Kenmore Elite 11047089600 washer Parts

Yes. Your Kenmore Elite washer model 11047089600 uses a drain pump clean-out (often called a pump filter or coin trap) that catches lint and small items before they reach the drain pump; cleaning it helps prevent no-drain problems and odors. See the 11047089600 owner's manual for the exact access method for your version.

Where the “filter” is on this washer

On most Kenmore front-load designs like model 11047089600, the filter is part of the drain system and is accessed from the lower front area.

Common places to check:

• Behind a small lower access panel (kick plate)
• At the drain pump clean-out cap (coin trap)
• In the tub-to-pump hose path if an item bypassed the trap

How to clean the drain pump filter (safe, quick steps)

Before you start, unplug the washer to avoid electric shock.

• Put towels down and use a shallow pan; water will come out
• Open the lower access panel
• If your washer has a small drain hose, drain water into a container first
• Slowly turn the pump clean-out cap counterclockwise to release water
• Remove lint, coins, hair pins, and debris; rinse the cap and cavity
• Reinstall the cap firmly (hand-tight) and run a quick rinse and drain

If it still will not drain after cleaning

A clog or a failing pump can mimic a “dirty filter” symptom.

Symptom	Most likely cause	What we check next
Hums but no drain	Blockage at pump or hose	Inspect washer tub-to-pump hose WPW10467168 and clamps
Drains slowly	Partial clog, restricted hose	Recheck coin trap and standpipe height
No sound, no drain	Pump failure or control issue	Test/replace pump 280187 and verify wiring

Why it matters

A clean pump filter protects the drain pump, reduces standing water that can cause odors, and helps prevent common drain errors and long cycle times.

Last updated: February 2026

For the Kenmore Elite washer model 11047089600, the most reliable “hard reset” is a power cycle: unplug the washer (or switch off the breaker) for 1 to 5 minutes, then restore power and start a new cycle. For control resets during use, this model uses the STOP and POWER buttons as shown in the 11047089600 owner's manual.

Reset options that work on model 11047089600

Use the least disruptive option first.

• Power cycle reset: Unplug 1 to 5 minutes, then plug back in.
• Cancel the current cycle: Press STOP twice; the washer powers down and the door unlocks (it may drain first if water is hot/high).
• Restart with a new cycle: Press STOP twice, press POWER, choose a cycle, then press and hold START for about 1 second.
• Change options after starting: Press STOP once, change options/modifiers, then press and hold START for about 1 second.
• Manual drain (if needed): Press STOP twice, press POWER, select RINSE/DRAIN & SPIN, remove extra rinse options, then press and hold START about 1 second.

Quick “which reset should I use?” table

Situation	Best reset action	What to expect
Washer is frozen or unresponsive	Power cycle reset	Clears the control and restores normal button response
Wrong cycle selected	STOP twice, then POWER and reselect	Starts over at the beginning of the new cycle
Need to change options mid-cycle	STOP once, adjust, then START (hold 1 second)	Cycle continues with updated settings
Water won’t drain / too much water in tub	Manual drain steps	Drains and unlocks after spin completes

Why it matters

A true “hard reset” on electronic Kenmore washers is mainly about clearing the control logic and safely ending a cycle. Using STOP, POWER, and holding START for about 1 second prevents door-lock issues and helps the washer drain before unlocking when conditions require it.

Last updated: February 2026

To force your Kenmore Elite washer model 11047089600 to drain, we recommend using the control-panel Rinse/Drain & Spin cycle after canceling the current cycle. This safely runs the drain pump and unlocks the door when draining and spinning are complete.

Fastest way to drain using the controls

Follow the manual steps in the 11047089600 owner's manual:

• Press STOP twice to cancel the wash cycle.
• Press POWER.
• Select RINSE/DRAIN & SPIN.
• Press 2ND RINSE to remove any rinse options.
• Press and hold START (about 1 second) to begin draining.
• When the spin finishes, the door unlocks and you can remove items.

