Frigidaire FFID2423RS2A dishwasher Parts

To clear an error code on your Frigidaire FFID2423RS2A dishwasher, we reset the control by canceling the current cycle and restoring power if needed. Start with a Cancel (drain) reset, then correct the underlying issue (drain, fill, heat, or door latch) so the code does not return.

Try these in order; stop once the dishwasher responds normally.

• Cancel and drain reset: Press START/CANCEL; the dishwasher runs about a 90-second drain, then you can select a new cycle. See the FFID2423RS2A owner's manual.
• Power reset: Turn the dishwasher off at the breaker (or unplug if accessible) for 5 to 10 minutes, then restore power.
• Door reset: Open the door, wait 10 seconds, close it firmly, then start a cycle.
• Control lock check: If buttons do not respond, unlock the controls by pressing AIR DRY for about 8 seconds with the door open (lock indicator light turns off). See the FFID2423RS2A owner's manual.

Clearing the code is only step one; these checks prevent repeat errors.

• Not draining: Clean the filter area, check the sink/disposer connection, and inspect the drain hose for kinks or a blocked high loop. If the pump is noisy or not moving water, the drain pump a A00126401 is a common fix.
• Not filling: Confirm the water shutoff valve is fully open and the inlet screen is not clogged; a failed dishwasher water inlet valve 807047901 can also cause fill problems.
• Not drying or heating issues: Use heated dry options as desired; if heating performance is poor, the Frigidaire dishwasher heating element 154825001 is a key component.
• Door not starting cycle: Make sure the door closes and latches fully and nothing is interfering with the racks.

An error code is the dishwasher’s way of stopping to prevent poor cleaning, standing water, or overheating. Resetting gets you running again, but correcting the drain, fill, or heat problem is what keeps the FFID2423RS2A reliable.

Last updated: January 2026

You can find the model number for your Frigidaire dishwasher on the rating label; on most units like the FFID2423RS2A, it is located on the inside edge of the door or on the door frame when you open the door.

• Open the dishwasher door fully
• Check the top edge of the inner door
• Check the left or right side of the door frame (tub opening)
• Look for a sticker or metal plate labeled Model and Serial
• Wipe the area clean; soap film can hide the print

The rating label usually includes:

• Model number (example: FFID2423RS2A)
• Serial number
• Electrical ratings (volts/amps)
• Sometimes a barcode

Using the exact model number ensures the parts you choose match your dishwasher’s configuration. For example, components like the dishwasher electronic control board 5304504655 can vary by model revision, so the rating label is the best reference.

For a diagram of label locations and model identification tips, check the installation guide.

Last updated: March 2026

The average lifespan of a Frigidaire FFID2423RS2A dishwasher is 10 years with normal use and basic maintenance (cleaning filters, using the right detergent, and keeping spray arms clear). Replacing wear parts on time helps you reach that typical service life.

• Water quality (hard water speeds up mineral buildup)
• How often you run it (daily use wears pumps, seals, and racks faster)
• Loading habits (blocked spray arms reduce cleaning and strain the pump)
• Heat and drying performance (heater and wiring see more stress)
• Leak prevention (door seal condition and proper leveling)

If cleaning or drying declines, these are frequent culprits on many dishwashers and are available for this model:

Knowing the 10-year average helps you decide whether to maintain, repair, or refresh key components like the pump, heater, or door seal before a small issue turns into poor cleaning, standing water, or leaks.

For model-specific care and cleaning intervals, follow the maintenance guidance in the owner's manual.

Last updated: March 2026