Kenmore Elite 41741100000 washer Parts

Yes. Your Kenmore Elite 41741100000 washer uses a drain-pump cleanout filter (coin trap style) that catches lint, hair, and small items before they reach the drain pump. Cleaning it regularly helps prevent slow draining, standing water, and drain-related error codes.

Where the filter is and what it does

On most Kenmore 417-series front-load washers, the filter is accessed from the lower front of the cabinet (behind a small access panel). It protects the drain system by trapping debris before it can jam the impeller.

• Catches coins, buttons, and lint
• Helps the washer drain and spin normally
• Reduces pump noise caused by debris
• Helps prevent leaks from a blocked drain path

How we recommend cleaning the washer filter

Follow the access and cleanout steps in your 41741100000 owner's manual. In general, the process looks like this:

• Unplug the washer (or switch off power at the breaker)
• Place towels and a shallow pan under the front access area
• Open the lower access panel
• Drain any water from the cleanout area slowly
• Unscrew the filter, remove debris, and rinse it
• Reinstall the filter snugly (hand-tight), then run a quick rinse/drain test

Parts that are commonly involved

If the filter housing is damaged, the cap will not seal, or the washer still will not drain after cleaning, these model-matched parts are the usual suspects:

Symptom	Most likely part to check	What it affects
Won’t drain, hums, or drains slowly	Washer drain pump 137240800	Pumping water out of the tub
Debris keeps returning, filter won’t seat	Washer drain pump filter 134640200	Cleanout filter and sealing surface
“No fill” or fill is very slow (not a filter issue)	Washer water inlet valve 134637810	Water entering the washer

Why it matters

A clogged filter can mimic bigger failures (like a bad drain pump) and can trigger drain and unbalance problems during spin. Keeping the filter clean is one of the fastest ways to restore normal draining and protect the pump.

Last updated: February 2026

To force-drain a Kenmore Elite washer model 41741100000, we first shut off power, then manually drain water from the front drain area and clear the most common blockage points (pump filter and drain hose). This safely gets standing water out so you can restore normal draining.

Safe forced-drain steps (front-load style)

1. Unplug the washer (or switch off the breaker). The installation instructions stress verifying power is off before plugging in or servicing.
2. Turn off both water supply valves (hot and cold) to prevent additional filling.
3. Protect the floor: place towels and a shallow pan at the front bottom of the washer.
4. Open the lower access area and slowly loosen the pump filter cap to let water trickle into the pan.
5. Remove debris (coins, lint, small socks) from the filter and housing.
6. Reinstall the filter cap snugly, then check the drain hose for kinks, pinches, or a clog at the standpipe/laundry tub.

• Unplug power before opening any panels
• Drain in small amounts to avoid spills
• Clear the filter cavity completely (including behind the filter)
• Confirm the drain hose is secured and not pushed too far into the standpipe
• Run a quick rinse/spin to confirm normal draining

Parts that commonly fix “won’t drain”

If the filter and hose are clear but the washer still will not drain, these parts are frequent causes on this platform:

Symptom	Most likely cause	Part to consider
Hums but no drain flow	Jammed or failed pump	Washer drain pump 137240800
Slow drain, recurring clogs	Restricted filter or damaged filter housing	Washer drain pump filter 134640200
Overfills or odd water level behavior	Pressure sensing issue	Washer water-level pressure switch 134762010

Why it matters

Standing water can trigger out-of-balance issues, odors, and repeat drain errors. Getting the tub empty first also makes troubleshooting safer and prevents water damage.

Helpful reference

• For model-specific panel access, drain routing, and safety notes, use the installation guide.

Last updated: February 2026

To hard reset a Kenmore Elite washer model 41741100000, we power-cycle it to clear a temporary control glitch: unplug the washer (or turn off the breaker), wait briefly, then restore power and restart a cycle. For model-specific button sequences, use the 41741100000 installation guide.

Quick hard reset (power-cycle)

• Press POWER to turn the washer off.
• Unplug the washer (or switch the circuit breaker OFF).
• Wait 1 minute.
• Restore power; after first plug-in, the washer can take about 1 minute to boot up.
• Press POWER, select a cycle, and press START.

If the washer is acting up right after install

The installation instructions include a built-in Installation Cycle that runs diagnostics and can help after setup issues (no water, hoses reversed, etc.). Use the steps in the 41741100000 installation guide to start that diagnostic routine.

