Kenmore 79096021405 electric range Parts

To reset your Kenmore electric range model 79096021405, turn the range OFF, then disconnect power at the breaker (or unplug it) for 1 to 2 minutes and restore power. After power returns, reset the clock and any oven settings using the steps in the 79096021405 owner's manual.

Safe reset steps (recommended)

• Turn all surface knobs to OFF and cancel any oven function.
• Switch the range circuit breaker OFF (or unplug the cord if accessible).
• Wait 1 to 2 minutes to let the control fully power down.
• Restore power at the breaker (or plug back in).
• Set the clock and reselect your desired bake or broil settings.
• If the range was in self-clean and the door is locked, wait for the oven to cool; do not force the door.

If the reset is after a power outage

The manual warns not to operate the range during a power failure. If power drops while cooking:

• Turn the range OFF immediately.
• When power resumes, reset the clock and oven function.

When a reset does not fix the problem

A reset restores normal operation only when the issue is a temporary control glitch. If the control stays dead, beeps, or heats incorrectly, these are common next checks:

• Confirm the breaker is fully reset (OFF then ON).
• Check for a loose or burned power connection at the range terminal block (power off first).
• Look for a failed heating circuit if the oven will not heat (bake or broil element).
• If the oven will not bake, inspect the frigidaire range bake element 316075103 for visible damage.

Quick symptom guide

Symptom after reset	Most likely direction	What we do next
Display blank	Power supply issue	Check breaker, cord, terminal block
Oven heats wrong or not at all	Heating component issue	Check bake/broil elements
Error code shows	Control sensing issue	Use an error code guide and follow tests

Why it matters

Resetting correctly protects the electronic control and helps prevent the range from restarting unexpectedly after a power interruption; it also ensures the clock and oven functions are restored to safe, predictable operation.

Last updated: February 2026

On Kenmore electric range model 79096021405, an oven element usually stops heating because the bake element or broil element has failed, a wire connection has burned/loosened, or the electronic control is not sending power. Start with a visual inspection, then test the element for continuity and check for error codes in the 79096021405 owner's manual.

Quick checks we recommend first

• Turn off power at the breaker before touching wiring or elements.
• Look for blisters, cracks, or a separated spot on the element.
• Confirm you are using BAKE (lower element) vs BROIL (upper element).
• Make sure the oven vent area is not blocked; heat and airflow issues can affect performance.
• If the control is beeping and showing an F code, clear it with STOP/CLEAR and re-test.

Most common causes (and what to do)

What you notice	Likely cause	What we do next
No heat on BAKE, broil works	Failed bake element	Test and replace the frigidaire range bake element 316075103
No heat on BROIL, bake works	Failed broil element	Inspect and test the broil element (replace if open)
Oven heats sometimes, then stops	Loose/burned wire at element or terminal	Inspect connectors for heat damage; repair wiring as needed
Control beeps, shows F code	Control detected a fault	Use the Kenmore 790 self-cleaning range error codes guide, then troubleshoot the listed circuit

How to test an oven element (basic method)

1. Shut off power at the breaker.
2. Remove mounting screws and gently pull the element forward.
3. Check the element terminals and wires for discoloration or melted insulation.
4. Use a multimeter to check continuity across the element terminals.
5. If the element tests open (no continuity), replace it.

Why it matters

A failed bake or broil element can leave you with undercooked food, long preheat times, or no heat at all. Catching a burned connector early also helps prevent repeat failures after you install a new element.

Last updated: February 2026

Yes. We can replace the oven heating (bake) element in a Kenmore electric range like model 79096021405 by shutting off power, removing the failed element, and installing a matching replacement with the wires reconnected securely.

Before you start (safety and access)

• Turn off power at the breaker (240V) or unplug the range if accessible.
• Confirm the oven cavity and element are completely cool; elements can stay hot after being turned off.
• Do not immerse heating elements in water; they are designed to “self-clean” during normal operation.
• Keep the oven vent unobstructed during use; blocking it can affect baking results and overheat nearby surfaces.

