Frigidaire GLER642AS3 dryer Parts

To reset an E64 error on your Frigidaire GLER642AS3 dryer, we recommend disconnecting power for about 5 minutes, then restoring power and trying a timed dry cycle. If E64 returns, the problem is typically in the heater circuit and needs troubleshooting.

• Turn the cycle selector to OFF.
• Unplug the dryer (or switch the breaker OFF).
• Wait 5 minutes.
• Restore power.
• Close the door and press Start (hold 1 to 2 seconds on many models).

For control and start procedure details, use the GLER642AS3 owner's manual.

E64 is commonly associated with an electric-heating problem such as an open heater circuit, a tripped thermal device, or a failed thermostat.

• Verify the dryer has the correct power supply (electric dryers often need two hot legs; a partial power loss can let the drum run but stop heat).
• Check for restricted airflow (clogged lint screen, crushed vent, blocked exterior hood).
• Inspect the heater circuit safety devices; a tripped thermal limiter can stop heat.
• If the dryer runs but will not heat, test the heating components with a meter.
• If the dryer will not start after the reset, review the no-start checklist items (power cord fit, breaker/fuse, door closed).

An E64 that comes back after a reset usually means the dryer is protecting itself because the heater circuit is not operating normally. Fixing airflow issues and failed heater components helps restore normal drying times and prevents repeat shutdowns.

You can also reference our Frigidaire dryer error codes guide to compare symptoms and next steps.

Last updated: February 2026

For a Frigidaire GLER642AS3 dryer, the total cost to replace the heating element is usually the price of the part plus labor. The heating element assembly for this model is the Frigidaire dryer heating element assembly 131553900, and professional installation commonly brings the total into the $200 to $400 range.

Replacement cost depends on whether you DIY or hire service.

• Part cost: varies by availability and seller (for GLER642AS3, the element is 131553900)
• Labor: commonly 1 to 2 hours for an electric dryer element replacement
• Service call/diagnostic fee: often added if a technician confirms the failure first
• Extra parts: sometimes needed if overheating damaged safety components

If the dryer overheated or airflow was restricted, we often see a safety device fail along with the element.

• Frigidaire dryer heating element assembly 131553900
• Dryer thermal limiter 134120900
• Kelvinator dryer high-limit thermostat 3204267

A dryer that runs hot because of restricted venting can repeatedly damage the heating circuit (element, high-limit thermostat, thermal limiter). Fixing airflow issues at the same time helps the new part last longer.

Use these checks to avoid replacing a good heating element.

• Clean the lint screen and housing
• Confirm strong airflow at the outside vent hood
• Inspect the vent duct for kinks, crushing, or heavy lint buildup
• If the dryer is gas, follow the safety instructions in the GLER642AS3 owner's manual and use a qualified servicer

Last updated: February 2026

On a Frigidaire dryer like model GLER642AS3, the main parts are the drum system that tumbles clothes, the drive system that turns the drum, the heating and airflow system that dries, and the controls and safety devices that regulate temperature and operation. For diagrams and locations, use the GLER642AS3 owner's manual.

• Drum and supports: holds laundry and rotates on glides/bearings
• Drive system: motor, belt, idler, and pulleys that spin the drum
• Heating system (electric models): heating element plus thermostats/limiters
• Airflow system: blower wheel, lint screen housing, exhaust duct/vent
• Controls and switches: timer/control board, start switch, door switch
• Safety devices: thermal limiter/thermal fuse, high-limit thermostat

These are some of the most frequently serviced components for this model:

Knowing which system is involved helps you troubleshoot faster and replace the right part the first time. For example, restricted airflow can cause long dry times and overheating; the manual also calls out cleaning the lint screen every load and periodic exhaust duct cleaning for safe, efficient drying.

• Clean the lint screen before or after each load
• Keep the exhaust vent run short and free of lint buildup
• Avoid overloading; most loads should fill the drum about 1/3 to 1/2 full
• Use Air Fluff (no heat) for foam rubber, plastic, feathers, or down

Last updated: February 2026

On a Frigidaire GLER642AS3 dryer, error code E64 points to a heating circuit problem, most commonly the heating element or its wiring. We treat E64 as a “no heat or heat fault” signal and troubleshoot the heater, thermostats, and connections.

• Reset power: unplug the dryer (or switch off the breaker) for 2 minutes, then restore power.
• Confirm airflow: clean the lint screen and make sure the vent is not crushed or clogged.
• Check for heat symptoms: runs but no heat, heats briefly then stops, or trips a breaker.
• Inspect wiring at the heater housing for loose, burned, or broken terminals.
• If the drum turns but there is still no heat, test the heater circuit parts with a multimeter.

E64 usually traces back to the heater circuit. On GLER642AS3, these parts are frequent suspects:

Restricted venting makes the heater area run hotter than normal. That can open a thermal limiter or high-limit thermostat, and the control can then flag a heater-related code like E64. Fixing venting first prevents repeat failures after replacing a heating part.

For GLER642AS3-SPECIFIC safety notes, access panels, and component locations, follow the GLER642AS3 owner’s manual.

Last updated: February 2026

On a Frigidaire GLER642AS3 dryer, error code E53 points to a motor circuit problem; most often the control is not sensing the motor’s running state (commonly tied to the motor’s centrifugal switch or the control’s motor feedback circuit).

• Reset power: unplug the dryer (or switch off the breaker) for 2 minutes, then restore power.
• Confirm the drum turns by hand; it should rotate smoothly without scraping.
• Check for a jam: remove items and look for foreign objects in the drum area.
• Clean airflow basics: lint screen and venting; restricted airflow can contribute to overheating and shutdowns.
• If the code returns immediately when you press Start, focus on the motor circuit and door switch/controls.

If the drum feels tight or noisy, these wear items can increase motor load and trigger motor-related faults:

• Belt 134503600 (drum drive belt)
• Dryer drum bearing kit 5303281153 (rear support components)
• Dryer drum glide 137513300 (front support glide)

E53 is a “motor state” problem; continuing to run the dryer with a binding drum or failing motor circuit can lead to repeated shutdowns, poor drying, and additional electrical or mechanical damage.

Follow the electrical safety and operating guidance in the GLER642AS3 owner’s manual before accessing internal components.

Last updated: February 2026

If your Frigidaire GLER642AS3 dryer runs but the drum will not turn, the most common cause is a broken or slipped drum belt, or a drum support issue (glides or rear bearing) that is binding the drum. Use the GLER642AS3 owner's manual to confirm the correct start procedure and basic checks.

• Make sure the door fully closes and latches; the dryer stops when the door opens.
• Confirm the cycle selector is not set to OFF.
• Press and hold the start control for 1 to 2 seconds (some versions use a push button).
• Listen for motor sound or humming; humming often points to a jammed drum or failed belt.
• Unplug the dryer before inspecting internal parts.

1. Try turning the drum by hand (dryer unplugged). If it is very stiff, suspect a bearing/glide bind.
2. Start the dryer and listen:
   • Motor sound with no drum movement: belt is likely broken or off the pulley.
   • Humming then stopping: drum may be jammed, or the belt is tangled.
3. Check for heat and airflow issues separately; restricted venting can overheat components, but it usually does not stop the drum from turning.

A dryer that is not spinning can overwork the drive motor and increase wear on drum supports. Fixing a worn belt or bearing early helps prevent bigger repairs and keeps drying times normal.

Last updated: February 2026