Kenmore 66515119K216 dishwasher Parts

On Kenmore dishwasher model 66515119K216, we typically find the model number on the rating label located just inside the door, along the tub frame edge. That same label usually also lists the serial number, which helps match the correct parts and manuals.

Where to look on the dishwasher

Check these common label locations first:

• Open the door and look along the left side of the tub opening (most common)
• Check the right side of the tub opening if you do not see it on the left
• Look along the top edge of the tub opening under the countertop lip
• Check the inner door edge near the latch area

What the label information means

The rating label usually includes more than just the model number.

Label item	What it’s used for
Model number	Ensures parts fit your exact dishwasher configuration
Serial number	Helps identify production series and compatible revisions
Electrical ratings	Confirms voltage and amperage requirements

Why it matters when ordering parts

Using the exact model number prevents common fit and compatibility problems.

• Kenmore 665-series dishwashers can use different pumps, hoses, and controls by sub-model
• A single digit or letter difference can change the correct drain pump or inlet valve
• The model number helps us match the correct diagrams and repair instructions

Helpful next steps

Once you find the label, we recommend:

• Write the model number exactly as shown (including all digits and letters)
• Compare it to the model shown on your 66515119K216 owner’s manual
• Use the model number when selecting parts like the dishwasher drain pump WPW10348269
• If you are troubleshooting an error, use the Kenmore 665 model dishwasher error codes reference

Why it matters

The model number is the fastest way to get the right Kenmore dishwasher parts, the right installation requirements, and the right troubleshooting steps for your exact build.

Last updated: January 2026

Kenmore dishwasher model 66515119K216 is a standard built-in dishwasher size: it fits a 24-inch-wide cabinet opening and uses an adjustable height range to match your countertop opening. For the exact cabinet opening and height-adjustment targets, use the 66515119K216 installation guide.

Cabinet opening size (what to measure)

Measure the opening where the dishwasher slides in, not the dishwasher door.

• Width: Most built-in Kenmore 665 dishwashers fit a 24-inch opening.
• Height: The installation guide shows a typical opening around 34 1/2 inches (87.6 cm), with adjustment using the leveling legs.
• Minimum height option: If the opening is tight, the guide notes the unit can fit into about 33 1/2 inches (85.1 cm) by removing the rear leveling legs and spacers.
• Depth: Depth varies by installation (door style and countertop overhang); confirm clearance in the dimensions section of the guide.

Height adjustment quick chart

These are the common height targets called out for this Kenmore 665 platform.

Cabinet opening height target	What you do	What to expect
~34 1/2 in (87.6 cm)	Adjust front and rear leveling legs evenly	Factory-preset baseline fit
~33 1/2 in (85.1 cm)	Remove rear leveling legs and spacers	Tighter fit; harder to move into place

Why it matters

Correct sizing prevents installation problems like a dishwasher that will not slide in, rubs the countertop, or sits unlevel (which can affect draining and wash performance). The 66515119K216 installation guide also shows the shaded utility-connection area so the drain hose, wiring, and water line do not interfere with fit.

Last updated: January 2026

For a Kenmore dishwasher model 66515119K216, the most reliable “hard reset” is to cancel the current cycle and reset the control: open the door to stop spraying, then press CANCEL/DRAIN twice, close the door within 3 seconds, and let it drain. See the 66515119K216 owner's manual for the exact button labels on your console.

Reset options (use the one that matches your situation)

• Stuck cycle or wrong cycle selected: Use CANCEL/DRAIN twice to reset the control, then reselect a cycle and press START/RESUME.
• Dishwasher won’t start and buttons don’t respond: Check for Control Lock; press and hold HEATED DRY for 3 seconds to toggle Lock off.
• You opened the door during a cycle or delay start: Close the door and press START/RESUME again to continue.

Step-by-step: reset the control (CANCEL/DRAIN)

1. Open the door slightly to stop the cycle; wait for spraying to stop.
2. Press CANCEL/DRAIN once, then press it a second time (this resets the control).
3. Close the door within 3 seconds.
4. Let the drain run until it finishes (the Cancel/Drain light typically turns off after about 2 minutes).

If it still won’t run after a reset

• Confirm the door is fully latched (a weak latch can mimic a “dead” control).
• Make sure Control Lock is off (HEATED DRY held 3 seconds).
• If the tub is full of water, check for a drain restriction; a failing pump can also prevent proper draining.
• If you hear humming but no draining, inspect the drain path and consider the dishwasher drain pump WPW10348269.

Quick reference table

Symptom	Best reset action	What to do next
Wrong cycle, stuck mid-cycle	CANCEL/DRAIN twice	Pick new cycle, press START/RESUME
Buttons disabled, “Lock” light on	Hold HEATED DRY 3 seconds	Start cycle normally
Delay start paused after door opened	Press START/RESUME	Let countdown continue

Why it matters

Resetting the control clears a stalled cycle and forces a fresh start sequence; checking Control Lock prevents unnecessary parts replacement when the dishwasher is simply locked.

Last updated: January 2026

On Kenmore dishwasher model 66515119K216, the most common problems are a no-start or blinking Start/Resume light, water left in the tub (won’t drain), poor drying, cycles that run too long, and hard-water residue or odors. Use the 66515119K216 owner's manual for model-specific troubleshooting.

Common symptoms and what usually causes them

• Won’t run or Start/Resume blinks: door not fully latched, cycle not selected, Sleep Mode active, or power issue.
• Water remains in tub or won’t drain: kinked drain hose, disposer knockout plug not removed, or a clog in the drain path.
• Detergent left in dispenser/tablet on tub bottom: dispenser blocked by dishes, or spray action restricted.
• Not drying well: rinse aid not used, option selection not matched to load, or water not hot enough.
• Hard-water film, spots, cloudy glassware, or odors: hard water, low rinse aid, too much detergent, or filters needing cleaning.

Quick checks we recommend first

• Close and latch the door; if the Start/Resume light blinks, press START/RESUME.
• Confirm the breaker is on and a cycle is selected.
• Inspect the drain hose for kinks; if connected to a disposer, confirm the inlet knockout plug is removed.
• Clean the filter area regularly; buildup causes odors and weak wash performance.
• Set incoming hot water to about 120°F (49°C) for better cleaning and drying.

Problem-to-fix guide

Problem	What you’ll notice	First fix to try
Won’t start / blinking lights	Lights blink, no wash action	Latch door, press START/RESUME, reselect cycle
Won’t drain	Standing water after cycle	Clear drain path, unkink hose, check disposer plug
Spots/cloudiness	Film on glasses, white residue	Use rinse aid, adjust detergent, address hard water

When a part is a strong suspect

• Draining issues: dishwasher drain pump WPW10348269
• Poor cleaning or weak spray: dishwasher spray arm WPW10491331
• Won’t fill: dishwasher water inlet valve W11175771

Why it matters

Dishwashers rely on correct water fill, strong circulation, and a clear drain path. Small issues like loading interference, dirty filters, or a kinked drain hose can mimic bigger failures and create long cycles, odors, and poor results.

Last updated: January 2026