: clean filters monthly, use rinse aid, and run a dishwasher cleaner monthly.

Parts that commonly solve these issues

Symptom	Part to inspect/replace	What it affects
Won’t start or stops mid-cycle	Dishwasher door latch WPW10653840	Confirms the door is closed so the control will run
Won’t drain / standing water	Dishwasher drain pump WPW10531320	Pumps water out through the drain hose
Poor drying / odd heating behavior	Element assembly W10703867	Heats water and supports drying performance

Why it matters

Catching simple causes early (door latch engagement, loading interference, rinse aid, and drain restrictions) prevents repeat wash failures, reduces odor and residue, and helps protect the pump, motor, and sump from strain.

Last updated: January 2026

The Kenmore Pro dishwasher model 66514703N510 is designed to fit a standard built-in dishwasher opening; most installations use an opening about 24 inches deep (not counting handle) and 34 to 34 1/2 inches high, with height adjusted using the leveling legs and wheel positions. See the 66514703N510 installation guide for the cabinet-opening chart and clearances.

Typical fit and what to measure

Measure the cabinet opening before ordering parts or scheduling installation.

• Opening height: measure from the underside of the countertop (lowest point) to the floor (highest point)
• Opening width: most built-in dishwashers are about 24 inches wide
• Opening depth: plan for about 24 inches of depth, plus any handle projection
• Toe-kick clearance: confirm your toe-kick height and any trim interference
• Protrusions: check for screws, brackets, or pipes that block the dishwasher from sliding in

Height adjustment range (from the install guide)

The installation instructions include a height adjustment chart showing how wheel position and front-leg height are set to match the cabinet opening.

Cabinet opening height	What typically changes	What it affects
About 33 1/2 in.	Wheels may be removed; insulation blanket may be cut/removed	Helps fit shorter openings but makes sliding the unit harder
About 34 to 34 1/2 in.	Wheels and leveling legs adjusted	Most common built-in fit range

Why it matters

Correct sizing prevents installation problems like a dishwasher that will not slide fully into the opening, a door that rubs the toe kick, or hoses and wiring that get pinched near the motor or legs.

If you are replacing installation items during a re-fit, using a new drain hose is standard practice; the dishwasher drain hose WPW10545278 is one option listed for this model.

Last updated: January 2026

On a Kenmore dishwasher, error 22 (often shown as E22) points to a drainage or filtering problem, most commonly a blocked filter area that is restricting water flow. On model 66514703N510, start by cleaning the filter and checking for standing water in the tub per the 66514703N510 owner's manual.

What to do first (quick fixes)

• Cancel the cycle and let the unit stop completely.
• Remove the lower rack and clear any visible debris near the sump area.
• Clean the filter and the area around it (food, labels, glass fragments).
• Verify the door is fully closed and latched before restarting.
• Start the shortest cycle and check after about 2 minutes that water is present in the bottom of the tub.

If water is not draining

A blocked drain path can trigger the same symptoms as a “filter blocked” condition.

• Check the sink drain and/or disposer inlet for a clog.
• If your setup uses an air gap, clean the air gap cap and passage.
• Inspect the drain hose routing for kinks or a low loop issue.
• If the dishwasher hums but does not pump out, the drain pump may be jammed or failing.

Common parts related to draining

Symptom	Most likely area	Example part for 66514703N510
Water remains in tub	Drain pump or blockage	Dishwasher drain pump WPW10531320
Slow drain or intermittent drain	Drain hose routing/clog	Drain hose (inspect for kinks/clogs)

Why it matters

A restricted filter or drain path reduces wash performance and can leave dirty water in the tub. Clearing the filter and confirming proper draining helps protect the circulation system and keeps cycles running normally.

Last updated: January 2026