Owner’s manual
Error Codes
What size is Kenmore refrigerator model 79569009900?
Kenmore refrigerator model 79569009900 is a bottom-freezer design; for fit planning, most Kenmore 795 bottom-mount units are about 33 inches wide, 30 to 34 inches deep, and 66 to 70 inches tall. For the exact cabinet and door-clearance dimensions for your unit, use the 79569009900 owner's manual.
How to measure your refrigerator correctly
Use a tape measure and record all three dimensions; then compare to your opening.
- Measure width at the widest point (usually the cabinet, not the handles).
- Measure height from floor to top of cabinet; include hinge cover if it sits higher.
- Measure depth in two ways: cabinet only, and to the front of the doors/handles.
- Check door swing and drawer pull-out clearance for the bottom freezer.
- Confirm your doorway width; many bottom-freezer models need door removal if the opening is tight.
Space and clearance guidelines (typical)
These clearances help airflow and make doors and drawers operate normally.
| What to allow | Typical amount | Why it matters |
|---|---|---|
| Side clearance | 1/8 to 1/2 inch each side | Prevents rubbing and vibration |
| Top clearance | 1 inch | Helps ventilation and leveling |
| Rear clearance | 1 to 2 inches | Protects water line and airflow |
Why it matters
Correct sizing prevents installation headaches like doors that cannot open fully, a freezer drawer that hits an island, or poor airflow that can cause warm temperatures and longer compressor run times.
Related help
If you need to remove doors to get the refrigerator through an entrance (commonly under about 35 inches), follow the step-by-step procedure and tool list in the 79569009900 owner's manual.
Last updated: January 2026
Is top mounted refrigerator better than bottom mounted?
A top-mount refrigerator is usually the better pick for lowest cost and simple reliability, while a bottom-mount (like Kenmore 79569009900) is usually better for everyday convenience because fresh food sits at eye level. The “better” choice depends on how you shop, cook, and use freezer space.
Quick comparison: top-mount vs bottom-mount
| Feature | Top-mount (freezer on top) | Bottom-mount (freezer on bottom) |
|---|---|---|
| Fresh food access | You bend more | You bend less |
| Freezer access | Easier | Harder (often a drawer) |
| Organization | Simple shelves | Often better separation and bins |
| Typical price | Lower | Higher |
| Typical efficiency | Often very good | Varies by design and features |
When a top-mount is the better choice
- You want the lowest upfront cost.
- You use the freezer more than the refrigerator.
- You prefer a simpler layout with fewer moving parts (no freezer drawer slides).
- You want a lighter door load (less chance of door sag over time).
When a bottom-mount is the better choice (like 79569009900)
- You use fresh food most and want it at comfortable reach.
- You like better visibility of refrigerator shelves and crisper areas.
- You want a freezer drawer that can hold wider items (depending on basket layout).
- You are willing to keep door seals and alignment in good shape for best performance.
Why it matters
Refrigerators cool best when doors close and seal correctly and airflow is not blocked. Our Kenmore bottom-mount designs rely on proper air circulation between compartments and correct door closing and alignment for stable temperatures and fewer moisture issues. For model-specific use and setup details, follow the 79569009900 owner's manual.
Last updated: January 2026
What water filter fits my Kenmore fridge?
For Kenmore bottom-mount refrigerator model 79569009900, the correct water filter is the one specified for this exact model in the 79569009900 owner's manual. If your refrigerator is connected to a water supply, using the correct filter helps protect water taste and flow and reduces the chance of clogging.
How to identify the right filter for 79569009900
We match filters by the refrigerator’s exact model and filter housing style. Use these checks before ordering:
- Confirm the model number is 79569009900 (on the rating label inside the fresh food section)
- Check whether your unit is configured “with a water filter” (some versions use an internal filter; others use an inline filter)
- Look at the filter location (typically inside the fresh food compartment or in the base grille area)
- Match the filter’s shape and locking style (push-in, quarter-turn, or twist-lock)
- Replace the filter if you notice slow dispensing, odd taste/odor, or reduced ice production
Water pressure requirements (why filter choice and condition matter)
This model’s water system needs adequate pressure, especially when a filter is installed.
| Setup | Typical required water pressure | What you may notice if too low |
|---|---|---|
| With a water filter | 40 to 120 PSI | Slow fill, weak dispenser flow, small/slow ice |
| Without a water filter | 20 to 120 PSI | Better flow, but less protection from sediment |
If you have taste or odor in ice or water
The manual notes that minerals in the water supply can cause off-taste or odor; filtration is a common fix.
- Discard the first few batches of ice after installation or filter changes
- Throw away old ice that has been stored too long
- Wrap foods tightly to prevent odor transfer to ice
- Clean the ice bin and interior surfaces
- If your water has sulfur or heavy minerals, install or replace the filter on schedule
Why it matters
A correctly matched, regularly replaced refrigerator water filter helps maintain water quality and keeps the water valve and icemaker supply path from plugging with sediment.
Last updated: January 2026
What does DH mean on Kenmore Elite refrigerator?
On Kenmore model 79569009900, DH typically indicates a defrost heater (defrost) problem. The refrigerator is detecting that the defrost system is not warming the evaporator as expected, which can lead to frost buildup and poor cooling. Use the 79569009900 owner's manual troubleshooting section to confirm the exact display behavior for your unit.
What you’ll usually notice when DH shows
- Frost or ice building up on the freezer back wall
- Refrigerator section warming up even though the freezer seems cold
- Evaporator fan noise changing (fan hitting ice) or airflow getting weak
- Water leaking or refreezing from a clogged defrost drain
- Temperature swings after a power interruption
Quick checks we recommend (safe, no tools)
- Power reset: Unplug for 5 minutes, then restore power and monitor for 24 hours.
- Check door closure: Make sure doors seal fully and are not held open by bins or food.
- Look for heavy frost: If the freezer rear panel is heavily frosted, the defrost system is the likely cause.
- Check for puddles/ice: Ice on the freezer floor often points to a drain issue.
Parts commonly involved in a DH/defrost-heating issue
If the freezer panel is frosted over, these are the most common suspects:
- Defrost sensor or temperature sensor (helps the control know when to heat)
- Defrost heater circuit (heater, wiring, connectors)
- Main control board (may not be sending power to the heater)
- Defrost drain path (ice blockage can mimic defrost problems)
For this model, a common defrost-related component is the refrigerator defrost sensor assembly 6615JB2005C.
What to test next (technician-level)
Because live-voltage checks may be required, we recommend a qualified technician for these steps:
| Check | What it tells you | Typical outcome if failed |
|---|---|---|
| Heater circuit continuity | Whether the heater path is intact | Open circuit indicates a heater/wiring issue |
| Sensor resistance (cold vs warm) | Whether the sensor reports temperature correctly | Out-of-range readings indicate a bad sensor |
| Control output to heater during defrost | Whether the board is driving the heater | No output points to control or wiring |
Why it matters
A DH/defrost-heating problem can quickly reduce airflow across the evaporator, causing warm temperatures, ice buildup, and water leaks. Addressing it early helps protect food temperatures and prevents repeated icing.
Last updated: January 2026
