Kenmore 66513255K113 undercounter dishwasher Parts

Yes. We still carry replacement parts for many Kenmore dishwashers, including Kenmore model 66513255K113; the key is matching parts by the full model number so you get the correct fit and connections. For diagrams, part lookups, and installation notes, use the 66513255K113 owner's manual and 66513255K113 installation guide.

How to make sure you order the right part

Use these checks before you buy:

• Confirm the full model number is 66513255K113 (from the rating label on the tub frame).
• Match the symptom to the system involved (drain, fill, wash, heat, door).
• Compare the part description and mounting style (hose ends, electrical terminals, bracket locations).
• If you are replacing a leak-related part, inspect nearby seals and clamps at the same time.
• If the dishwasher is hard-wired, plan to shut off power at the breaker before servicing.

Common Kenmore 66513255K113 parts customers replace

These are frequent wear items and failure points on this platform:

Symptom	Likely part to check	Example part for this model
Won’t drain, water left in tub	Drain pump or drain hose	Dishwasher drain pump WPW10348269 or dishwasher drain hose 8269144A
Not filling or fills slowly	Water inlet valve	Dishwasher water inlet valve W11175771
Poor cleaning, weak spray	Spray arm, filter	Dishwasher spray arm WPW10491331 or dishwasher filter W10872845
Door leaks at bottom	Lower door seal	Seal WPW10497235

Why the model number matters (especially for Kenmore)

Kenmore dishwashers are built across multiple manufacturing platforms. Even when parts look similar, small differences in wiring plugs, hose routing, or mounting tabs can change compatibility. Using 66513255K113 ensures you land on the correct OEM-style replacement.

Installation and fit tips we recommend

The installation guide for this model calls out several fit and safety details that affect parts and performance:

• Keep water lines, drain lines, and wiring routed so they do not contact the motor or legs.
• Maintain clearance so the motor does not touch the floor; do not install over carpet.
• Corner installs need about 2 inches of clearance between the door and adjacent wall/cabinet.
• Level the dishwasher front-to-back and side-to-side; use shims if the opening floor is uneven.
• After reconnecting power, run the shortest cycle and verify water enters the tub within the first couple minutes.

Last updated: February 2026

On a Kenmore dishwasher, an E25 code points to a drain problem, most often a blocked drain pump area or an issue with the drain path that prevents water from pumping out normally. For model 66513255K113, start by checking the filter, sump area, and drain hose routing shown in the 66513255K113 installation guide.

What to check first (fast, no tools)

• Cancel the cycle and let the unit try to drain; listen for the drain pump running.
• Remove standing water (if needed) so you can inspect the bottom of the tub.
• Clean the filter and check the sump area for labels, glass, food, or twist ties.
• Verify the drain hose is not kinked or crushed behind the dishwasher.
• Confirm the drain connection is above the house drain trap and at least 20 inches above the floor (a high loop or air gap helps prevent backflow).

Parts that commonly cause E25 symptoms

If the drain path is clear but the dishwasher still will not drain, these parts are common suspects:

Symptom	Most likely cause	Example part for 66513255K113
Hums but drains slowly or not at all	Drain pump jammed or failing	Dishwasher drain pump WPW10348269
Drains sometimes, sometimes not	Partial blockage in hose or disposer inlet	Dishwasher drain hose (inspect routing)
Drains but water returns to tub	Missing high loop/air gap, improper connection height	Installation correction (not a part)

Why correct drain hose routing matters

A correctly routed drain hose prevents dirty sink water from flowing back into the tub and reduces drain errors. The installation instructions for this model specify connecting the drain hose to a waste tee or disposer inlet above the drain trap and at least 20 inches above the floor; a high loop under the counter or an air gap is recommended.

Safety and quick reset tip

• Turn off power at the breaker before accessing wiring or removing the dishwasher.
• If the dishwasher does not operate after checks, confirm the door is fully latched and the breaker is on; these are standard first checks listed in the installation instructions.

Last updated: February 2026

Water standing in the bottom of your Kenmore dishwasher model 66513255K113 almost always points to a draining problem: a clogged filter area, a restricted drain hose, or a drain pump that is jammed or failing. We recommend checking the easy blockages first, then testing the drain components.

Quick checks (most common fixes)

• Cancel the cycle and let the dishwasher try to drain; listen for the drain pump running.
• Remove the lower rack and check the sump area for food, labels, glass, or bones.
• Clean the filter and any screens; rinse under hot water and scrub off grease.
• Inspect the drain hose routing under the sink for kinks, crushing, or a low spot that traps water.
• If connected to a garbage disposal, confirm the disposal inlet knockout plug was removed.
• Check the sink drain or disposer for a clog that can back up into the dishwasher.

Parts that commonly cause standing water

If the hose and filter area are clear, the issue is usually in the drain path components.

Symptom	Most likely cause	What we do next
Hums but little or no draining	Drain pump jammed or worn	Inspect and replace the dishwasher drain pump WPW10348269 if the impeller is damaged
Drains slowly, water returns	Drain hose restricted or poor routing	Verify high loop/air gap and replace a damaged hose
Wash water looks dirty, debris recirculates	Filter or sump restriction	Clean filter area; replace the dishwasher filter W10872845 if cracked or warped

Why it matters

Standing water can cause odors, poor cleaning, and can strain the pump and motor over time. Restoring proper drain flow also helps prevent dirty water from re-entering the tub.

Model-specific tips from the documentation

During installation, correct drain hose placement and routing is critical; the install instructions call out checking the water line and drain hose position before finalizing the install. Use the 66513255K113 installation guide to confirm the drain hose is routed correctly and not pinched.

Last updated: February 2026