What size is Kenmore refrigerator model 79579783902?
Kenmore Elite refrigerator model 79579783902 is a bottom-freezer design; the exact exterior dimensions (width, depth, height) vary by configuration and are listed in the product specifications section of the 79579783902 owner's manual. Most 33-inch-class bottom-freezer refrigerators are roughly 33 inches wide and about 68 inches tall.
How to confirm the exact size for model 79579783902
Use these quick checks so you measure the right points for your kitchen opening:
- Check the dimensions and clearance requirements in the 79579783902 owner's manual
- Measure width at the widest point (often the hinge side, not just the cabinet)
- Measure height from floor to the top hinge cover area
- Measure depth two ways: cabinet only and to the front of the handles
- Add clearance for door swing, leveling, and airflow behind the unit
Typical size ranges (helpful for planning)
These ranges are common for Kenmore bottom-mount units in this class:
| Measurement | Typical range | What can change it |
|---|---|---|
| Width | 32 3/4 to 33 inches | hinge caps, trim |
| Height | 67 to 70 inches | leveling legs, hinge cover |
| Depth | 30 to 34 inches | handles, door curvature |
Why it matters
Getting the size right prevents installation problems like doors hitting cabinets, drawers not opening fully, and poor airflow that can lead to warm temperatures and longer compressor run times.
Measuring tips before you buy parts or move the refrigerator
- Remove items from the top and sides so you can measure accurately
- Measure the opening in at least 3 spots (top, middle, bottom)
- Plan for a little extra height because the front is typically leveled slightly higher than the back
Last updated: January 2026
What does DH mean on Kenmore Elite refrigerator?
On Kenmore Elite refrigerator model 79579783902, DH commonly indicates a defrost heating problem (the refrigerator is not sensing normal temperature rise during the defrost cycle). This can lead to frost buildup, warm temperatures, and reduced airflow if it is not corrected.
What to check first (safe, quick steps)
- Power reset: unplug the refrigerator (or switch off the breaker) for 5 minutes, then restore power.
- Confirm doors fully close and seals are making contact all the way around.
- Listen for the evaporator fan; airflow problems can mimic defrost issues.
- Check for heavy frost on the freezer back panel (a strong sign of a defrost system problem).
- If the display also shows OFF, make sure the unit is not in Demo mode (cooling disabled).
Likely causes of a DH/defrost heat issue
A DH-related defrost problem is usually tied to one of these components:
| What can fail | What you may notice | Related part examples for this model |
|---|---|---|
| Defrost heater | Frost builds up, freezer warms over time | Lg refrigerator defrost heater 5300JK1005D |
| Temperature sensing (thermistor/sensor) | Erratic temps, defrost not ending correctly | Refrigerator temperature sensor and cover ACQ73244001 |
| Airflow (evaporator fan) | Warm fridge section, weak airflow | Lg refrigerator evaporator fan motor 4681JB1027C |
Why it matters
When the defrost system is not heating correctly, ice can block the evaporator and air passages. That forces the compressor to run longer, can cause temperature swings, and may eventually stop cooling well in the refrigerator section.
Where to find model-specific troubleshooting steps
Use the troubleshooting section in the 79579783902 owner's manual to match the display message and symptoms (frost pattern, fan noise, temperature changes) to the correct repair path before replacing parts.
Last updated: January 2026
What are the common problems with Kenmore Elite refrigerators?
Common problems on the Kenmore Elite 79579783902 bottom-mount refrigerator include weak or warm cooling, frost buildup in the freezer, water leaks, and unusual noises. Most issues trace back to airflow restrictions (dirty condenser coils or a failed fan), door sealing problems, or a defrost and drain issue; our 79579783902 owner's manual troubleshooting section helps match symptoms to the right fix.
Most common symptoms and what usually causes them
- Not cooling or warm temperatures: dirty condenser coils, blocked air vents, or a failed evaporator fan motor
- Freezer frost or ice crystals on food: door not closing fully, gasket not sealing, frequent door openings
- Water puddles or leaks: clogged/iced drain system, cracked drain tube, loose water line connections
- Noisy operation (rattling, vibration, long run times): unit not level, items vibrating, warm room temps, frequent door openings
- Ice maker or dispenser issues: water supply restriction, inlet valve problem, dispenser door/auger issues
Quick checks we recommend first (no parts guessing)
- Confirm temperature settings and wait 24 hours between adjustments (the manual recommends waiting 24 hours before re-checking).
- Check door closing and gasket contact; warm, humid air leaks cause frost and poor cooling.
- Clean condenser coils (coil buildup is a top cause of warm temps and long run times).
- Listen for fan noise from the freezer area; a failed evaporator fan often causes warm refrigerator temps.
- Level the refrigerator if you hear vibration or rattling.
Parts that commonly solve these problems on model 79579783902
| Symptom | Common part involved | What it affects |
|---|---|---|
| Lights stay off or fan behavior changes when door moves | Refrigerator door switch 6600JB1010A | Door sensing for lights and some fan logic |
| Leaking inside or under unit | Refrigerator drain tube 5251JA3003D | Defrost water routing to drain pan |
| Frost, sweating, or poor sealing | Refrigerator door gasket MDS64172919 | Prevents warm air leaks into freezer |
| Warm temps with weak airflow | Lg refrigerator evaporator fan motor 4681JB1027C | Circulates cold air through compartments |
| No ice or slow water flow at dispenser | Refrigerator water inlet valve MJX41178908 | Controls water flow to ice maker/dispenser |
Why it matters
Cooling, frost, and leak complaints usually share one root cause: airflow and moisture control. A small air leak at the gasket or a dirty condenser coil can force the compressor to run longer, create frost, and reduce ice production.
Related DIY help
Last updated: January 2026