Basic replacement steps (typical for this model style)

1. Remove oven racks for working room.
2. Locate the bake element at the bottom of the oven (some versions are visible; some are hidden under the oven bottom panel).
3. Remove the mounting screws holding the element to the rear wall or floor.
4. Carefully pull the element forward a few inches and hold the wires so they do not slip back through the insulation.
5. Transfer wires to the new element terminals (one at a time), then reinstall screws and reassemble panels.
6. Restore power and test Bake.

Which part is usually involved?

For Kenmore model 79096021405, the bake element commonly replaced is the frigidaire range bake element 316075103.

Symptom	Most likely cause	What we check next
Oven will not heat in Bake	Burned/open bake element	Look for blisters, cracks, or no glow
Oven heats unevenly	Weak bake element or airflow issue	Verify racks, do not block vent
Breaker trips when Bake starts	Shorted element or wiring	Inspect terminals and insulation

Why it matters

A failing bake element can cause long preheat times, underbaking, and temperature swings. Replacing the element restores normal heat output and helps protect the control and wiring from repeated high-current cycling.

For model-specific diagrams, fastener locations, and access panels, use the 79096021405 owner's manual and the 79096021405 installation guide.

Last updated: February 2026

For the Kenmore 79096021405 electric range, the oven’s wattage depends on which heating function is running. Most electric ovens of this type draw roughly 3,000 to 5,000 watts when actively heating; check the exact ratings and electrical requirements in the 79096021405 owner’s manual.

Typical wattage you can expect

Electric ranges use different loads for different functions, and they cycle on and off to hold temperature.

• Bake element: commonly ~2,500 to 3,500 watts
• Broil element: commonly ~3,000 to 4,500 watts
• Convection fan (if equipped): typically under ~200 watts (motor load)
• Oven light: 40-watt appliance bulb (per the manual)
• Cooktop elements: vary by element size and setting

Quick reference: what “watts” means for your range

What you’re measuring	What it tells you	Why it changes
Element watt rating	Maximum heat output for that element	Fixed by design
Actual power draw while cooking	What the range uses at that moment	Cycles on/off with thermostat
Total range demand	What the circuit must support	Oven + cooktop loads can overlap

How to find the exact watt ratings for 79096021405

Use these reliable places (in order):

1. The electrical ratings section in the 79096021405 owner’s manual
2. The model and serial plate location described in the manual (range frame area near the storage or warmer drawer)
3. The wiring and connection requirements in the 79096021405 installation guide

Why it matters

Knowing wattage helps us match the correct circuit capacity, diagnose weak heating (for example, a failing element), and choose the right replacement parts. If your oven will not heat or heats unevenly, the frigidaire range bake element 316075103 is a common wear item to check.

Last updated: February 2026

For Kenmore ranges like model 79096021405, the model number and serial number are printed on an identification plate. On this model, that plate is located on the right side of the oven front frame, inside the storage or warmer drawer compartment.

Where to look on Kenmore model 79096021405

We recommend checking these spots in order:

• Pull out the storage or warmer drawer and look on the right side of the oven front frame
• Look for a metal or foil identification plate (not a paper tag)
• Find the line labeled Model No. (it may show 790. followed by more digits)
• Record the Serial No. as well; it helps match parts and wiring
• Compare what you find to the format shown in the 79096021405 owner’s manual

What the model number looks like (and why “790” matters)

Kenmore model numbers often start with a 3-digit prefix that identifies the manufacturer family. For many Kenmore electric ranges, 790 is a common prefix, and the full model number is what we use to match the correct bake element, control panel, and other range parts.