If the washer still will not drain

A no-drain problem is usually caused by a restriction in the drain path or a failing drain pump.

• Check the drain hose for kinks, crushing, or a clog.
• Make sure the drain hose is not shoved too far into the standpipe (it needs an air gap).
• Confirm the standpipe or laundry tub drain is flowing freely.
• If you hear the pump humming but water does not move, inspect the pump area for debris.
• If the washer drains slowly or intermittently, the drain pump can be the issue.

Common drain-related parts for this model

Symptom	What it often points to	Model-matched part to consider
Hums but no drain	Jammed or failing pump	Pump 280187
Leaks during drain	Loose or damaged drain hose connection	Washer tub-to-pump hose WPW10467168
Hose slips or seeps	Weak clamp tension	Clamp WP285655

Why it matters

Forcing a drain the right way protects the door lock system, reduces the chance of a spill, and helps confirm whether the issue is a control setting versus a drain-path or pump problem.

Last updated: February 2026

Yes. Kenmore Elite appliances are positioned as Kenmore’s higher-end line, and the Kenmore Elite washer model 11047089600 is built for premium performance features, long-term durability, and a more refined fit and finish than basic Kenmore models. For model-specific operation and care details, use the 11047089600 owner's manual.

What “high end” means for this Kenmore Elite washer

High end typically shows up in a few practical ways that affect daily use and ownership:

• Durability-focused design: this model’s warranty coverage includes long-term protection on key tub components (stainless steel drum and plastic tub) when used and maintained as instructed.
• High-efficiency (HE) washing: it’s designed to use high-efficiency detergent only, which supports strong cleaning with lower water use.
• Installation flexibility: it can be installed in multiple locations (laundry room, closet, recessed area, under a counter) when requirements are met.
• Upgrade options: pedestal and stacking options are supported for a more “built-in” laundry setup.

Quick comparison: Kenmore vs Kenmore Elite (typical)

Feature area	Standard Kenmore (typical)	Kenmore Elite (typical)
Build and components	Basic to mid-grade	More premium components and durability focus
Efficiency	Varies	Commonly HE-focused
Features	Core cycles	More convenience and performance features
Ownership experience	Good	Better long-term value when maintained well

How to get the most “Elite” performance

These steps keep cleaning performance high and help prevent common washer issues:

• Use HE detergent and measure carefully to avoid oversudsing.
• Keep the door boot clean and dry; replace it if it’s torn or leaking (see washer door boot WP8182119).
• If draining is slow or you see standing water, check the drain path and consider the drain pump (see pump 280187).
• Follow the cleaning and hose inspection intervals in the manual.
• Level the washer and confirm the drain and electrical requirements are met.

Why it matters

“High end” is most noticeable over time: better materials, better efficiency, and better results when the washer is installed correctly and maintained. That translates into fewer performance problems and more consistent wash quality.

Last updated: February 2026

Yes, repairing a Kenmore Elite washer like model 11047089600 is worth it when the fix restores safe, reliable operation for less than replacing the washer, especially for common wear items (drain pump, door boot, belt) and when the tub and drum are still in good shape. See the 11047089600 owner's manual for care and troubleshooting guidance.

Quick decision checklist

• Repair it if the washer still fills, drains, and spins, and the issue is a single failed part (leak, no drain, door won’t lock).
• Repair it if the problem is maintenance-related (clogs, hose issues, cleaning) and not repeated breakdowns.
• Repair it if the stainless steel drum and plastic tub are intact (no severe corrosion, cracks, or major bearing noise).
• Replace it if you have repeated major failures (control boards, wiring damage) or persistent leaks from the tub area.
• Replace it if the washer is excessively loud with grinding or rumbling that points to major internal wear.

