Kenmore 11021102012 washer Parts

Yes. Kenmore top load washer model 11021102012 uses a drain pump system that can trap debris; many owners treat the pump cleanout area and drain path as the washer’s “filter.” We recommend checking the drain hose and pump area first when you have draining, odor, or lint issues.

Where the “filter” is on this washer

Most top load washers like Kenmore 11021102012 do not have a simple, front twist-out lint filter. Instead, filtering happens in the drain system.

Common places to check:

• The drain pump inlet area (where small items can collect)
• The drain hose for clogs or kinks
• The laundry tub or standpipe for slow-drain restrictions
• The tub ring area for trapped lint and residue

How to check it safely (quick steps)

Use the safety and access guidance in the 11021102012 installation guide before moving the washer.

• Unplug the washer (grounded outlet only; no extension cord)
• Turn off hot and cold water faucets
• Pull the washer forward enough to access the drain hose
• Inspect the drain hose for kinks, crushing, or blockage
• If draining is still slow, plan to inspect the pump for debris

Parts that commonly relate to “filter” symptoms

If the washer will not drain, drains slowly, or leaves water behind, these parts are often involved:

Symptom	Most likely area	Example part for this model
Won’t drain / hums	Drain pump jammed or failed	Washer drain pump assembly WPW10276397
Drains but siphons back	Drain hose/standpipe setup	Washer drain hose W11244231
Stops mid-cycle / won’t spin	Lid not locking	Washer lid lock assembly W10404050

Why it matters

A restricted drain path acts like a clogged filter: it can cause standing water, odors, poor spin performance, and error conditions. Keeping the drain hose routing correct and the pump area clear helps protect the gear case, drive belt, and motor from extra strain.

Last updated: February 2026

The exact tub capacity (cubic feet) for Kenmore washer model 11021102012 is listed in the product specifications section of the documentation; we use the 11021102012 owner's manual as the best source for the precise number for your specific washer.

How to find the cubic feet in the documentation

Capacity is usually shown as “capacity,” “tub volume,” or “cu. ft.” in the specs.

• Open the 11021102012 owner's manual and look for a Specifications section
• Check the first few pages and the back pages for a model specs table
• If you only see installation details, check the Use and Care portion (often separate from install steps)
• If your manual lists multiple similar models, match the exact model number 11021102012

Typical capacity range (for context)

Most Kenmore top-load washers in this style commonly fall into a mid-size capacity range. Use this as a quick planning estimate until you confirm the exact spec in the manual.

What you need it for	Typical planning number	Why
Replacing with a similar washer	3.5 to 4.5 cu. ft.	Helps keep load size and cycle times similar
Laundry room fit and hookups	Capacity does not change exterior size much	Dimensions and clearances matter more than cu. ft.
Comparing performance	Higher cu. ft. usually fits bulkier loads	Comforters and bedding need more space

Why it matters

Knowing the cubic feet helps us size loads correctly (better cleaning and spin-out), compare replacement models, and set expectations for bulky items like bedding.

Related installation note (often confused with capacity)

The installation guide focuses on clearances and setup, not tub volume. For example, it notes the washer can be installed with 0 in. side clearance (with additional space recommended for service and noise reduction). See the 11021102012 installation guide for spacing and hookup requirements.

Last updated: February 2026

For Kenmore washer model 11021102012, we identify the model number on the appliance’s rating label, not on the control buttons. On top-load washers like this one, the label is typically under the lid, on the back of the control panel, or on the cabinet near the bottom edge; the serial number is on the same label.

Where to look on a Kenmore top-load washer

Check these common label locations first:

• Under the lid opening (around the tub rim)
• On the back of the control panel (rear of the console)
• On the left or right side of the main cabinet near the bottom
• On the rear panel of the washer cabinet

If you’re using the model number for parts lookup, write it exactly as shown, including all digits: 11021102012.

What the label usually shows

Most Kenmore washer ID labels include:

• Model number (used to match parts diagrams)
• Serial number (used for manufacturing date and service history)
• Electrical ratings (volts/amps)
• Sometimes installation notes fields (model and serial) referenced in the documentation

Use the 11021102012 installation guide to see where Kenmore expects you to record the model and serial number during setup.

Quick check: model number vs. serial number

Item	What it’s for	Example format
Model number	Correct parts and manuals	11021102012
Serial number	Production tracking and service	Letters and numbers

Why it matters

Kenmore model numbers can look similar across different washer platforms, and even a one-digit difference can change the correct lid lock, drive belt, or drain pump. Matching the exact model number prevents ordering the wrong replacement part.

Last updated: February 2026

To reset a Kenmore top-load washer model 11021102012, we recommend doing a simple power reset first: turn the washer off, unplug it for 1 minute, then plug it back in and select a cycle to test. This clears many control glitches and stuck states.

