Kenmore 66513882K800 dishwasher Parts

To reset the control on your Kenmore dishwasher model 66513882K800, we recommend using the built-in reset procedure: press CANCEL/DRAIN twice, then reselect your cycle and press START/RESUME. This clears the current cycle and resets the control logic. See the steps in the 66513882K800 owner's manual.

Reset options that work on 66513882K800

Use the method that matches what your dishwasher is doing.

• Stuck mid-cycle or acting erratic: press CANCEL/DRAIN twice
• You opened the door during a delay start: close the door and press START/RESUME again
• Buttons do not respond: check whether Control Lock is on (LOCK ON light)
• Dishwasher will not run: confirm the door is fully latched, then try the reset again

Step-by-step: reset the control (cycle reset)

1. Open the door slightly to stop the cycle; wait for spraying to stop.
2. Press CANCEL/DRAIN.
3. Press CANCEL/DRAIN a second time to reset the control.
4. Close the door; let it drain for about 2 minutes if needed.
5. Select a new cycle and options.
6. Close the door firmly and press START/RESUME.

If the controls are locked (Control Lock)

If the dishwasher seems “dead” but has power, the controls may be locked.

• Press and hold HEATED DRY for 4 seconds to toggle Control Lock
• When LOCK ON is lit, all buttons are disabled
• The door can still open and close while locked

Symptom	Most likely cause	What to do
Cancel/Drain runs but won’t start a new cycle	Door not fully closed	Close firmly, press START/RESUME
No buttons respond	Control Lock enabled	Hold HEATED DRY 4 seconds
Delay countdown stops after opening door	Start/Resume not pressed	Close door, press START/RESUME

Why it matters

A proper reset clears a stalled cycle and forces the electronic control to restart the wash sequence. It also helps you avoid repeated start failures that can look like a bad electronic control.

Last updated: January 2026

On Kenmore dishwasher model 66513882K800, you typically clear an error code by canceling the current cycle and resetting the control so it can recheck sensors and restart normally. The exact button sequence depends on your control panel, so we recommend following the steps in the 66513882K800 user manual.

Quick ways to clear an error code

Try these in order (stop when the code clears):

• Press CANCEL/DRAIN (or CANCEL) once; let the dishwasher drain completely.
• If the display still shows a code, press CANCEL/DRAIN again and wait 1 to 2 minutes.
• If the controls are unresponsive, check whether Control Lock is on; on this model family, Control Lock is commonly toggled by holding HEATED DRY for about 4 seconds.
• Turn power off at the breaker for 1 minute, then restore power.
• Start a short cycle and press START/RESUME after closing the door (some models require START/RESUME any time the door is opened).

If the code comes back right away

A repeating code usually means the dishwasher is detecting the same problem again. These checks fix the most common causes:

• Drain issue: Make sure the sink drain and garbage disposal inlet are clear; check for kinks in the drain hose.
• Water fill issue: Confirm the water shutoff valve is fully open.
• Overheating or drying problem: If dishes stay cold or wet, the heating circuit may be involved.
• Door not latching: Make sure the door closes firmly and the latch engages.

Common symptom-to-part mapping (when replacement is needed)

Symptom after reset	What it often points to	Example part for this model
Won’t drain, standing water	Drain pump or drain path restriction	Dishwasher drain pump WPW10348269
Poor drying, water not heating	Heating circuit problem	Dishwasher heating element W10518394
No fill or very slow fill	Water inlet valve or supply issue	Dishwasher water inlet valve WPW10158389

Why it matters

Clearing the code gets you running again, but the code is a clue. If it returns, using it to narrow the problem helps you avoid repeat shutdowns, incomplete draining, and poor wash or dry performance.

For code definitions and what each one means, use our Kenmore 665 model dishwasher error codes reference.

Last updated: January 2026

On Kenmore dishwasher model 66513882K800, error code F2E2 points to a user interface (keypad) communication problem, most often caused by a loose/dirty ribbon connector between the control panel and the electronic control, or a failing keypad/control.

What to check first (fast, common fixes)

• Reset power: turn the breaker off for 1 minute, then back on.
• Open the control panel and reseat the keypad ribbon connector (unplug, inspect, reconnect firmly).
• Look for corrosion, moisture, or detergent residue on the connector and pins; clean and dry before reconnecting.
• Check for pinched wiring at the door hinge area.
• Try each key; if multiple keys do not respond or act “stuck,” the keypad is typically the issue.

Parts that are commonly involved

F2E2 is usually tied to the control panel keypad or the main electronic control. If your troubleshooting points to the main control, the model-specific option we commonly see for this dishwasher is the electronic control WPW10285178.

Quick decision guide

What you observe	Most likely cause	What to do next
Code appears after cleaning or a spill	Moisture/contamination at connector	Dry, clean, reseat ribbon connector
Random beeping or keys activate by themselves	Keypad shorted	Replace the user interface/keypad assembly
Keys respond but code returns	Control not reading UI reliably	Inspect wiring; consider main control replacement

Why it matters

When the keypad and control cannot communicate, the dishwasher may not start, may stop mid-cycle, or may ignore button presses. Fixing the connection early can prevent repeat shutdowns and nuisance beeping.

Reference for your exact model

Use the 66513882K800 owner’s manual for the control panel layout, cycle selection, and any model-specific diagnostics or reset steps.

Last updated: January 2026