Common repairs that are usually cost-effective

These are frequent front-load washer fixes that often bring the machine back to normal performance:

• Not draining or draining slowly: pump 280187
• Door seal leaks, mildew, or tears: washer door boot WP8182119
• Door won’t lock or cycle won’t start: washer door lock WP8183270
• Slipping, no tumble, or poor spin: belt WPW10388414
• Excessive shaking or “walking”: washer suspension spring set W10135004

Cost and complexity comparison

Situation	Typical cause	Typical difficulty	Usual best choice
Won’t drain	Pump or hose restriction	Medium	Repair
Leaks at door	Door boot	Medium	Repair
Won’t start, door error	Door lock	Medium	Repair
Loud grinding/rumble	Bearings or major tub wear	High	Replace (often)

Why it matters

A targeted repair can extend the life of your 11047089600 and prevent secondary damage (for example, a weak drain pump can leave water in the tub, leading to odors and repeat drain errors). Following the cleaning and care steps in the 11047089600 owner's manual also reduces future repairs.

Last updated: February 2026

On the Kenmore Elite washer model 11047089600, the OE error code means the washer is not draining properly (a drain error). In most cases, the washer cannot pump the water out fast enough because of a restriction in the drain path or a drain pump issue; see the 11047089600 owner's manual for the exact reset and drain-check steps.

What to check first (fast fixes)

• Cancel the cycle and run Drain/Spin (or a drain-only option if your control has it).
• Check the drain hose for kinks, crushing, or a clogged standpipe.
• Make sure the drain hose is not pushed too far down the drain pipe (it can siphon or restrict flow).
• Reduce oversudsing: use HE detergent only and use less if you see lots of foam.
• If the tub is full of water, unplug the washer before accessing any lower panels.

Likely causes and the parts that commonly solve OE

OE is almost always caused by a blockage or a weak pump. For this model, these parts are common suspects:

• Pump 280187 (failed motor, jammed impeller, or internal restriction)
• Washer tub-to-pump hose WPW10467168 (coin, sock, lint clog)
• Drain hose or household drain (standpipe) restriction
• Excess suds slowing drainage (detergent issue)

Quick diagnosis guide

Symptom	Most likely cause	What we do next
Hums but drains slowly	Partial clog or weak pump	Inspect hoses, then consider replacing the pump
No pump sound at all	Pump not running or control/lock issue	Check door lock, wiring, then pump
Drains sometimes, OE other times	Intermittent clog or oversudsing	Clear hoses, correct detergent amount
Water backs up into tub	Household drain problem	Clear standpipe or plumbing

Why it matters

A drain error can leave water in the tub, prevent high-speed spin, and cause repeated cycle failures. Fixing the drain path quickly helps protect the motor control system and prevents odors from standing water.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For the Kenmore Elite 11047089600, keeping up with routine care (hoses, cleaning, and proper loading) helps you reach the high end of that range; see the maintenance schedule in the 11047089600 owner's manual.

What affects washer lifespan the most

• Overloading or consistently unbalanced loads (extra strain on the drive system and suspension)
• Poor drainage (standing water stresses the drain system and can lead to repeat failures)
• Hard water and detergent buildup (can cause odors, residue, and component wear)
• Worn inlet hoses or restricted water flow (slower fills, more cycle stress)
• Skipping routine cleaning (door seal area, dispenser area, and tub care)

Typical lifespan by usage pattern

Usage pattern	Typical lifespan	What to watch for
Light (1 to 3 loads/week)	12 to 15 years	Hoses aging, minor leaks
Average (4 to 7 loads/week)	10 to 13 years	Drain issues, vibration
Heavy (8+ loads/week)	7 to 10 years	Bearings, pump, suspension

Maintenance that extends life on model 11047089600

We recommend focusing on the same care items called out in the manual (washer care and water inlet hoses):

• Inspect water inlet hoses regularly and replace if bulging, cracking, or leaking
• Keep the door area dry between loads to reduce odor and residue
• Use the correct amount of HE detergent; too much increases buildup
• Run periodic cleaning cycles (especially if you wash in cold water often)
• Address draining problems early; a failing drain pump can turn into repeat no-drain issues

If your washer is not draining or is leaving water behind, the drain pump is a common wear item on front-load designs; the model-specific replacement part is the pump 280187.

