Whirlpool GS5SHAXSL01 side-by-side refrigerator Parts

The Whirlpool GS5SHAXSL01 is a full-size side-by-side refrigerator. For this model, plan on a cabinet that is about 36 inches wide and about 70 inches tall; depth varies the most depending on whether you measure the cabinet only or include doors and handles.

Measure the right way (so it fits your space)

Use a tape measure and record these before moving the refrigerator or planning a cutout:

• Width: left cabinet edge to right cabinet edge
• Height: floor to the highest point (often the hinge cover)
• Depth, cabinet only: back panel to front of cabinet (no doors)
• Depth, with doors/handles: back panel to the front of the handles
• Door swing clearance: extra space so doors open fully and bins slide out

Typical exterior size you should plan for

These planning dimensions cover real-world installation needs for GS5SHAXSL01, including clearance and door swing.

What you are planning for	What to allow	Why it matters
Opening width	~36 in. plus clearance	Prevents rubbing on cabinets and walls
Overall height	~70 in.	Avoids hitting soffits and upper cabinets
Depth	Cabinet-only is shallower; with handles is deeper	Affects walkway space and door swing

Why it matters

Accurate measurements prevent door interference, poor airflow around the condenser area, and sealing problems that can lead to warm temperatures, frost, or moisture.

Related parts that affect fit and door closing

If the doors do not close smoothly or sit level after a move, these model-matched parts are common fixes:

• Refrigerator door cam (black) WP2182179
• Refrigerator gasket panel (black) 2159083

Last updated: February 2026

For Whirlpool model GS5SHAXSL01, the correct replacement is the same filter type your refrigerator is designed to accept; on this model, the matching replacement is the refrigerator water filter EDR3RXD1. Confirm by matching the ID on your current filter or the filter housing, then replace and flush the system.

Quick ways to identify the right filter

• Match the filter ID printed on the current cartridge (letters and numbers must match).
• Check the filter housing label inside the refrigerator (often near the filter cap or grille).
• Compare the shape and end connections (twist-in vs push-in, O-ring location, length).
• Use your model number: GS5SHAXSL01 is the most reliable way to avoid mix-ups.
• Avoid look-alikes: similar Whirlpool side-by-side models can use different cartridges.

What to do if the old filter is missing or unreadable

If you cannot read the old cartridge, use the model-based match for GS5SHAXSL01 and install the refrigerator water filter EDR3RXD1. After installation, run water through the dispenser to clear air and carbon fines.

After you install a new filter

Step	What to do	What you should notice
Flush	Dispense several gallons of water over a few minutes	Water runs clear, sputtering stops
Ice	Dump the first bin of ice	Better taste, fewer particles
Leaks	Check the filter area and under the unit	No drips or wet spots

Why it matters

Using the correct refrigerator water filter helps protect the water inlet valve and ice maker from sediment, improves taste and odor, and keeps water flow strong for the dispenser and ice production.

Helpful DIY guidance

• How to replace the water filter in a Whirlpool refrigerator
• How to change the water filter in a Whirlpool refrigerator

Last updated: February 2026

“5-in-1 mode” is a convertible temperature feature found on some Whirlpool refrigerators that lets you switch a compartment between preset cooling profiles (for example: all-season, chef, dessert, party, or deep-freeze). On Whirlpool model GS5SHAXSL01, this specific “5-in-1” feature is not a standard function; it is typically associated with newer convertible designs.

What you can do on GS5SHAXSL01 instead

This side-by-side model uses traditional refrigerator and freezer temperature controls. If you are trying to get “party” or “deep freeze” performance, these steps get you closest:

• Set the freezer to 0°F and the fresh food section to 37°F (common targets for Whirlpool side-by-sides)
• Allow 24 hours for temperatures to stabilize after changes
• Make sure vents between compartments are not blocked by food packages
• Clean the condenser area so the compressor can shed heat efficiently
• Replace the water filter on schedule to keep dispenser flow strong (if equipped)

Quick comparison: “5-in-1” vs. standard controls

Feature	“5-in-1 convertible” refrigerators	GS5SHAXSL01 side-by-side
Preset modes (party, dessert, etc.)	Yes	No
Convertible compartment	Often	No
How you adjust temps	Mode selection	Temperature controls
Best use case	Flexible storage needs	Everyday fridge/freezer use

Why it matters

Mode-based systems change temperature targets automatically for specific food loads. With GS5SHAXSL01, you get the same results by using steady setpoints, good airflow, and keeping key cooling and water components in good shape.

Parts that commonly support performance

If you are troubleshooting cooling, ice, or water issues (often confused with “mode” problems), these model-matched parts are good starting points:

• Refrigerator water filter EDR3RXD1 (taste, odor, and flow issues)
• Refrigerator inlet valve W10408179 (no water to dispenser or ice maker)
• Whirlpool refrigerator ice maker assembly 2198597 (no ice or poor ice production)

For symptom-based troubleshooting, we use the steps in Whirlpool refrigerator error codes.

Last updated: February 2026

On the Whirlpool GS5SHAXSL01 side-by-side refrigerator, the water filter is located in the base grille (kickplate) at the bottom front of the unit. Look for a small filter door or a twist-out cartridge opening along the lower front edge.

How to find it on GS5SHAXSL01

Use these quick checks to spot the filter housing:

• Stand in front of the refrigerator and look along the bottom front grille
• Check the left and right ends of the grille for a small access door
• Look for a round cartridge end or a cap-style handle
• If the grille has a removable section, pull it off gently to expose the filter
• Keep a towel handy; a few drops of water are normal during removal

What the filter area looks like

What you see	What it means	What to do
Small door in the kickplate	Filter compartment	Open the door to access the cartridge
Round cartridge end exposed	Twist-out style filter	Turn and pull the cartridge out
Cap/handle on the cartridge	Helps removal and sealing	Make sure it is seated firmly

Replacement parts that match this model

For GS5SHAXSL01, use the correct cartridge and cap style so the filter seals and locks in place.

• Correct cartridge: refrigerator water filter EDR3RXD1
• If the cap is missing or damaged: refrigerator water filter cap (black) WP2260518B

Why it matters

Replacing the filter at the correct location prevents leaks at the housing, keeps dispenser flow strong, and helps avoid small or hollow ice cubes caused by restricted water flow.

For step-by-step replacement guidance that fits Whirlpool designs, use how to replace the water filter in a Whirlpool refrigerator.

Last updated: February 2026