Kenmore 66513049K113 undercounter dishwasher Parts

For a Kenmore undercounter dishwasher model 66513049K113, repair is usually worth it when the problem is isolated (draining, heating, filling, or a rack issue) and the tub is in good shape. If repairs are frequent or multiple major systems are failing, replacement is typically the better value.

Quick decision checklist

• The dishwasher completes cycles and only one function is failing (heat, drain, fill, spray).
• The tub is not leaking and the door closes and latches normally.
• You want to avoid the time and cost of uninstalling and reinstalling an undercounter unit.
• The issue is a common wear part (pump, valve, heating circuit, rack hardware).
• You can confirm basics first (power, water on, cycle set) using the 66513049K113 installation guide.

Common repairs that often make sense

These are typical “single-system” fixes that can restore performance without replacing the whole dishwasher:

Symptom	What to check first	Example part for this model
Not draining	Kinked/clogged drain hose, disposal knockout, drain path	Dishwasher drain pump WPW10348269
Dishes not drying or water not heating	Heating circuit, high-temp options, cycle selection	Dishwasher heating element W10518394
Not filling or fills slowly	Water supply on, inlet screen, valve	Dishwasher water inlet valve WPW10327249
Poor wash coverage	Spray arm clogs, loading, water temp	Dishwasher spray arm WPW10491331

When replacement is usually the better choice

• You have repeated breakdowns across different systems (drain, heat, and controls).
• The dishwasher has chronic leaks from the tub or sump area.
• The unit has become unreliable enough that you are re-washing dishes often.
• Installation constraints make repeated service calls costly (tight cabinet opening, hard plumbing).

Why it matters

A dishwasher like the 66513049K113 is designed to clean using spray, then pause for detergent soak; longer cycles can be normal and not a “failure.” Knowing what is normal helps you avoid replacing a dishwasher that only needs a targeted part repair.

Last updated: February 2026

Common problems we see with the Kenmore 66513049K113 dishwasher include not starting, not draining, poor cleaning, and not drying. Many issues come down to power and latching checks, water supply being off, or a failed component such as the drain pump, heating element, or control.

Quick checks first (most “no start” calls)

Before replacing parts, we recommend these basics from the setup and operation checks in the installation guide:

• Reset the breaker or replace a blown house fuse.
• Confirm the door is fully closed and latched.
• Make sure a cycle is selected correctly (then press Start).
• Verify the water supply valve to the dishwasher is turned on.
• Start a short cycle; after about 2 minutes, open the door and confirm there is water in the bottom of the tub.

Common symptoms and the parts that often fix them

Symptom	What it usually points to	Example part for 66513049K113
Won’t drain, standing water	Drain restriction or failed drain pump	Dishwasher drain pump WPW10348269
Dishes not dry, water stays cool	Heating circuit issue	Dishwasher heating element W10518394
Poor wash coverage, food left behind	Clogged or damaged spray arm, circulation issues	Dishwasher spray arm WPW10491331
Won’t fill or fills slowly	Water supply problem or inlet valve issue	Dishwasher water inlet valve WPW10327249
Starts then acts erratic or won’t respond	Control or wiring problem	Dishwasher electronic control (model-specific)

Why it matters

Dishwashers rely on correct fill, strong spray, proper draining, and heat. If any one of those steps fails, you can get symptoms that look unrelated (for example, a drain problem can also cause poor cleaning and odors).

Safety and installation-related causes we see

Installation and routing issues can create repeat problems over time. These are common contributors:

• Drain hose routed with kinks or improper height.
• Water line or wiring contacting the motor/legs.
• Dishwasher not level, affecting door latching and wash performance.
• Freezing exposure to the unit or supply line.

Last updated: February 2026

Your Kenmore dishwasher’s model number is printed on the model and serial tag attached to the dishwasher frame. For Kenmore 66513049K113, check the door area first; the tag is typically visible when you open the door. For exact tag location illustrations, use the 66513049K113 installation guide.

Where to look on the dishwasher

Check these common spots in this order:

• Open the door and look along the inner door edge (left or right side)
• Look on the tub frame around the door opening (top or sides)
• Check the side of the inner door panel near the latch area
• If the unit is pulled out, check the side panel near the front

What the model number looks like

On the tag, you will usually see:

• Model (this is the number you need for parts): 66513049K113
• Serial (unique to your unit)
• Electrical ratings (volts/amps) and other manufacturing info

Quick ID table

Tag item	What it’s used for	Example
Model number	Matching parts and diagrams	66513049K113
Serial number	Production details	Varies

Why it matters

Using the full model number (including the suffix) ensures the correct fit for parts like a dishwasher heating element, water inlet valve, or drain pump. Even small model-number differences can change the rack components, control, or wiring harness used.

Last updated: March 2026