Kenmore 79641379210 washer Parts

For Kenmore washer model 79641379210, the most reliable reset is a power reset: unplug the washer (or switch off the breaker) for about 1 to 5 minutes, then restore power and start a cycle. This clears many temporary control and error-code glitches.

Quick reset steps (recommended)

• Press Power to turn the washer off.
• Unplug the power cord (or turn the circuit breaker off).
• Wait 1 to 5 minutes.
• Restore power.
• Press Power, then run a Rinse/Spin or a short cycle to confirm normal operation.
• If the control panel is unresponsive, repeat the reset with a full 5-minute power-off.

If the washer still will not run

These checks fix the most common “won’t start” situations after a reset:

• Confirm the door is fully closed and latching; a door lock issue can stop the cycle.
• Make sure the washer is not in Control Lock/Child Lock mode (see the 79641379210 owner’s manual).
• Verify both water supply valves are fully open and inlet hoses are not kinked.
• Reduce the load size and redistribute items; severe imbalance can prevent spin.
• If an error code returns, use the code list to target the right system.

Error codes: what to do next

If you see a code after resetting, use the code guidance first, then reset again after correcting the cause.

What you see	What it usually points to	What we do first
Drain-related code or no draining	Drain path or pump issue	Clean the drain filter, check the drain hose
Fill-related code or no water	Water supply or inlet valve issue	Check valves, screens, hose kinks
Unbalanced load code	Load distribution or suspension	Rebalance load, run a spin cycle

For code-specific help, use Kenmore 796 front load washer error codes.

Why it matters

A reset clears the control’s temporary memory, but it does not fix a mechanical problem like a clogged drain, a failing pump, or a door that is not locking. Pairing the reset with quick checks prevents repeat shutdowns and protects the drive system.

Last updated: February 2026

To identify your Kenmore washer model, find the model/serial tag on the washer cabinet and match the full model number exactly (for example, 79641379210). On many front-load Kenmore washers, the tag is inside the door opening or on the door jamb; confirm the exact location in the 79641379210 owner's manual.

Where to look on Kenmore washers

Check these common tag locations (the label is usually a sticker or metal plate):

• Behind the washer door, on the door jamb (very common on front-load models)
• Around the door opening, on the inner front panel
• On the back of the control panel
• On the side of the main cabinet near the bottom edge
• On the rear panel of the washer cabinet

What to write down (and why)

Record the information exactly as shown so we can match the right washer parts and diagrams.

• Model number (example: 79641379210)
• Serial number (helps with production changes)
• Brand name (Kenmore)
• Any revision or suffix characters after the model number

Quick checklist

Item	What it does	Example
Model number	Identifies the exact washer design	79641379210
Serial number	Identifies the production run	(varies)
Product type	Confirms you are in the right category	Washer

Why it matters

Kenmore model numbers can look similar, but small differences change which parts fit (door lock switch, drain pump motor, water inlet valve, and hoses). Using the exact model number helps us show the correct part list and prevents ordering the wrong replacement.

Last updated: February 2026

A bad washer drain pump on Kenmore model 79641379210 usually shows up as water left in the drum, slow or no draining, or a loud grinding/humming during drain. Before replacing parts, we check for a clog in the drain path and the pump filter per the 79641379210 owner's manual.

Common signs the drain pump is failing

• Water remains in the tub at the end of the cycle
• Washer stops mid-cycle or won’t advance past drain/spin
• Humming sound but little or no water movement (impeller not turning)
• Grinding/rattling noise during drain (debris or worn pump)
• Intermittent draining (works sometimes, fails other times)
• Error code related to draining (model-dependent)

Quick checks we do before replacing the pump

1. Unplug the washer.
2. Check the drain hose for kinks, crushing, or a clogged standpipe.
3. Clean the drain pump filter (coins, lint, socks commonly block flow).
4. Inspect the tub-to-pump hose for obstructions; on this model, a restricted hose can mimic a bad pump.
5. Run a drain/spin cycle and listen: steady hum with no drain usually points to a jammed or failed pump.

