KitchenAid KUDS35FXSS2 undercounter dishwasher Parts

To clear an error code on your KitchenAid KUDS35FXSS2 dishwasher, reset power to the control by turning the dishwasher off at the breaker (or unplugging it) for about 1 minute, then restore power and try a short cycle. This clears many temporary control faults.

Quick reset steps (safe first)

• Turn the dishwasher off at the circuit breaker (preferred) or unplug it.
• Wait 60 seconds.
• Restore power.
• Start the shortest wash cycle.
• After about 2 minutes, unlatch the door, wait 5 seconds, then open the door and confirm there is water in the bottom of the tub.

For model-specific button sequences and what each code means, use the troubleshooting and operation details in the owner's manual.

If the code comes back right away

A repeating error code usually points to an ongoing issue (drain, fill, heating, or a sensor reading). Check these common causes:

• Not draining: kinked hose, clogged drain path, or a failing drain pump
• Not filling: water supply turned off, inlet screen clogged, or a weak inlet valve
• Heating issue: heater circuit problem or poor water circulation
• Door not latching: door not fully closed or latch alignment issue

Parts that commonly relate to repeat codes on this model

Symptom you notice	What to check first	Related part on this model
Water left in tub	Drain path and pump	Dishwasher drain pump WPW10348269
No water entering	Supply valve and inlet valve	Dishwasher water inlet valve WPW10327249
Poor drying, heater-related code	Heater and circulation	Dishwasher heater W10703867

Why it matters

Clearing the code gets you back to washing quickly when the control just needs a reset. If the code returns, the dishwasher is protecting itself by flagging a condition that can lead to poor cleaning, leaks, or repeat shutdowns.

Last updated: February 2026

The most common issues we see on KitchenAid dishwashers like model KUDS35FXSS2 are poor cleaning or draining, door leaks, and “won’t start” symptoms. Many of these trace back to basic checks (power, water supply, door latch timing) and routine maintenance.

Most common symptoms and what usually causes them

• Not starting or appears dead: tripped breaker, blown fuse, door not fully latched
• Start/Resume light flashing: door not closed within about 3 seconds after pressing Start/Resume
• Not filling with water: water supply turned off, kinked supply line, inlet valve issue
• Not draining: drain hose restriction, drain pump problem, disposal/air gap blockage
• Leaking at the door: worn door seal, misalignment, or excess suds from wrong detergent

Quick checks we recommend first (fast, no parts)

1. Confirm the breaker is on and the dishwasher has power.
2. Make sure the door is closed tightly and latched.
3. Set a cycle correctly, then press Start/Resume and close the door promptly (within 3 seconds).
4. Verify the water supply valve is fully open.
5. Run the shortest cycle; after about 2 minutes, open the door and confirm there is water in the bottom of the tub.

These steps match the “If dishwasher does not operate” and “Check operation” guidance in the installation instructions. See the installation guide.

Parts that commonly solve these problems on KUDS35FXSS2

If the basic checks do not fix it, these model-matched parts are common next steps:

Symptom	Common part to check/replace	Why it helps
Won’t drain / water left in tub	Dishwasher drain pump WPW10348269	Restores pumping water out during drain
Not filling / low water	Dishwasher water inlet valve WPW10327249	Controls water entering the dishwasher
Leaks at door	Dishwasher door seal W11177741	Seals the tub to the door to prevent drips

Why it matters

Dishwashers are designed to run longer cycles for energy savings; a normal load can average 2 to 3 hours. When cleaning or drying seems “worse,” it is often a setup or maintenance issue, not a major failure. The installation instructions also note rinse aid is important for drying and reducing hard-water deposits. See the installation guide.

Last updated: February 2026

Your KitchenAid undercounter dishwasher’s model number is on the appliance ID label, typically located on the tub frame around the door opening. Open the door and look along the left or right side of the inner frame; the label lists the model and serial number.

Where to look on a KUDS35FXSS2 dishwasher

Check these common ID-label locations first:

• Left side of the tub frame (vertical edge) when the door is open
• Right side of the tub frame (vertical edge) when the door is open
• Top edge of the tub opening (under the countertop lip, visible with the door open)
• On the inner door edge (near the latch area)

What the label looks like and what to copy

The label usually includes several lines of information. For parts and diagrams, we use the model number exactly as printed.

Label item	What it’s used for	Example format
Model number	Correct parts lookup and diagrams	KUDS35FXSS2
Serial number	Production run details	Letters and numbers
Type/engineering code	Service identification	Varies

Tips if the label is hard to read

If the sticker is worn or covered, these steps help:

• Wipe gently with a damp cloth and a drop of dish soap; dry and recheck
• Use a flashlight and view from an angle to make faint print stand out
• Take a close-up photo and zoom in
• Write down every character; model numbers are case-sensitive and must match exactly

Why it matters

KitchenAid dishwashers can look similar across series, but parts like the door seal, drain pump, and electronic control board vary by model. Using the exact model number prevents ordering the wrong replacement part.

For a diagram-based reference to your model identification and service information, use the KUDS35FXSS2 owner's manual.

Last updated: March 2026