What you see on the plate	What it means	What to do with it
Model No. 790.XXXXX	Model prefix + full model ID	Use the full number to look up parts
Serial No. XXXXXXXXX	Production identifier	Keep it for service and troubleshooting

Why it matters

Using the exact model number prevents ordering the wrong part. Small differences in a Kenmore electric range can change the correct surface element control switch, oven light bulb, or oven door seal.

Quick tip for saving it

• Take a clear photo of the plate
• Write the model and serial number on your receipt or inside your installation guide
• Keep the numbers handy before ordering parts or checking error codes

Last updated: February 2026

If your Kenmore electric range model 79096021405 oven is not working, start by confirming the range has full power and the oven controls are set correctly. If the cooktop works but the oven will not heat, the most common causes are a failed heating element or a control-related fault.

Quick checks we recommend first

• Make sure the range is not in a power outage situation; the manual warns not to operate during a power failure.
• Verify the cord/plug is seated correctly and the house breaker is fully reset (range circuits can trip one side).
• If the control is beeping and showing an “F” code, clear it using STOP/CLEAR and then retry.
• Confirm you are using the correct bake or broil settings and temperature per the 79096021405 owner’s manual.
• If the oven light is out, it does not stop heating, but it can help confirm whether the control is responding.

Most likely failed parts when the oven will not heat

On this model, no-heat problems usually come down to the bake or broil heating circuit.

Symptom	Most likely cause	What to do next
Bake will not heat, broil may still work	Failed bake element	Inspect for blisters or breaks; consider replacing the frigidaire range bake element 316075103
Broil will not heat, bake may still work	Failed broil element	Inspect broil element for damage; test for continuity
Control beeps, shows F-code	Electronic control fault detected	Clear with STOP/CLEAR; if it returns, troubleshoot per Kenmore 790 range 4-digit error codes
Entire range dead	Power supply issue	Check breaker, outlet, and wiring connections

Why it matters

An oven that will not heat is often a simple electrical or heating-element failure. Verifying power and checking for error codes first prevents unnecessary part replacement and helps you target the correct repair.

Last updated: February 2026

A burner on your Kenmore electric range model 79096021405 usually stops heating because of a power issue, a wrong control setting, a failed surface element, or a bad infinite (surface element) switch. Start with power and settings checks, then inspect the element and its connections.

Quick checks first (fastest fixes)

• Confirm the correct knob is turned on for the burner you are trying to use.
• Check for a house power problem: look for other 240V appliance issues and reset the range breaker (often a double breaker).
• If you have a plug-in style surface element, remove it (when cool) and reseat it firmly.
• Make sure cookware is flat and not badly warped; warped pans can make heating seem weak or uneven.
• If the cooktop was recently cleaned, verify no moisture or cleaner residue is on electrical contacts.

What to inspect (with power off)

Turn off the breaker before opening panels or touching wiring.

• Look for burned, loose, or brittle wires at the surface element receptacle and at the control switch.
• If only one burner fails, the most common causes are the surface element itself or its control switch.
• If multiple burners fail, focus on power supply, terminal block connections, or internal wiring.

Common causes and what they point to

Symptom	Most likely cause	Typical next step
One burner dead, others OK	Failed element or switch	Test/replace element or switch
Burner works only on “HI”	Worn infinite switch	Replace switch
Indicator light behavior is odd	Switch or indicator circuit issue	Inspect switch and indicator wiring
Several burners dead	Power/terminal block/wiring	Check breaker, then wiring connections

Parts that commonly fix a dead burner

If the burner itself is the issue, replacement is often the fix. If the knob control is the issue, the infinite switch is the usual repair.

• Range surface element control switch 316436001
• Oven switch 316436000

Why it matters

A non-working burner is inconvenient, but overheated or loose wiring can also create arcing and heat damage. Catching a failing switch or connection early helps prevent bigger electrical repairs.

For model-specific safety and operating guidance, follow the 79096021405 owner's manual. For electrical hookup and terminal block guidance, use the 79096021405 installation guide.

Last updated: February 2026