Parts that commonly fix “won’t drain” symptoms

Symptom	Most common cause	Part to consider for 79641379210
Won’t drain, loud noise	Debris-damaged pump	Washer pump 3108ER1001E
Won’t drain, pump runs weak	Failing pump motor	Drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
Drains slowly, frequent clogs	Restricted filter/housing	Washer drain pump filter 383EER2001A

Why it matters

A weak or jammed drain pump can leave clothes soaking wet, trigger drain-related stoppages, and strain the motor during spin because the washer cannot reach proper speed with water still in the tub.

Last updated: February 2026

Yes, repairing a Kenmore washer is worth it when the fix restores reliable washing and costs less than replacing the machine. For Kenmore model 79641379210, common repairs like a drain pump, door lock, or inlet valve often make financial sense compared to buying new.

Quick way to decide (repair vs. replace)

We use three checks to make the call:

• Repair cost vs. replacement cost: If the total repair (parts + labor) is under about 50% of a comparable new washer, repair is usually the better value.
• What failed: Single-part failures (pump, valve, lock) are typically good repair candidates; major tub or bearing jobs can be more expensive.
• Overall condition: If the washer is otherwise quiet, stable, and not leaking, a targeted repair is usually worthwhile.

Common “worth it” repairs on model 79641379210

These are frequent, straightforward fixes that can stop the most common symptoms:

• Not draining or stopping mid-cycle: drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
• Won’t lock or won’t start: washer door lock switch EBF49827801
• Not filling or filling slowly: washer water inlet valve 5221ER1003A
• Drain issues caused by blockage: washer drain pump filter 383EER2001A

Cost and complexity snapshot

Repair type	Typical symptom	Typical value outcome
Pump or filter service	Won’t drain, ND-style drain problems	Usually worth repairing
Door lock switch	Door won’t lock, won’t spin/start	Usually worth repairing
Inlet valve	No fill, slow fill, NF-style fill problems	Usually worth repairing
Bearings/tub work	Loud roaring, heavy vibration, leaks at tub	Often consider replacing

Why it matters

A washer replacement cost includes delivery, haul-away, and installation changes. A focused repair can restore performance quickly and extend the life of the washer without the extra replacement expenses.

What we recommend before spending money

• Confirm the symptom and any error code using the 79641379210 owner’s manual
• Check for simple causes first (clogged filter, kinked drain hose, closed water valves)
• Price the likely part and compare it to the cost of a new washer
• If the issue points to bearings or the tub, get an estimate before ordering parts

Last updated: February 2026

Yes, it’s usually worth replacing a pump on a Kenmore washer model 79641379210 when the washer is otherwise in good shape and the problem is clearly a drain or recirculation failure. Before buying parts, we check for clogs in the drain path because a blocked filter or hose can mimic a bad pump. See the 79641379210 owner’s manual for the model’s drain and maintenance guidance.

Quick decision checklist

• The washer fills and tumbles normally but won’t drain, or drains very slowly
• The tub is not leaking from the outer tub area (leaks can change the repair value)
• The pump is noisy (grinding/humming) or the impeller is jammed
• You’ve already cleared the drain pump filter and checked hoses for socks, coins, and lint
• The repair cost stays well below the cost of a comparable replacement washer

What to check before replacing the pump

1. Unplug the washer.
2. Drain any standing water safely.
3. Clean the drain pump filter and inspect the pump inlet for debris.
4. Inspect the tub-to-pump hose for obstructions and kinks.
5. If the pump runs but no water moves, the impeller is typically damaged or slipping.

Common parts involved on this model

Symptom	Most likely area	Part you may need
Won’t drain, loud pump noise	Drain pump motor	Drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
Drains slowly, frequent clogs	Filter housing/filter	Washer drain pump filter 383EER2001A
Intermittent draining, restriction	Drain hose between tub and pump	Washer tub-to-pump hose 4738ER1002A

Why it matters

A weak or jammed pump can leave water in the tub, trigger drain-related errors, and cause long cycle times. Fixing the drain system early helps prevent odor, poor spin performance, and repeat shutdowns.

Last updated: February 2026

A washing machine like the Kenmore 79641379210 is built around a wash system (tub and drum), a drive system (motor and controls), and a water-handling system (inlet valves, hoses, and drain pump). These core parts work together to fill, wash, spin, and drain safely.

