Installation guide
Owner’s manual
Error Codes
How much does it cost to replace a heating element in a Frigidaire dryer?
For a Frigidaire dryer like model FEQ332ES0, heating element replacement typically costs about $200 to $400 total (part plus labor). If you do it yourself, you usually pay just the part cost, and this model’s heating element assembly is commonly the main expense.
Costs vary by location and service call minimums, but this is the usual range for an electric dryer heating repair.
- Heating element assembly (part): often $80 to $200
- Labor: often $100 to $200
- Service call/diagnostic fee: often $0 to $100 (sometimes waived with repair)
- Total typical installed price: $200 to $400
| Scenario | What you pay for | Typical total |
|---|---|---|
| DIY replacement | Part only | $80 to $200 |
| Pro replacement | Part + labor + possible service call | $200 to $400 |
On FEQ332ES0, “no heat” or weak heat is not always the element itself. These parts are often checked or replaced together during diagnosis.
- Frigidaire dryer heating element assembly 131553900
- Dryer thermal limiter 134120900 (opens if the dryer overheats)
- High-limit thermostat (opens if temperature gets too high)
- Venting components (restricted airflow can cause repeat failures)
A new heating element can fail early if airflow is restricted. Your installation instructions call out lint buildup and duct restrictions as a fire hazard and a major cause of long dry times. Use the vent length guidance and keep the ducting as short and straight as possible.
- Clean the lint screen every load
- Inspect and clean the vent duct and outside hood regularly
- Use rigid metal duct where possible
- Avoid crushed or kinked ducting
- Confirm the dryer is installed and vented per the installation guide
Use this to decide whether you should start with the element or airflow/limit devices.
- Drum tumbles, no heat at all: element, thermal limiter, high-limit thermostat, power supply
- Heats sometimes, dries slowly: vent restriction, crushed duct, lint buildup
- Repeated thermal limiter trips: airflow problem first, then check heating circuit
Last updated: February 2026
How to find Frigidaire dryer model number?
On a Frigidaire dryer like model FEQ332ES0, the model number is printed on the appliance data label; the most common spot is along the top edge of the door opening when you open the dryer door. Use the FEQ332ES0 installation guide for model-specific installation details and reference.
Check these common label locations (in order):
- Along the top of the door opening (with the door open)
- On the inside face of the door
- On the front panel just inside the opening (left or right side)
- On the rear panel of the cabinet
- Inside the console area (often where the wiring diagram is stored)
You will typically see a model number and a serial number. For parts lookup and diagrams, the model number is the key.
| Label item | What it’s used for | Example |
|---|---|---|
| Model number | Matching parts and diagrams | FEQ332ES0 |
| Serial number | Identifying production run | Unique to your unit |
We use the model number to match the correct Frigidaire dryer parts and configuration. Small model variations can change fit and wiring for items like the belt 134503600, door catch, or heating components.
- Wipe it gently with a damp cloth, then dry it
- Use your phone camera and zoom in (flash helps)
- Copy the model number exactly, including letters and zeros
Last updated: February 2026
What does code e64 mean on a Frigidaire dryer?
On a Frigidaire FEQ332ES0 dryer, error code E64 indicates a heating circuit problem. In most cases, the dryer is detecting an issue with the heating element circuit, such as an open heater, a tripped safety device, or a wiring connection problem.
- Reset power: switch the breaker OFF for 2 minutes, then turn it back on.
- Clean the lint screen completely.
- Check for strong airflow at the outside vent hood while the dryer runs.
- Inspect the vent duct for kinks, crushing, or heavy lint buildup.
- Make sure the dryer is not pushed tightly against the vent connection.
E64 is usually tied to the electric heat circuit. These are the most common areas to inspect after airflow checks.
| What you notice | What it usually means | What to check next |
|---|---|---|
| Dryer runs but no heat | Heater circuit is open | Heating element, wiring, terminals |
| Heat starts then stops | Overheat protection opened | Thermal limiter, vent restriction |
| Long dry times, cabinet feels hot | Exhaust restriction | Duct routing, vent hood, lint buildup |
If airflow is good and the code returns, these parts are frequent culprits on Frigidaire electric dryers.
- Frigidaire dryer heating element assembly 131553900 (open or damaged heater)
- Dryer thermal limiter 134120900 (opens if the dryer overheats)
- Terminal and wiring connections at the heater housing (loose, burned, or broken)
A restricted vent or failed heater safety device can cause overheating, no-heat drying, and repeat error codes. The installation instructions for this dryer call for inspecting and cleaning the exhaust system at least every 18 months with normal use.
For venting, electrical connection, and installation requirements (including grounding and duct routing), follow the FEQ332ES0 installation guide. For code definitions across Frigidaire dryers, use Frigidaire dryer error codes.
Last updated: February 2026
