Kenmore 66515112K217 dishwasher Parts

Yes. We still support parts for many Kenmore dishwashers, including model 66515112K217, by matching your exact model number to compatible replacement parts such as filters, drain pumps, inlet valves, spray arms, and door seals. Your model number is the key to getting the correct fit and electrical match.

How to find the right part for Kenmore 66515112K217

Use your model number 66515112K217 and confirm the symptom first (no drain, no fill, poor cleaning, leaks). Then match the part by name and ID.

Common part lookups for this model include:

• Draining problems: dishwasher drain pump W10876537, drain hose, air gap (if installed)
• Not filling or slow fill: dishwasher water inlet valve W11175771
• Poor cleaning or debris left behind: dishwasher filter WPW10463906, spray arm, filter cup
• Leaks at the sump or pump area: sump and seal, hose clamp, pump grommet
• No heat or poor drying: heating element

Parts that are commonly replaced (examples)

Here are a few examples of in-demand parts listed for 66515112K217:

Symptom	Part name	Part ID
Won’t drain / water left in tub	Dishwasher drain pump	W10876537
Won’t fill / not enough water	Dishwasher water inlet valve	W11175771
Dishes gritty / poor wash	Dishwasher filter	WPW10463906
Upper rack issues	Dishwasher dishrack slide rail stop, upper	WP8565925

Why the exact model number matters

Kenmore dishwashers are built in multiple design families, and parts can look similar but mount differently or use different connectors. Using 66515112K217 helps ensure:

• Correct fit (mounting points, hose sizes, rack hardware)
• Correct electrical ratings (pumps, heater circuits)
• Correct performance (spray pattern, filtration, fill rate)

Quick checks before ordering parts

We recommend these basic checks first because they often point to the right part:

• Confirm the door closes tightly and latches
• Check the circuit breaker or fuse if the dishwasher is dead
• Start a short cycle and verify there is water in the bottom of the tub after a couple minutes
• Clean the filter and check the spray arm for clogs
• Inspect the drain hose routing for kinks or a blocked connection

For model-specific operating and care steps, use the 66515112K217 owner’s manual.

Last updated: February 2026

To tell which Kenmore dishwasher you have, we look up the model number on the rating label. On Kenmore model 66515112K217, the label is typically on the inside edge of the door or the tub opening when you open the door.

Where to find the model and serial label

Check these common spots first (in order):

• Inside the door along the left or right edge
• Along the top edge of the tub opening (under the counter lip)
• On the side wall of the tub opening near the front
• On the inner door panel area near the latch

Once you find it, write down both the model number and serial number exactly as shown.

What to do with the model number

Use the model number to match the correct parts list, diagrams, and instructions for your exact dishwasher.

What you need	Where it’s used	Why it helps
Model number (example: 66515112K217)	Parts lookup, diagrams, manuals	Ensures parts fit and procedures match
Serial number	Service history, production details	Helps identify version changes

Quick tips to avoid mix-ups

• Match every character (numbers and letters) exactly
• Don’t use the number from the control panel styling or door badge
• If the label is hard to read, take a clear photo and zoom in
• Use the instructions in the 66515112K217 owner’s manual to confirm you’re identifying the correct unit

Why it matters

Kenmore dishwashers can look similar across multiple series, but internal components like the water inlet valve, drain pump, and heating element can vary by model. Using the rating label prevents ordering the wrong part and saves time on repairs.

Last updated: February 2026

Water standing in the bottom of your Kenmore dishwasher model 66515112K217 usually means the unit is not draining fully, or you are seeing the small amount of water that is normal during operation checks. Start by running CANCEL/DRAIN to force a drain cycle, then check the filter area and drain path for clogs.

Quick checks (most common causes)

• Press CANCEL/DRAIN once, then close the door within 3 seconds and let the drain run (about 2 minutes).
• Remove and clean the bottom filters; debris here is the most common reason for slow draining.
• Check the sink drain or garbage disposer connection; the disposer inlet knockout plug must be removed.
• Inspect the drain hose for kinks, crushing, or a blockage.
• Look for food or labels stuck at the drain inlet area inside the tub.
• If you hear a hum but no draining, the drain pump may be jammed or failing.

What “some water in the tub” can mean

During installation and operation checks, it is normal to see water in the bottom of the tub shortly after starting a cycle. If the dishwasher finishes a cycle and still has standing water above the filter area, that points to a drain problem.

What you see	When it happens	What it points to
Small puddle at the bottom	Early in a cycle	Normal fill/check condition
Water remains after cycle ends	End of cycle	Drain restriction or drain pump issue
Water backs up from sink	When sink drains	House drain/disposer restriction

Parts that commonly fix “won’t drain” symptoms

If cleaning and hose checks do not solve it, these model-compatible parts are common next steps:

• Dishwasher drain pump W10876537 (drains water out of the tub)
• Dishwasher drain hose 8269144A (can clog, kink, or collapse)
• Dishwasher filter WPW10463906 (restricted filtration can slow water flow)

Why it matters

Standing water can cause odors, redeposit soil on dishes, and strain the drain pump. Restoring proper draining protects the pump and helps the dishwasher clean and dry correctly.

Where to find the exact steps for your model

For the correct drain procedure, filter location, and troubleshooting chart for 66515112K217, follow the instructions in the 66515112K217 owner’s manual.

Last updated: February 2026