Main parts you will see on most washers

• Inner drum (spin basket): holds clothes and spins to extract water
• Outer tub: holds wash water around the drum
• Drive motor and rotor: turns the drum for wash and spin
• Water inlet valve(s): controls hot and cold water entering the washer
• Drain pump and filter: pumps water out and catches debris
• Door lock switch (front-load): keeps the door locked during operation
• Control board and user interface: runs cycles, monitors sensors, shows errors

Common Kenmore 79641379210 parts that match those functions

System	What it does	Example part for this model
Draining	Pumps water out of the tub	Drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T
Filling	Lets water into the dispenser/tub	Washer water inlet valve 5221ER1003A
Safety/locking	Locks door so the washer can spin	Washer door lock switch EBF49827801

Why it matters

Knowing the “main parts” helps you troubleshoot faster. For example, a no-drain problem points to the drain pump, drain hose, or a clogged filter; a no-fill problem points to the inlet valve or supply hoses.

Quick tips before you order parts

• Match the model number 79641379210 exactly.
• Check for simple causes first (kinked hoses, clogged filter, loose wire connector).
• If you see an error code, use the code to narrow the failed system.
• Use the exploded views and part diagrams in the 79641379210 owner’s manual.

Last updated: February 2026

On Kenmore washer model 79641379210, the DE2 code points to a door/lock problem: the control is not sensing the door locking correctly, so the washer stops for safety. The most common fix is correcting a door closure issue or replacing the door lock.

What to check first (fast, no parts)

• Press the door firmly until you hear a solid latch click; remove any laundry caught in the boot area.
• Power reset: unplug the washer (or switch off the breaker) for 2 minutes, then restore power.
• Check the door strike area for cracks, looseness, or misalignment.
• Make sure the washer is level; excessive vibration can prevent a reliable lock.
• If the door feels “closed” but the washer still will not lock, the lock switch assembly is the likely failure.

Parts that commonly solve DE2 on this model

If the basic checks do not clear DE2, replacement of the door lock assembly is the most common repair.

Symptom you notice	Most likely cause	Typical next step
Door will not lock, no click	Failed lock mechanism	Replace door lock assembly
Locks sometimes, then errors mid-cycle	Intermittent lock switch or wiring	Inspect harness, replace lock if needed
Drains but will not start/spin	Control not seeing “locked” signal	Confirm lock operation, then replace lock

Recommended model-matched part:

• Washer door lock switch EBF49827801

Why it matters

The washer uses the door lock signal to prevent tumbling and high-speed spin with an unlatched door. When the control cannot confirm a locked door, it stops the cycle to protect you and the machine.

Where to find model-specific steps

For the exact reset procedure, error-code behavior, and access steps for the lock on model 79641379210, use the 79641379210 manual.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use and basic maintenance. For Kenmore model 79641379210, you can usually reach the upper end of that range by keeping the drain system clear, using the right detergent amount, and avoiding chronic overloading; see the 79641379210 owner's manual for care guidance.

What affects washer lifespan the most

• Load size and balance: frequent overloading or unbalanced loads increase wear on bearings, suspension, and the drive system.
• Drain health: coins, lint, and small items strain the pump and can cause slow drains.
• Water quality: hard water speeds up scale buildup in valves and internal passages.
• Detergent habits: too much HE detergent can cause oversudsing and residue.
• Door boot care (front-load): moisture left behind leads to odor and premature rubber wear.

Maintenance that helps you get 10 to 15 years

• Clean the pump filter and check for debris if draining slows.
• Run a monthly tub-clean cycle (or hot cycle) with an approved cleaner.
• Leave the door slightly open between loads to dry the tub.
• Level the washer and re-check if it starts vibrating more than normal.
• Use HE detergent and measure carefully.

Common “end-of-life” symptoms and what they usually point to

Symptom	Most common cause	Typical fix path
Won’t drain or drains slowly	Clogged filter, failing pump	Clean filter; test/replace pump
Loud rumble in spin	Tub bearing wear	Bearing/tub service
Won’t fill or fills slowly	Inlet valve restriction/failure	Check screens; replace valve
Door won’t lock	Door lock failure	Replace door lock

If your 79641379210 is not draining, a frequent repair is replacing the drain pump motor (4681EA2001T) - washer part by lg electronics 4681EA2001T.

Why it matters

Knowing the typical lifespan helps you decide whether routine repairs (pump, inlet valve, door lock) make sense versus planning for replacement when major components like bearings or the tub assembly start failing.

Last updated: February 2026