Installation guide
Owner’s manual
Error Codes
Can I look up Frigidaire parts by model number?
Yes. Looking up parts by model number is the most accurate way to get compatible replacement parts for your Frigidaire gas dryer model FASG7073LW0 because it filters diagrams and parts lists to the exact configuration your dryer was built with. Use the full model number from the serial plate at the top of the door opening.
How to find the model number on your dryer
On FASG7073LW0, the model and serial numbers are on the serial plate located at the top of the door opening.
- Open the dryer door and look along the top edge of the opening
- Write the model number exactly as shown (letters and numbers)
- Record the serial number too (helpful for production variations)
- Keep the info with your paperwork or in your phone notes
How model-number lookup helps you choose the right part
When you search by model number, you can match parts to your dryer’s exact design, including door style, drum support, and gas-heat components.
| What you’re doing | Why it works | Example for FASG7073LW0 |
|---|---|---|
| Search by model number | Filters to compatible parts | Finds the correct belt, rollers, controls |
| Match by part ID | Confirms the exact item page | White-westinghouse dryer drum belt 134719300 |
| Use the manual for locations | Helps identify where parts fit | FASG7073LW0 owner’s manual |
Common parts customers look up by model number
These are frequent wear items on many Frigidaire dryers; model lookup ensures the right match.
- Drum belt (if the drum will not turn)
- Drum support rollers (if you hear thumping or rumbling)
- Thermistor (if drying temperature seems off)
- Door catch or strike (if the door will not stay closed)
- Gas valve coils (if a gas dryer heats intermittently)
Why it matters
Dryer parts can look similar but differ by mounting points, wiring connectors, and revisions. Using the exact model number (FASG7073LW0) reduces returns and helps your repair go smoothly the first time.
Last updated: February 2026
How much does it cost to replace a heating element in a Frigidaire dryer?
For the Frigidaire FASG7073LW0 gas dryer, “heating element” cost usually does not apply because gas models heat with a burner assembly, not an electric heater. Most repairs for “no heat” on this model involve airflow, gas supply, or ignition components, plus labor.
Typical cost ranges (parts + labor)
Costs vary by region and access, but these ranges are typical for a gas dryer like the FASG7073LW0:
- Service call/diagnostic: $99 to $150
- Common gas heat repair (parts + labor): $200 to $450
- Major gas heat repair (parts + labor): $350 to $650
- DIY parts-only (common): $20 to $300 (depending on the failed part)
| Repair scenario (gas dryer) | What you usually replace | Typical total cost |
|---|---|---|
| Runs but no heat | Gas valve coils, igniter, flame sensor | $200 to $450 |
| Weak heat, long dry times | Venting corrections, cleaning, minor parts | $150 to $350 |
| Intermittent heat | Gas valve coils, wiring checks | $200 to $450 |
| Gas valve failure (less common) | Gas valve assembly | $350 to $650 |
What to check first (often fixes “no heat” without major parts)
The owner’s troubleshooting checklist and installation requirements point to these high-impact checks:
- Confirm the gas supply valve is fully open (gas models)
- Clean the lint filter before every load
- Verify the exhaust duct is 4-inch rigid or semi-rigid metal, not plastic or foil
- Check the vent run for clogs, crushed sections, or too many bends
- Make sure the dryer has enough air supply to support the burner flame
For venting and safety requirements, follow the FASG7073LW0 installation guide.
Parts that commonly affect heat on this model
If airflow and gas supply are good, these parts are common suspects:
- Booster coil 5303931775 (gas valve coil kit; can cause intermittent or no ignition)
- Gas valve assembly (if the valve itself fails)
- Thermistor or other temperature sensing components (less common for “no flame”)
Why it matters
On a gas dryer, restricted venting can cause long dry times and overheating risk, and it can mimic a “bad heater” complaint. Correct venting and airflow often reduce repair cost and prevent repeat failures.
Last updated: February 2026
Where can I find my Frigidaire dryer model number?
On your Frigidaire gas dryer model FASG7073LW0, the model number is printed on the dryer’s serial plate located along the top of the door opening. Open the door and look up at the frame area to find the model and serial information.
What to look for on the serial plate
You will typically see several lines of information together:
- Model number (for example, FASG7073LW0)
- Serial number
- Electrical and gas information (varies by unit)
- Manufacturing codes used for service and parts matching
Quick steps to find it
- Turn the dryer off.
- Open the dryer door.
- Look at the top edge of the door opening (the cabinet frame).
- Write the model number exactly as shown (letters and numbers).
- Use that model number when ordering parts or checking diagrams in the FASG7073LW0 owner’s manual.
Why it matters
The model number is the key to getting the right Frigidaire dryer parts and repair instructions. Even small model changes can affect which drum belt, thermistor, or gas valve components fit your dryer.
| If you need to… | Use the model number for… |
|---|---|
| Order replacement parts | Matching exact fit and revisions |
| Troubleshoot symptoms | Finding model-specific checks and charts |
| Confirm accessories | Verifying kits and compatibility |
Last updated: February 2026