Why it matters

A washer near the end of its expected lifespan often shows early warning signs (long fill times, intermittent no-drain, louder spin, or increased vibration). Catching those symptoms early helps prevent secondary damage and keeps repair costs predictable.

Last updated: February 2026

Your Kenmore Elite washer’s model number is printed on a rating label on the washer cabinet; on model 11047089600, you’ll typically find it around the door opening (door jamb) or on the cabinet near the control panel. Use the exact model number to match the correct parts and manual.

Where to look for the model number label

Check these common spots on Kenmore front-load washers:

• Behind the washer door, around the door opening (door jamb)
• Along the inside edge of the door frame
• On the back of the control panel area
• On the side of the main cabinet near the bottom front
• Occasionally behind the lower access panel (if your unit has one)

What the model number looks like (and why it matters)

Kenmore Elite front-load model numbers are usually a long number string. For this washer family, the manual lists models like 110.4708 and 110.4709 with a final color digit (shown as a symbol in the manual). The key is to copy the full number exactly as printed on your label.

Quick examples

What you see on the label	What it means	What to do
110.4708… or 110.4709…	Model series/family	Record the full number
Extra last digit/letters	Color or revision	Include it when ordering parts
Missing/illegible label	Normal wear/cleaning damage	Use the manual’s model list to narrow it down

Tips to avoid ordering the wrong parts

Using the correct model number prevents mismatches on common repair items like the drain pump, door boot, and door lock.

• Write the model number and serial number exactly as shown
• Take a clear photo of the label before it fades further
• Match parts by model first, then confirm by part name and ID
• If you’re troubleshooting an error, use the model number to find the right code list

Helpful references

• Use the 11047089600 owner’s manual to confirm model labeling and supported model series.
• If your washer is showing a balance-related code, see Kenmore front load washer dc error code.

Why it matters

Kenmore Elite washers often share similar styling across multiple model series; the model number is what ensures the correct fit for parts, wiring, and troubleshooting steps.

Last updated: February 2026

Kenmore Elite is a premium Kenmore product line that has been produced across multiple years and generations, not a single “made in” year. For the Kenmore Elite washer model 11047089600, the most reliable way to pin down the exact production era is to use the model’s identification information and documentation in the 11047089600 owner's manual.

How to identify the production era for model 11047089600

We use the model and serial tag (typically on the door opening or cabinet area on front-load washers) to determine the manufacturing date range.

• Find the model and serial number label on the washer
• Write down the serial number exactly as shown
• Compare the serial format to the identification guidance in the 11047089600 owner's manual
• If you are ordering parts, match by model number 11047089600 first, then confirm by symptom and part diagram
• Keep the purchase date handy; it helps narrow the timeframe when multiple revisions exist

What “Kenmore Elite” means (and why there is no single year)

Kenmore Elite is a higher-end tier within the Kenmore brand. Sears used the “Elite” label on multiple appliance categories (including washers) over many years, so the correct answer depends on the specific model number, not the Elite name alone.

Quick reference

Term	What it tells you	What it does not tell you
Kenmore Elite	Premium product tier	Exact manufacturing year
11047089600	Specific washer design family	Exact build date without serial
Serial number	Factory date code information	Parts compatibility by itself

Why it matters

Knowing the approximate production era helps us avoid ordering the wrong revision of a part (for example, a door lock, drain pump, or control board) and speeds up troubleshooting when symptoms point to common wear items.

If your question is really about when your washer was built, the serial number is the key. If your question is about a repair, we typically start with the symptom and the most likely parts, such as the washer door lock WP8183270 or pump 280187.

Last updated: February 2026