Kenmore Elite 79572043111 refrigerator Parts

Kenmore Elite refrigerator model 79572043111 is a bottom freezer refrigerator in the 795.7205* / 7204* model family. For exact cabinet dimensions (height, width, depth), use the specifications section in the 79572043111 owner's manual, since size can vary slightly by door style and handle configuration.

What “size” usually means (and what to measure)

When customers ask for refrigerator size, we typically confirm these measurements:

• Width: side-to-side at the cabinet (and at the doors if they overhang)
• Height: floor to top of hinge cover (or top of cabinet)
• Depth: cabinet only, and with doors/handles
• Capacity: interior cubic feet (fresh food + freezer)
• Clearances: space needed for airflow and door swing

Quick measuring checklist (most accurate at home)

Use a tape measure and record in inches:

• Measure width at the widest point (often the doors)
• Measure height from floor to the highest point
• Measure depth three ways: cabinet only, with doors, with handles
• Confirm you have room to pull out drawers and open doors fully

Typical size range for this style of Kenmore bottom-mount

Most Kenmore bottom-mount refrigerators in this class are close to the following ranges (your exact numbers should come from the manual):

Measurement	Typical range
Width	~29 to 33 in.
Height	~68 to 71 in.
Depth (with handles)	~33 to 36 in.

Why it matters

Correct dimensions help prevent delivery issues and ensure proper airflow. Tight installations can also affect cooling performance and make it harder to service parts like the condenser area.

Last updated: January 2026

On Kenmore Elite refrigerator model 79572043111, DH typically indicates a defrost heater (defrost heating) problem, meaning the refrigerator is not heating the evaporator enough during the defrost cycle and frost can build up and reduce cooling. Use the 79572043111 owner's manual troubleshooting section to confirm the exact display behavior and checks.

What you’ll usually notice when DH shows

• Refrigerator section warming up or temperatures fluctuating
• Frost or ice buildup on the rear freezer panel
• Fan noise changes (fan hitting frost) or reduced airflow
• Ice maker performance issues due to poor freezer temps

Quick checks we recommend first

1. Power reset: Unplug for 5 minutes, then restore power.
2. Check door sealing and door closure: A leaking gasket can drive excess frost.
3. Look for heavy frost on the freezer back wall (a strong clue of a defrost system issue).
4. Confirm the unit is getting airflow: Don’t block vents with food packages.

Parts commonly involved in a DH/defrost-heating issue

A DH code is most often tied to the defrost circuit (heater, sensor, wiring, or control).

What can fail	What it affects	Example part for this model
Defrost sensor/thermistor assembly	Tells the control when to heat and when to stop	Refrigerator defrost sensor assembly 6615JB2005R
Electronic control board	Sends power to defrost components and monitors temps	Refrigerator electronic control board CSP30021078

Why it matters

If the defrost system is not working, frost can insulate the evaporator and block airflow. That forces longer run times, warmer temps, and can lead to food spoilage and ice maker problems.

Helpful reference

• For code meaning and symptom patterns on this Kenmore platform, use Kenmore 795 model bottom freezer refrigerator error codes.

Last updated: January 2026

On Kenmore Elite refrigerator model 79572043111, the most common problems we see are cooling failures (often tied to the sealed system or compressor), ice maker and water dispensing issues, and control or sensor problems that cause erratic temperatures or alarms. Use the 79572043111 owner's manual troubleshooting section to match symptoms to checks.

Most common symptoms and what they usually point to

• Not cooling or warm temperatures: compressor or sealed system issue, condenser airflow problem, or a control/sensor fault
• Ice maker not making ice: water supply restriction, ice maker failure, or freezer temperature too warm
• Water dispenser slow or no water: clogged water filter, kinked tubing, or inlet valve issue
• Frost buildup or temperature swings: defrost sensor/defrost system problem, door not sealing, or airflow damper issue
• Lights or door alarm acting up: door switch problem or control issue

Quick checks we recommend before replacing parts

1. Confirm temperatures: set freezer near 0°F and fresh food near 37°F; allow 24 hours to stabilize.
2. Check door sealing and loading: make sure doors close fully and vents are not blocked.
3. Inspect airflow and cleanliness: keep the grille area clear and clean dust from condenser areas if accessible.
4. Verify water supply: confirm the shutoff valve is open and the supply line is not kinked.
5. Reset after power events: after an outage, allow time for normal operation to return.

Parts that commonly solve these issues (when symptoms match)

Symptom	Commonly involved part	Example for this model
Bad taste/slow water flow	Water filter	Genuine Kenmore refrigerator water filter 9690 AGF80300801
Odors in fresh food section	Air filter	Lg refrigerator air filter ADQ73214408
Door alarm or lights inconsistent	Door switch	Refrigerator door switch 6600JB1010A
Frost or defrost errors	Defrost sensor	Refrigerator defrost sensor assembly 6615JB2005R
No ice production	Ice maker	Refrigerator ice maker assembly AEQ73110205

Why it matters

Catching the symptom pattern early helps prevent food spoilage and avoids unnecessary part swaps. For example, a clogged filter can mimic a dispenser failure, and a door not sealing can mimic a defrost problem.

When to use built-in diagnostics

This model supports Kenmore Connect phone-based diagnostics when the refrigerator has power and the controls are locked. The steps and timing are outlined in the 79572043111 owner's manual.

Last updated: January 2026

Water leaking from the bottom of your Kenmore Elite refrigerator model 79572043111 is usually caused by a clogged defrost drain that overflows into the cabinet, or a water supply/dispenser leak such as a cracked line or loose connection. Use the 79572043111 owner's manual to confirm access points and troubleshooting steps.

Most common causes (and what you’ll notice)

• Clogged defrost drain: Water collects under crisper drawers or runs out the front after defrost cycles.
• Dispenser or supply line leak: Drips near the back, under the unit, or along the water line path.
• Ice maker fill leak: Water appears after ice maker cycles, sometimes with ice buildup.
• Door not sealing well: Excess frost leads to heavy defrost water and overflow.
• Drain pan shifted or cracked: Water misses the pan and ends up on the floor.

Quick checks you can do safely

1. Unplug the refrigerator before inspecting inside panels or wiring.
2. Look for ice or sludge in the freezer floor area (a strong sign of a drain restriction).
3. Inspect the water line path for wet spots, kinks, or rubbing.
4. Check the door gaskets for gaps, tears, or areas that do not grip paper.
5. Confirm the unit is level (slight tilt back helps doors close and directs water to the drain pan).

Parts that commonly relate to bottom leaks

Leak source	What fails	Example part for this model
Dispenser/supply line	Cracked or split tubing	Refrigerator water tubing MJU62070602
Door seal	Warm air leaks in, creates excess frost and defrost water	Refrigerator door gasket, right ADX72930461

Why it matters

A small leak can turn into floor damage, ice buildup in the freezer, and poor cooling if airflow gets blocked. Fixing the drain or water line early also helps protect components like the evaporator fan and control board.

Helpful DIY guidance

• Follow the step-by-step tips in how to get rid of refrigerator puddles.
• If the leak seems tied to the dispenser area, use how to disassemble a Kenmore refrigerator dispenser to inspect fittings and tubing routing.

Last updated: January 2026