Kenmore Elite 11027087602 washer Parts

The exact tub capacity (cubic feet) for Kenmore Elite washer model 11027087602 is listed in the product specifications section of the 11027087602 owner's manual. If you do not see it there, use the measurement method below to estimate capacity accurately.

How to find the official capacity for model 11027087602

• Check the Specifications or Product data section in the 11027087602 owner's manual
• Look for terms such as capacity, basket volume, or tub volume
• If your washer has a tech sheet stored inside the cabinet (often behind the control panel or along an interior side wall), it may list capacity as well

How to estimate washer capacity (cubic feet)

If you want a practical estimate, we use this method:

1. Measure the inside of the wash basket:
   • Diameter (inches)
   • Depth (inches) from the bottom to the top rim (not the lid)
2. Calculate basket volume:

Step	What to do	Formula
1	Find radius	radius = diameter ÷ 2
2	Find cubic inches	volume = π × radius² × depth
3	Convert to cubic feet	cubic feet = cubic inches ÷ 1728

Quick example

If the basket is 20 inches wide and 16 inches deep:

• radius = 10
• volume ≈ 3.1416 × 10² × 16 = 5,026 cubic inches
• capacity ≈ 5,026 ÷ 1,728 = 2.9 cubic feet

Typical capacity range (for context)

Most Kenmore top-load washers in this style land in a broad range:

• About 3.0 to 4.5 cubic feet for many high-efficiency top-load designs
• Larger “oversize” models can be higher

Why it matters

Capacity helps you choose the right cycle and load size. Overloading can reduce cleaning performance and increase vibration, which can contribute to wear on suspension and spin components.

Last updated: January 2026

To force-drain a Kenmore Elite washer model 11027087602, we recommend canceling the cycle and running a Drain/Spin (or Spin Only) cycle first. If the washer will not drain, remove power and manually empty water through the drain hose or pump area, then clear the clog.

Fast ways to get the water out

• Try a Drain/Spin cycle: Press Pause/Cancel (or Stop) once, then select Drain/Spin and start.
• Power reset: Unplug the washer for 1 minute, plug it back in, then try Drain/Spin again.
• Manual drain (safest approach): Unplug the washer, then lower the drain hose into a shallow pan or floor drain to let water siphon out.
• Check for a kinked hose: Straighten the drain hose and confirm it is not crushed behind the cabinet.

What to check if it still will not drain

A no-drain condition is usually a blockage, a failed drain pump, or a lid lock issue.

• Look for coins, socks, lint, or debris restricting the drain path
• Confirm the standpipe or laundry tub is not backing up
• Listen for the drain pump: a loud hum with no water movement often points to a jammed pump
• If the lid will not lock, the washer may refuse to drain or spin; inspect the lid lock

Common parts related to no-drain symptoms

Symptom	Most likely area	Example part for this model
Hums but will not pump	Drain pump jammed or failed	Pump-water W10536347
Will not spin/drain, lid error	Lid lock not engaging	Washer lid lock WPW10619844
Slow drain or overflow at standpipe	Drain hose/house drain issue	Drain hose routing and standpipe height (see guide)

Drain hose setup details that affect draining

Improper drain hose routing can cause slow draining or siphoning. Our installation instructions call out using the hose form and securing the hose properly; see the installation guide for the correct routing and securing method.

Why it matters

Forcing a drain without fixing the cause can lead to repeat stoppages, wet loads, and pump damage. Clearing the drain path and confirming correct drain hose installation restores normal drain and spin performance.

Last updated: January 2026

To hard reset a Kenmore Elite washer model 11027087602, we power-cycle it to clear a temporary control glitch: turn the washer off, disconnect power for a short time, then restore power and restart a cycle. For normal stopping and restarting, use the STOP and START buttons as described in the 11027087602 owner's manual.

Reset steps (safe, no tools)

• Press POWER to turn the washer off.
• Unplug the washer (or switch the breaker off).
• Wait 1 minute.
• Plug the washer back in (or turn the breaker on).
• Press POWER, select a cycle, then press START.

If the washer still will not start

These checks solve most “won’t run” complaints after a reset.

• Confirm the lid is fully closed; the washer will not start with the lid open.
• Press STOP once to pause and unlock, then press START to restart.
• If the Lid Lock light stays on or the lid will not lock, inspect the lid strike area for detergent buildup or a misaligned lid.
• Verify the outlet is a grounded 3-prong outlet and avoid extension cords.
• If the tub is off-balance and the washer stops mid-cycle, redistribute the load and try again.

When a reset points to a part problem

If power-cycling works only briefly, the issue is often a lid-lock sensing problem.

Symptom	What it usually means	Common next step
Won’t start, lid won’t lock	Lid lock not engaging or not being sensed	Check/replace washer lid lock WPW10619844
Stops and unlocks repeatedly	Intermittent lid lock or wiring connection	Inspect lid lock connector and harness routing

Why it matters

A hard reset clears a stuck control state, but it does not fix an underlying failure. If the washer repeatedly needs resetting, focusing on lid-lock operation and safe power supply prevents repeat shutdowns and protects the control.

Last updated: January 2026