Common “reset-like” fixes to do at the same time

• Confirm both water supply valves are fully open.
• Reseat the power cord; avoid extension cords.
• Check the drain hose is not shoved too far down the standpipe.
• Level the washer to reduce vibration and false out-of-balance behavior.
• If an error code is showing, look it up before replacing parts.

What to do if an error code returns

A reset helps only when the control is “stuck.” If the same code comes back, troubleshoot the cause.

Symptom after reset	Most likely area to check	Example part for this model
Won’t fill or fills slowly	Water supply, inlet screens, inlet valve	Washer water inlet valve 134637810
Won’t drain	Drain hose, pump filter, drain pump	Washer drain pump filter 134640200
Shuts down or won’t spin	Load balance, door lock system, control issues	Use error code guide

Helpful troubleshooting reference

Use our Kenmore 417 front load washer error codes guide to match the displayed code to the right checks.

Why it matters

Resetting clears temporary electronic faults, but repeated errors usually point to a real issue (water supply, draining restriction, leveling, or a failing component). Using the correct diagnostic steps prevents unnecessary part replacement.

Last updated: February 2026

Yes, repairing a Kenmore Elite washer like model 41741100000 is worth it when the fix restores reliable operation for less than the cost of replacing the washer. In most homes, a solid repair on a key failure (drain, fill, control, or suspension) is the better value.

How we decide if repair makes sense

We use a simple cost and condition check before buying a new washer:

• Repair cost vs. replacement cost: If the repair is clearly cheaper, repair wins.
• What failed: Wear items (pump, valve, pressure switch) are usually straightforward.
• How the washer has been behaving: Repeated leaks, loud spin, or multiple recent failures push toward replacement.
• Downtime and labor: Some repairs are quick; tub and bearing level work is not.
• Safety and setup: Follow the installation guide for safe access, clearances, and power-off steps.

Common repairs that are usually “worth it”

These are frequent front-load washer fixes that often restore full performance:

• No drain or slow drain: clean/replace the washer drain pump filter 134640200 or replace the drain pump
• No fill or fill errors: replace the washer water inlet valve 134637810
• Overfilling or water level problems: replace the water-level pressure switch
• Excessive vibration: inspect shocks and counterweights, then correct leveling

Quick cost-to-benefit comparison

Situation	Typical outcome	Usual recommendation
Single failed part (pump, valve, switch)	Restores normal cycles	Repair
Repeated leaks plus vibration	Multiple parts likely	Price out repair first
Major tub or bearing work	High labor, long downtime	Compare closely to replacement

Why it matters

A front-load washer’s biggest value is in its core systems (fill, drain, motor control, suspension). When one of those fails, replacing the right part can return the washer to normal efficiency and spin performance without the cost and hassle of a new installation.

Last updated: February 2026

Most Kenmore washers last 10 to 15 years. For the Kenmore Elite 41741100000, lifespan depends mainly on load size, how often it runs, and basic upkeep like keeping the drain system clear and the washer properly installed (see the 41741100000 installation guide).

Typical lifespan and what affects it

A washer’s service life is usually driven by wear on moving parts (motor, shocks, tub bearings) and water-handling parts (pump, inlet valve, hoses).

• Usage frequency: multiple loads per day shortens life faster than a few loads per week
• Overloading: increases strain on the drive system and suspension
• Installation quality: an unlevel washer can vibrate and wear parts early
• Water conditions: sediment can stress fill components
• Maintenance: cleaning and checking for small leaks prevents bigger failures

Common “end-of-life” symptoms

If you’re deciding whether to repair or replace, these are the most common signs the washer is nearing the end of its typical lifespan:

• Loud rumbling or grinding during spin
• Repeated no-drain or slow-drain problems
• Frequent out-of-balance shaking or walking
• Water not filling correctly or filling very slowly
• Leaks around the door area or underneath the cabinet

Parts that often drive repair decisions

On front-load Kenmore Elite washers, these parts commonly come up when performance drops:

Symptom	Often involved part	Example part for 41741100000
Won’t drain / drains slowly	Drain pump or filter	Washer drain pump 137240800, washer drain pump filter 134640200
Won’t fill / fill errors	Water inlet valve	Washer water inlet valve 134637810
Excessive vibration	Suspension components	Shock absorbers (varies by configuration)

Why it matters

Knowing the 10 to 15 year average helps you plan: if your 41741100000 is already in that range and needs a major repair (motor, control board, tub work), comparing repair cost to replacement value usually leads to a clearer decision.

