Installation guide
Owner’s manual
Error Codes
How do I reset my Kenmore dishwasher control board?
To reset the control on your Kenmore dishwasher model 66513882K800, we recommend using the built-in reset procedure: press CANCEL/DRAIN twice, then reselect your cycle and press START/RESUME. This clears the current cycle and resets the control logic. See the steps in the 66513882K800 owner's manual.
Use the method that matches what your dishwasher is doing.
- Stuck mid-cycle or acting erratic: press CANCEL/DRAIN twice
- You opened the door during a delay start: close the door and press START/RESUME again
- Buttons do not respond: check whether Control Lock is on (LOCK ON light)
- Dishwasher will not run: confirm the door is fully latched, then try the reset again
- Open the door slightly to stop the cycle; wait for spraying to stop.
- Press CANCEL/DRAIN.
- Press CANCEL/DRAIN a second time to reset the control.
- Close the door; let it drain for about 2 minutes if needed.
- Select a new cycle and options.
- Close the door firmly and press START/RESUME.
If the dishwasher seems “dead” but has power, the controls may be locked.
- Press and hold HEATED DRY for 4 seconds to toggle Control Lock
- When LOCK ON is lit, all buttons are disabled
- The door can still open and close while locked
| Symptom | Most likely cause | What to do |
|---|---|---|
| Cancel/Drain runs but won’t start a new cycle | Door not fully closed | Close firmly, press START/RESUME |
| No buttons respond | Control Lock enabled | Hold HEATED DRY 4 seconds |
| Delay countdown stops after opening door | Start/Resume not pressed | Close door, press START/RESUME |
A proper reset clears a stalled cycle and forces the electronic control to restart the wash sequence. It also helps you avoid repeated start failures that can look like a bad electronic control.
Last updated: January 2026
How to clear code on Kenmore dishwasher?
On Kenmore dishwasher model 66513882K800, you typically clear an error code by canceling the current cycle and resetting the control so it can recheck sensors and restart normally. The exact button sequence depends on your control panel, so we recommend following the steps in the 66513882K800 user manual.
Try these in order (stop when the code clears):
- Press CANCEL/DRAIN (or CANCEL) once; let the dishwasher drain completely.
- If the display still shows a code, press CANCEL/DRAIN again and wait 1 to 2 minutes.
- If the controls are unresponsive, check whether Control Lock is on; on this model family, Control Lock is commonly toggled by holding HEATED DRY for about 4 seconds.
- Turn power off at the breaker for 1 minute, then restore power.
- Start a short cycle and press START/RESUME after closing the door (some models require START/RESUME any time the door is opened).
A repeating code usually means the dishwasher is detecting the same problem again. These checks fix the most common causes:
- Drain issue: Make sure the sink drain and garbage disposal inlet are clear; check for kinks in the drain hose.
- Water fill issue: Confirm the water shutoff valve is fully open.
- Overheating or drying problem: If dishes stay cold or wet, the heating circuit may be involved.
- Door not latching: Make sure the door closes firmly and the latch engages.
| Symptom after reset | What it often points to | Example part for this model |
|---|---|---|
| Won’t drain, standing water | Drain pump or drain path restriction | Dishwasher drain pump WPW10348269 |
| Poor drying, water not heating | Heating circuit problem | Dishwasher heating element W10518394 |
| No fill or very slow fill | Water inlet valve or supply issue | Dishwasher water inlet valve WPW10158389 |
Clearing the code gets you running again, but the code is a clue. If it returns, using it to narrow the problem helps you avoid repeat shutdowns, incomplete draining, and poor wash or dry performance.
For code definitions and what each one means, use our Kenmore 665 model dishwasher error codes reference.
Last updated: January 2026
What is the code f2e2 on a Kenmore dishwasher?
On Kenmore dishwasher model 66513882K800, error code F2E2 points to a user interface (keypad) communication problem, most often caused by a loose/dirty ribbon connector between the control panel and the electronic control, or a failing keypad/control.
- Reset power: turn the breaker off for 1 minute, then back on.
- Open the control panel and reseat the keypad ribbon connector (unplug, inspect, reconnect firmly).
- Look for corrosion, moisture, or detergent residue on the connector and pins; clean and dry before reconnecting.
- Check for pinched wiring at the door hinge area.
- Try each key; if multiple keys do not respond or act “stuck,” the keypad is typically the issue.
F2E2 is usually tied to the control panel keypad or the main electronic control. If your troubleshooting points to the main control, the model-specific option we commonly see for this dishwasher is the electronic control WPW10285178.
| What you observe | Most likely cause | What to do next |
|---|---|---|
| Code appears after cleaning or a spill | Moisture/contamination at connector | Dry, clean, reseat ribbon connector |
| Random beeping or keys activate by themselves | Keypad shorted | Replace the user interface/keypad assembly |
| Keys respond but code returns | Control not reading UI reliably | Inspect wiring; consider main control replacement |
When the keypad and control cannot communicate, the dishwasher may not start, may stop mid-cycle, or may ignore button presses. Fixing the connection early can prevent repeat shutdowns and nuisance beeping.
Use the 66513882K800 owner’s manual for the control panel layout, cycle selection, and any model-specific diagnostics or reset steps.
Last updated: January 2026
