Kenmore 79551033010 refrigerator Parts

For Kenmore side-by-side refrigerator model 79551033010, we replace the water filter by turning off the household water supply, removing the old filter from the right-side filter housing in the fresh food compartment, installing the new filter (lock symbol facing you), then purging 2.5 gallons and resetting the filter light.

Step-by-step: replace the water filter

1. Turn off the household water supply.
2. Remove the top shelf (then move it to the lowest level for access).
3. Remove the old filter:
   • Turn the filter counterclockwise.
   • Pull it down to remove.
4. Install the new filter:
   • Remove the red cap from the new filter.
   • Insert the filter into the receptacle.
   • Push up and rotate clockwise until it locks.
   • Confirm the lock symbol faces you and the filter will not rotate further.
5. Turn the household water supply back on.
6. Purge air and carbon fines: dispense 2.5 gallons (9.46 L) using 30 seconds ON / 60 seconds OFF cycles.
7. Check for leaks around the filter housing and shelf area.

Reset the filter indicator

When the Filter Reset icon turns on, press and hold Filter Reset for 3 seconds to turn the icon off. See the 79551033010 owner’s manual for the exact button location and display behavior.

Quick checklist (prevents leaks and weak flow)

• Turn off the water supply before removing the filter.
• Make sure the filter is fully seated and locked (lock symbol facing you).
• Reinstall the shelf after the filter is locked in.
• Purge the full 2.5 gallons to clear air and improve taste.
• If you remove the filter and do not replace it, reinstall the substitute cap to prevent leaks.

Common symptoms and what they usually mean

Symptom	Most common cause	What to do
Water leaks after replacement	Filter not locked fully	Remove and reinstall until lock symbol faces you
Slow dispenser flow	Air in line or clogged filter	Purge 2.5 gallons; replace filter if flow stays weak
Filter light stays on	Reset not completed	Hold Filter Reset for 3 seconds

Why it matters

A properly installed filter protects the water system from debris, helps maintain dispenser flow, and prevents leaks at the filter housing. Purging after installation also clears trapped air that can cause sputtering.

For additional filter tips and styles used across Kenmore refrigerators, use how to replace the water filter in a Kenmore refrigerator.

Last updated: January 2026

Kenmore side-by-side refrigerator model 79551033010 measures 35 3/4 in. wide, 69 7/8 in. high (to top of hinge), and 35 3/8 in. deep (including the handle). For best cooling performance, plan for at least 2 inches of clearance around the cabinet.

Quick dimension summary

• Width: 35 3/4 in.
• Height: 69 7/8 in. (top of hinge)
• Depth: 35 3/8 in. (with handle)
• Recommended clearance: 2 in. minimum on sides and top for airflow

Measurement	What it includes	Value
Width	Cabinet side to side	35 3/4 in.
Height	Floor to top of hinge	69 7/8 in.
Depth	Back to front of handle	35 3/8 in.
Clearance	Space around cabinet	2 in. minimum

How we recommend measuring at home (for a perfect fit)

Even with published specs, measuring your actual unit and the opening prevents surprises.

• Measure width at the widest point with doors closed
• Measure height from floor to the highest point (often the hinge cover)
• Measure depth two ways: to the door face, then to the front of the handle
• Measure the opening and note baseboards, trim, and nearby walls

Why it matters

If the refrigerator is squeezed into a tight cutout, airflow drops and the unit can run longer and warmer. Clearance also helps with door swing, leveling, and pulling the refrigerator out for service.

For the full installation and spacing guidance, use the 79551033010 owner's manual.

Last updated: January 2026

On Kenmore side-by-side refrigerator model 79551033010, the model number is printed on the identification label inside the fresh food (refrigerator) compartment, on the right-hand side. The same label also lists the serial number, which you may need when ordering parts or scheduling service.

Where to look (fast checklist)

• Open the refrigerator (fresh food) door, not the freezer door
• Look along the right interior wall of the refrigerator compartment
• Check near the front edge where the door gasket seals
• Use a flashlight; the label can be small or partially shadowed
• Write down the full model number and serial number exactly as shown

What the label includes

The identification label typically shows these items:

• Model number (for example, 79551033010)
• Serial number
• Electrical ratings and other technical information

What you need	Why you need it	Example format
Model number	Ensures parts fit your exact refrigerator	79551033010
Serial number	Helps match production details and revisions	Letters plus numbers

Why it matters

Kenmore refrigerators often have multiple versions that look similar. Using the exact model number helps us match the correct diagrams and parts, such as a refrigerator electronic control board EBR64734401 or a refrigerator door gasket 4987JJ1010M, so you avoid returns and repeat repairs.

Reference

For a picture-based location guide and other model-specific details, use the 79551033010 owner's manual.

Last updated: January 2026