Last updated: February 2026

Your Kenmore Elite washer’s model number is printed on a rating label attached to the washer cabinet. On Kenmore front-load washers like model 41741100000, the label is most often found around the door opening (door jamb) or just behind the door.

Where to look first (fastest checks)

• Open the washer door and check the door jamb (the frame area the door closes against)
• Look just inside the door opening on the front panel
• Check the side of the main cabinet near the bottom (left or right side)
• Look on the back of the control panel or rear panel

What the model label looks like

Most Kenmore washer labels include:

• Model number (example: 41741100000)
• Serial number
• Electrical ratings (voltage/amps)
• Sometimes a barcode

Tips to read and use the model number correctly

• Copy the model number exactly as printed, including all digits
• Use the model number to match parts like the washer water inlet valve 134637810 or washer drain pump 137240800
• If the label is worn, take a clear photo with good lighting and zoom in

Quick reference table

Location	How to check	Most common on front-load washers
Door jamb / door opening	Open door, inspect frame and inner lip	Yes
Back of control panel	Look behind console area	Sometimes
Side panel near bottom	Inspect lower side cabinet	Sometimes
Rear panel	Check back of washer cabinet	Sometimes

Why it matters

The exact model number ensures we match the correct Kenmore Elite washer parts, installation details, and troubleshooting steps. Even small model-number differences can change the correct control board, drain pump, or door boot hardware.

For additional model-identification and setup details, use the installation guide.

Last updated: February 2026

Kenmore Elite is a premium Kenmore product line that has been sold across multiple years (not a single “made in” year). For your Kenmore Elite washer model 41741100000, the exact manufacture date is typically determined from the model’s serial number and the date-code information shown in the 41741100000 owner's manual.

What “Kenmore Elite” means (and what it does not)

Kenmore Elite is a series name used on higher-end Kenmore appliances; it does not identify one specific production year.

Common ways we see “Kenmore Elite” used:

• A premium trim level within Kenmore washers, dryers, refrigerators, and ranges
• A grouping of features (capacity, cycles, controls) rather than a date
• A label that can span multiple model families and production runs

How to find the manufacture date for model 41741100000

The most reliable way is to use the serial number from the washer’s rating plate, then match it to the date-code format in the documentation.

Steps we recommend:

• Locate the rating plate (often inside the door opening on front-load washers)
• Write down the full model number (41741100000) and serial number
• Check the serial/date-code section in the 41741100000 owner's manual
• If you are installing or moving the washer, keep the serial info handy while following the installation guide

Quick reference: “series name” vs “manufacture date”

Item	What it tells you	Example
Kenmore Elite	Product line / feature tier	“Elite washer”
Model number	Exact design family	41741100000
Serial number	Unit-specific build info	Used to decode date

Why it matters

Knowing the manufacture date helps us match the correct replacement parts (like a water inlet valve, drain pump, or control board) and confirm compatibility when a design changes mid-series.

Last updated: February 2026

On the Kenmore Elite 41741100000 washer, the “filter” most owners mean is the drain pump clean-out, which is typically accessed from the lower front of the washer behind a small access panel (or the lower kick panel). Use the steps in the 41741100000 owner's manual to match the exact access method for your console and cabinet.

How to find and access the drain pump filter

In most Kenmore Elite front-load designs, the drain pump filter is at the bottom front so you can clean out coins, lint, and small items.

• Unplug the washer before opening any access panel.
• Look along the bottom front edge for a small rectangular door or a panel held by screws.
• Place a shallow pan and towels under the opening; some water usually drains out.
• Slowly open the filter cap (turn counterclockwise) and let water drain in a controlled way.
• Remove debris from the filter and the pump cavity, then reinstall the cap snugly.
• Reinstall the access panel and run a quick rinse or drain/spin to confirm no leaks.

Parts that relate to the “filter” area

If the cap is damaged, the housing leaks, or the washer will not drain after cleaning, these parts are commonly involved:

Symptom	Most likely area	Related part for model 41741100000
Won’t drain, humming pump	Pump or blockage	Washer drain pump 137240800
Repeated clogs, missing/warped screen	Filter assembly	Washer drain pump filter 134640200

Why it matters

A clogged drain pump filter can cause slow draining, standing water, odor, and spin problems. Cleaning it regularly helps protect the drain pump and keeps cycles finishing normally.

Last updated: February 2026