Craftsman 316380700 chainsaw Parts

On the Craftsman gas chainsaw model 316380700, the model number is typically printed on the product identification label or ID tag on the saw body. We use that model number to match the correct parts list, operator instructions, and safety specifications.

Where to look on the saw

Check these common label locations first (clean off oil and sawdust so the print is readable):

• On the rear handle area near the trigger
• On the starter housing (recoil starter side)
• Near the fuel tank or oil reservoir area
• On the crankcase or main housing near the bar mount
• On a sticker or metal tag under the top cover/air filter cover

Quick tips to read the label

If the label is dirty, faded, or partially damaged, these steps usually help:

• Wipe with a dry rag first, then use a small amount of mild cleaner
• Use a flashlight at an angle to make faint printing easier to see
• Look for “Model No.” followed by 316.380700 or 316380700
• Write down the full model number before ordering parts like a spark plug or air filter

Why it matters

The model number ensures we match the correct bar/chain specs and service parts for your exact saw. For example, the operator manual for this model lists a 16-inch guide bar, 3/8-inch chain pitch, and 0.050-inch chain gauge, which affects what replacement cutting components fit safely.

Model number vs. part number (what to record)

What you’re looking at	Example	What it’s used for
Model number	316380700	Identifies the exact chainsaw version
Part number	753-08107	Identifies a specific replacement part

For diagrams and the official identification details for this saw, use the 316380700 operator’s manual.

Last updated: January 2026

For your Craftsman gas chainsaw model 316380700, the serial number is typically printed on a model and serial tag on the saw body. We use that serial number to identify the exact production run so you can match the correct parts list and specifications in the 316380700 operator’s manual.

Where to find the serial number on a gas chainsaw

Check these common tag locations first (clean off oil and sawdust so the label is readable):

• On the crankcase or engine housing near the starter (recoil) side
• On the rear handle area near the throttle trigger
• Under or near the air filter cover
• Near the bar mount area (clutch cover side)
• On the bottom of the saw body near the fuel and oil tanks

How to look it up and use it

Once you have the serial number, use it to confirm you are ordering parts that match your exact unit configuration.

• Write down the model number (316380700) and the full serial number
• Compare the serial number format to what’s shown in the 316380700 operator’s manual
• Use the serial number when cross-checking parts like the air filter, spark plug, and carburetor
• If the tag is damaged, look for a second label or a stamped number on the housing

Quick checklist: model number vs. serial number

Item	What it tells you	Example
Model number	The product family and design	316380700
Serial number	The specific unit and production run	Varies by unit

Why it matters

Chainsaws can have small running changes during production. Using the serial number helps prevent ordering a part that looks similar but does not fit or perform correctly (especially for fuel system and ignition components).

Last updated: January 2026

For the Craftsman gas chainsaw model 316380700, 40:1 is the correct and better mix because that is the specified fuel-to-oil ratio for this 2-cycle engine. Using 50:1 reduces oil in the mix and can increase wear and overheating risk compared with the required 40:1. See the 316380700 operator's manual.

What to use for model 316380700

Use a 40:1 fuel/oil ratio (40 parts gasoline to 1 part 2-cycle oil).

• Use fresh, clean unleaded gasoline
• Use quality 2-cycle engine oil (air-cooled, if specified on the oil bottle)
• Mix in an approved fuel container, not in the fuel tank
• Shake the container before each refuel to re-blend the mix
• Do not “tune” the ratio leaner (like 50:1) to reduce smoke; keep 40:1

Quick mix chart (common batch sizes)

Gasoline amount	40:1 oil needed	50:1 oil needed (not recommended for this model)
1 gallon	3.2 oz	2.6 oz
2 gallons	6.4 oz	5.1 oz
5 liters	125 mL	100 mL

What happens if you run 50:1 in a saw that needs 40:1

Running 50:1 in a 40:1 engine means less lubrication. Common results include:

• Hotter running temperatures
• Faster piston and cylinder wear
• Scuffed piston or loss of compression over time
• Hard starting and rough running under load

Why it matters

On a 2-cycle chainsaw, the oil in the fuel mix lubricates the crankshaft bearings, piston, and cylinder. The 316380700 is designed around 40:1, so keeping that ratio protects the engine and helps it deliver consistent power.

Last updated: January 2026

The model number for this Craftsman gas chainsaw is 316.380700 (often written without the dot as 316380700). You’ll see it printed on the unit’s model tag and on the cover of the 316380700 operator's manual.

Where to find the model number on the saw

Look for the model tag in common ID-label locations for this style of Craftsman chainsaw:

• On the rear handle area near the trigger
• On the starter housing (recoil starter side)
• Near the bar and chain cover area
• On the crankcase or chassis label plate

Why the “358” number you may see is different

Some Craftsman chainsaws use model numbers that start with 358 (a different Craftsman model family). For the chainsaw on this parts page, the correct identifier for ordering parts and using the right documentation is 316.380700.

What you’re looking at	What it means	What to use for parts
316.380700 (or 316380700)	This specific Craftsman chainsaw model	Use this
358.xxx	A different Craftsman chainsaw model line	Do not use for this saw

Why it matters

Using the exact model number helps us match the correct parts (like the guide bar, saw chain, fuel system parts, and ignition components) and the correct specifications for safe operation.

Last updated: January 2026