Installation guide
Owner’s manual
Error Codes
How big is the Kenmore Coldspot refrigerator?
The Kenmore Coldspot side-by-side refrigerator model 10654584400 is a full-size unit; most Kenmore 106 side-by-side refrigerators measure about 66 to 70 inches tall, 32 to 36 inches deep (varies with handles), and 32 to 36 inches wide. For the exact cabinet and door-swing dimensions for your unit, use the 10654584400 owner's manual.
Measure in inches with a tape measure; include the items that affect fit.
- Height: floor to top of hinge cover (or top of cabinet if hinges are removed for delivery)
- Width: widest point across the cabinet (not the doors) unless you need door clearance
- Depth (cabinet only): back panel to front of doors (no handle)
- Depth (with handle): back panel to the front of the handle
- Door swing clearance: space needed for doors to open fully and bins to clear a wall
The manual calls out ventilation and wall clearance so the refrigerator cools properly and doors open without binding.
- Leave 1/2 inch (1.25 cm) space on each side and at the top for ventilation
- If installed next to a fixed wall, leave 2 inches (5.08 cm) minimum on each side (depending on your model) for door swing
- If equipped with an ice maker, allow extra space at the back for the water line connection
| What you are planning | Dimension to use | What to include |
|---|---|---|
| Fit in the opening | Width, height | Cabinet plus hinge height |
| Walkway clearance | Depth | Include handles if they stick out |
| Full access to bins/shelves | Door swing | Clearance next to walls/cabinets |
Correct measurements prevent delivery surprises, protect door gaskets from rubbing, and ensure proper airflow around the condenser and compressor so temperatures stay stable.
Last updated: January 2026
Why is my Kenmore side by side freezer not freezing?
If your Kenmore 10654584400 side-by-side freezer isn’t freezing, the most common causes are incorrect control settings, blocked airflow (vents packed with food or frost), or a cooling-system problem such as a failed compressor start component or a weak compressor. Start with settings and airflow checks first.
- Confirm the freezer set point is 0°F (-18°C) and the refrigerator is 37°F (3°C); changing to colder won’t cool faster. See the 10654584400 owner's manual.
- Wait a full 24 hours after any control change or power interruption for temperatures to stabilize.
- Make sure air vents are not blocked by packages; leave space around food for circulation.
- Check that the freezer door closes tightly and isn’t being held open by bins or packages.
- Look for heavy frost on the back freezer panel (often points to a defrost/airflow issue).
| What you notice | Most likely area to check | Common next step |
|---|---|---|
| Freezer warm, fridge also warm | Sealed system or compressor start issue | Listen for compressor cycling/clicking; service may be needed |
| Freezer warm, fridge OK | Airflow/evaporator fan or frost blockage | Check vents, look for frost buildup |
| Frost blanket on freezer back wall | Defrost system problem | Inspect defrost components and airflow |
| Ice maker stopped and water dispenser weak too | Water supply issue (separate from cooling) | Check house water, then valve/filter |
These parts are often involved when airflow or defrost problems prevent proper freezing:
- Refrigerator defrost bi-metal WPW10225581 (can stop defrost heating when it fails)
- Refrigerator heater WP2323198 (defrost heater that melts frost off the evaporator)
- Refrigerator condenser fan W10181323 (helps remove heat at the condenser)
A freezer that is not freezing is usually an airflow or heat-removal problem. Blocked vents or heavy frost can keep cold air from circulating, and a failing compressor or condenser fan can prevent the system from pulling temperatures down to the factory-recommended 0°F.
Last updated: January 2026
Why is my Kenmore side by side ice maker not making ice?
On Kenmore refrigerator model 10654584400, an ice maker usually stops making ice because the freezer is not cold enough yet, the ice maker is switched OFF, the ice storage bin or sensor door is not positioned correctly, or water is not reaching the ice maker (shutoff valve, filter, or inlet valve issue). See the 10654584400 owner's manual for the exact control and ice maker checks.
- Wait for normal startup: allow 72 hours for full ice production after installation; allow 24 hours after water hookup or temperature changes.
- Confirm the ice maker is ON: lower the wire shutoff arm (arm down) or move the ice maker switch to ON (left), depending on your version.
- Verify freezer temperature: if the freezer is too warm, ice production will be slow or stop.
- Make sure the ice storage bin is seated correctly; on door-bin models, the bin should sit level and snap in securely.
- Check the water supply shutoff valve to the refrigerator is fully open.
- If a water filter is installed, reseat it and replace it if clogged (a restricted filter can stop ice production).
| What you see | Most likely cause | What to do |
|---|---|---|
| No ice at all after it previously worked | Ice maker turned OFF or bin/sensor not engaged | Reinstall bin; ensure sensor door can close; turn ice maker ON |
| Ice maker mold is dry (no water) | Water supply off, clogged filter, or bad inlet valve | Open shutoff valve; replace filter; test/replace valve |
| Ice jam at ejector | Cube stuck in ejector area | Clear jam with a plastic utensil (no sharp tools) |
| Low production | Freezer too warm or heavy recent use | Set temps correctly; allow 24 hours to recover |
If water is not filling the ice maker, these model-compatible parts are common fixes:
- Refrigerator inlet valve W10408179 (controls water flow into the refrigerator)
- Genuine Kenmore refrigerator water filter EDR3RXD1 (a clogged filter can restrict flow)
Ice makers depend on two basics: a cold freezer and steady water flow. A slightly warm freezer, a mis-seated door bin/sensor, or a restricted filter can stop ice production even when the refrigerator otherwise seems to run normally.
Last updated: January 2026
