Kenmore 66513263K110 undercounter dishwasher Parts

Yes. We still carry replacement parts for Kenmore dishwashers, including the Kenmore 66513263K110 undercounter dishwasher, as long as the part is still manufactured and available. The key is matching parts by your exact model number so the fit and electrical connections are correct.

How to make sure you order the right part

Use the model number 66513263K110 and confirm the part’s location in the diagrams and parts list in the 66513263K110 owner's manual.

Before you buy, we recommend:

• Match the full model number from the dishwasher’s rating label (not just “665”).
• Compare the part name and part ID, not only the description.
• Check whether your issue is a rack problem, draining problem, filling problem, or heating problem.
• Verify any included hardware (clips, screws, brackets) if you are replacing an assembly.
• Review installation clearances and connections if you are pulling the dishwasher out.

Common Kenmore dishwasher parts we can still supply

For this model, these are examples of commonly replaced parts that are currently listed:

Symptom	Part that often fixes it	Example part ID
Upper rack won’t adjust or sags	Rack adjuster kit	W10712395
Dishwasher won’t drain or drains slowly	Drain pump	WPW10348269
Not filling or fills very slowly	Water inlet valve	W11175771
Poor wash coverage	Spray arm	WPW10491331
Dishes not drying well	Heater	W10703867

If you are troubleshooting a drain issue, the dishwasher drain hose 8269144A is also a common wear item to inspect for kinks, clogs, or leaks.

Why it matters

Kenmore dishwashers are often built with components shared across major manufacturers, so parts availability stays strong for high-failure items like pumps, valves, heaters, and rack hardware. Using the exact model number prevents ordering a look-alike part that will not mount correctly or plug in safely.

Quick safety note for installs and pull-outs

If you are removing the dishwasher to access parts, follow the installation guide steps for electrical, water, and drain connections; the guide also calls out keeping the unit level and secured in the cabinet opening.

Last updated: February 2026

Yes, repairing a Kenmore undercounter dishwasher like model 66513263K110 is usually worth it when the problem is a wear item (rack parts, hoses, valves) or a simple no-start issue; it is less cost-effective when multiple major components fail or the tub is damaged. Use the 66513263K110 owner's manual to compare symptoms to normal operation.

Quick decision checklist

• If the dishwasher is under 10 years old, repairs are typically the better value.
• If the repair is under about 50% of the cost of a comparable new dishwasher, repair usually makes sense.
• If you have leaks at the hose/valve, a targeted part replacement is often a straightforward fix.
• If it won’t drain, check for a clog first; then consider a drain pump.
• If it won’t fill, confirm the water supply is on; then consider the inlet valve.
• If it has multiple symptoms (no fill, no drain, no heat), plan for deeper electrical diagnosis.

Common repairs that are usually “worth it” on 66513263K110

These are frequent, contained repairs with predictable results:

• Replace a leaking or restricted inlet valve: dishwasher water inlet valve W11175771
• Fix a no-drain condition after clearing the drain path: dishwasher drain pump WPW10348269
• Restore cleaning performance by addressing filtration: dishwasher filter W10872845
• Repair rack issues (wheels, stops, adjusters) to prevent damage and improve loading

What to check before buying parts

The installation guide’s “does not operate” checks can save a service call:

• Confirm the breaker/fuse is OK.
• Make sure the door is fully closed and latched.
• Verify the cycle is set to start.
• Confirm the water supply is turned on.

Symptom	Most likely area	Typical next step
Won’t start	Power, latch, control	Verify breaker and latch; then diagnose controls
Won’t drain	Drain path, drain pump	Clear blockage; test/replace pump
Won’t fill	Supply, inlet valve	Confirm water on; replace valve if needed
Poor cleaning	Filter, spray arm	Clean filter; inspect spray arm

Why it matters

A focused repair keeps your Kenmore dishwasher running reliably and avoids the cost and hassle of replacement, especially when the issue is isolated to a single part like a valve, pump, or filter.

Last updated: February 2026

The model number for your Kenmore undercounter dishwasher is printed on the appliance’s model and serial tag. On Kenmore dishwashers like model 66513263K110, the tag is typically located along the inside edge of the door or on the tub frame where the door closes.

Where to look on the dishwasher

Check these common locations first (with the door open):

• Along the left or right inner door edge
• On the tub frame just inside the opening (top or side rail)
• Near the latch area on the inner door or tub lip
• Behind the lower access panel area (less common for the model tag)

What the model number looks like

Use the full model number exactly as shown on the tag; for this dishwasher it will read 66513263K110.

What you may see	What it means	What to do with it
Model	Identifies the exact dishwasher version	Use it to match parts and diagrams
Serial	Production code and date info	Helpful for service history
Type/Code	Internal manufacturing identifiers	Usually not needed for ordering

Why it matters

Kenmore 665-prefix dishwashers can have multiple versions that look similar. Using the exact model number ensures the replacement parts you choose (like a drain pump, water inlet valve, or rack components) fit and connect correctly.

Tips for reading the tag

• Wipe the label with a damp cloth to remove detergent film
• Copy the model number character-for-character (including letters like K)
• Take a clear photo before ordering parts

For diagrams and model identification details, use the 66513263K110 owner's manual.

Last updated: March 2026