Quick reset steps (most common)

• Press Power/Cancel to stop the cycle.
• Unplug the washer (or switch the breaker off).
• Wait 60 seconds.
• Plug back in (or turn breaker on).
• Select a normal cycle and press Start to confirm operation.

If it still will not start or unlock

A “reset” will not fix a condition the control is protecting against (lid not locked, drain issue, or an out-of-balance stop). Check these items next:

• Make sure the lid is fully closed; listen for the lock click.
• Verify the washer is plugged into a grounded 3-prong outlet (no extension cord).
• If the tub is full of water, run Drain/Spin and confirm water pumps out.
• Confirm water faucets are fully on.
• If the washer is new or recently moved, remove all shipping materials and confirm it is level.

What to check based on the symptom

Symptom after reset	Most likely cause	What to do next
Won’t start, lid won’t lock	Lid lock problem	Inspect the strike area; consider replacing the washer lid lock assembly W10404050.
Hums but won’t agitate/spin	Drive system issue	Check belt condition; replace the washer drive belt WPW10006384 if worn or broken.
Won’t drain	Pump or drain path restriction	Check hose for kinks; inspect pump inlet; replace the washer drain pump assembly WPW10276397 if seized.

Why it matters

Resetting restores normal control operation, but the washer will still stop if it senses an unsafe condition (like an unlocked lid) or a mechanical problem (like a slipping belt). Fixing the root cause prevents repeat shutdowns and incomplete cycles.

For model-specific operating steps and cycle behavior, follow the 11021102012 owner’s manual.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For your Kenmore model 11021102012, lifespan depends most on installation, load habits, and how quickly you address wear items like the drive belt, lid lock, and drain pump; our 11021102012 installation guide helps you start with the right setup.

Typical lifespan and what changes it

Most washers reach the 10 to 15 year range when they are level, have proper water pressure, and are not routinely overloaded.

• Overloading and frequent heavy loads increase strain on the drive system
• An unlevel washer increases vibration and speeds up wear on the gear case and suspension
• Poor draining (slow drain, standing water) overworks the drain pump
• Lid lock problems can stop cycles and cause repeated restarts
• Hard water and excess detergent can leave residue that affects performance

Signs it is nearing end of life

If you see several of these at once, repairs can add up quickly.

Symptom	Common cause	What we check first
Loud squeal or burning rubber smell	Belt slipping	Washer drive belt WPW10006384
Won’t spin or agitates inconsistently	Shift/drive issue	Washer actuator WPW10006355
Won’t start or won’t unlock	Lid lock failure	Washer lid lock assembly W10404050
Water left in tub	Drain restriction or pump wear	Washer drain pump assembly WPW10276397

How we help you extend the life of model 11021102012

These steps reduce stress on the motor, pulley, and gear case.

• Keep the washer level on a solid floor; avoid installing on carpet
• Use the right amount of detergent and avoid repeated “extra rinse” unless needed
• Wash bulky items in smaller loads to prevent off-balance spinning
• Check pockets and use garment bags to reduce debris reaching the pump
• Fix small issues early (belt noise, slow drain, lid lock clicking)

Why it matters

A washer that is installed correctly and kept level runs quieter, drains faster, and puts less load on high-cost components (like the gear case and drive motor). That is the difference between a routine part replacement and a major repair.

Last updated: February 2026

Kenmore is a brand name, so replacement parts for Kenmore washer model 11021102012 are typically manufactured by the same major companies that build Kenmore-designed appliances and components (most commonly Whirlpool-family suppliers, and sometimes other large OEMs). The most reliable way to confirm the correct maker is to match the exact part number and model listing in the 11021102012 installation guide.

How to tell who made your specific Kenmore part

Kenmore parts sourcing varies by model and by component, so we recommend identifying the part by its exact part number or part ID.

• Find the model tag and confirm it reads 11021102012
• Use the parts diagram to locate the exact component name (for example, lid lock, drain pump, drive belt)
• Match the part number and part ID exactly when ordering
• If you are replacing a drive system component, verify related wear items at the same time (belt, pulley, actuator)
• Use the documentation to confirm any installation notes, tools, and safety steps

Common examples for this model

These are examples of model-matched parts that are commonly produced by Whirlpool-family suppliers for Kenmore 110-series washers:

What you are replacing	Example model-matched part	What it does
Drive belt	Washer drive belt WPW10006384	Transfers motor power to the drive system
Lid lock	Washer lid lock assembly W10404050	Helps keep the lid locked during spin for safety
Drain pump	Washer drain pump assembly WPW10276397	Pumps water out during drain/spin

Why it matters

Kenmore branding can hide the original manufacturer, but the correct fit and function comes from matching the exact part number to model 11021102012. That prevents ordering a similar-looking part that mounts differently, uses a different connector, or has different calibration.

Quick ordering checklist

• Confirm the full model number: 11021102012
• Identify the part by diagram location and name
• Match the part ID and part number exactly
• Review required tools and safety steps in the 11021102012 installation guide

Last updated: February 2026