Kenmore Elite 66514793N512 dishwasher Parts

To take your Kenmore Elite dishwasher model 66514793N512 out of lock mode, press and hold SANI RINSE for 3 seconds until the Locked light turns off. If the controls do not respond, wake the panel first, then try the 3-second hold again (see the 66514793N512 owner's manual).

• Press START/RESUME or CANCEL/DRAIN once to wake the control (Sleep mode can prevent unlocking).
• Press and hold SANI RINSE for 3 seconds.
• Confirm the Locked indicator light turns off.
• If you press a button while locked, the Locked light typically flashes.
• Close the door and start a cycle normally.

These checks solve most “stuck in lock mode” complaints on Kenmore 665-series dishwashers.

• Make sure the door is fully closed and latched.
• Press CANCEL/DRAIN, wait a moment, then try the SANI RINSE 3-second hold again.
• Power-cycle the dishwasher (turn off the breaker for 1 minute, then restore power) and retry.
• If the door will not latch consistently, inspect the latch for damage or looseness; a failing latch can make the control act unpredictably (see dishwasher door latch WPW10653840).

Control Lock prevents accidental button presses between cycles, especially when cleaning the console or when kids bump the controls. Unlocking restores normal cycle selection, Delay Hours, and Start/Resume operation.

Last updated: January 2026

For Kenmore Elite dishwasher model 66514793N512, a “hard reset” is typically done by resetting the control: press START/RESUME, then press and hold CANCEL/DRAIN twice to clear the current cycle so you can restart fresh (see the 66514793N512 owner's manual).

1. Open the door slightly to stop the cycle; wait for spraying to stop.
2. Press START/RESUME.
3. Press and hold CANCEL/DRAIN twice to reset the control.
4. Select your new cycle and options.
5. Press START/RESUME and close the door within 3 seconds.

Try these quick checks before assuming a control failure:

• Make sure the door is fully latched; the cycle will not start if the door is not closed within 3 seconds after pressing START/RESUME.
• Run a cancel and drain; if water is in the tub, let it drain completely.
• Check the house breaker or GFCI outlet; restore power if it tripped.
• If the unit is installed recently, confirm power is connected correctly using the 66514793N512 installation guide.

Resetting the control the right way prevents partial cycles, standing water, and “won’t start” symptoms caused by an interrupted cycle or an unlatched door. It also helps you avoid replacing parts like the electronic control when the issue is simply a cycle that needs to be cleared.

Last updated: January 2026

On a Kenmore Elite dishwasher like model 66514793N512, error code F2E2 points to a communication problem between the user interface (console) and the main electronic control. This often shows up as unresponsive buttons, beeping, or a cycle that will not start.

• Press Cancel/Drain and wait for the drain to finish.
• Turn power off at the breaker for 1 minute, then restore power.
• Make sure the door closes and latches firmly; a poor latch can mimic control issues.
• If the keypad is acting “stuck,” wipe the console area dry and try again.
• Run a quick test cycle per the 66514793N512 owner’s manual to confirm the code returns.

F2E2 is most commonly triggered by one of these conditions:

• Moisture or contamination at the console/keypad connection
• Loose or damaged wiring between the console and control board
• Failed user interface (console) electronics
• Failed main electronic control

When the user interface and main control cannot “talk” reliably, the dishwasher may stop mid-cycle or refuse to start to prevent improper heating, draining, or wash motor operation. Fixing the communication fault restores normal cycle selection and operation.

For model-family code definitions and troubleshooting flow, use our Kenmore 665 model dishwasher error codes reference.

Last updated: January 2026