Kenmore Elite 11046757801 washer Parts

Your Kenmore Elite washer’s model number is printed on a rating label attached to the cabinet. On Kenmore Elite front-load washers like model 11046757801, the label is most often behind the door opening (door jamb) or along the inside edge of the front panel.

Where to look on model 11046757801

Check these common label locations in this order:

• Behind the washer door, on the door jamb (most common for front-load units)
• Along the inside edge of the front opening near the latch area
• On the back of the control panel area
• On a side panel near the bottom of the cabinet

For diagrams and model identification details, use the 11046757801 owner's manual.

What the model number looks like

Kenmore Elite model numbers are typically a long number string. For this series, you may see a family format like 110.4674### or 110.4675### on the documentation, with the full model printed on the washer’s label.

What you see	What it means	What to do
110.4674### or 110.4675###	Model family/series format	Use the full label number for parts lookup
11046757801	Full model number	Use this exact number when ordering parts

Tips to avoid ordering the wrong part

Use the full model number exactly as printed, then match parts by description and ID.

• Write down the full model number and the full serial number
• Take a clear photo of the rating label before it wears or fades
• If you are replacing a door-related part, match it to the correct component (for example, washer door lock WP8183270 or washer door boot WP8182119)

Why it matters

Kenmore Elite washers share similar styling across multiple series, but internal parts (like the door lock, pump, and control board) can vary by model and production run. Using the exact model number keeps the parts list accurate and prevents returns.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore Elite washer like model 11046757801 when the fix addresses a specific failed part and the total repair cost is clearly less than replacing the washer. This model is designed for years of dependable operation with routine care and occasional repair, so a targeted repair often restores reliable performance.

How we decide if repair makes sense

Use these practical checkpoints before you spend money on parts or labor:

• Confirm the failure is isolated (drain, fill, door lock, belt, leak) rather than multiple systems.
• Compare total repair cost vs. replacement (parts + labor + any follow-up work).
• Check for symptoms that match common, fixable parts (no drain, won’t lock, won’t fill, heavy vibration).
• Factor in downtime: a same-day part like a pump or door lock can be a fast win.
• Consider the washer’s core condition: excessive rust, repeated leaks, or loud bearing noise can push you toward replacement.

Common repairs that are often worth it on this model

These are frequent, straightforward fixes for front-load style Kenmore Elite washers:

Symptom	Likely area	Example part for this model
Won’t drain, water left in tub	Drain system	Pump 280187
Door won’t lock or cycle won’t start	Door latch/lock	Washer door lock WP8183270
Leaks at the door opening	Door seal	Washer door boot WP8182119
Won’t spin well, squeal/burning rubber smell	Drive system	Washer drive belt WPW10388414

What to do first (before buying parts)

1. Use the troubleshooting steps in the 11046757801 owner’s manual to match your symptom to a likely cause.
2. Rule out simple issues: overloaded drum, kinked drain hose, clogged inlet screens, or a door not fully closed.
3. Run a quick visual inspection for water under the washer, loose clamps, or a torn door boot.

Why it matters

A correct diagnosis prevents repeat repairs and protects major components like the motor control board and tub assembly. Spending a little time confirming the failure point often turns an expensive guess into a durable, cost-effective repair.

Last updated: February 2026

Kenmore Elite washers (including model 11046757801) were sold under the Kenmore brand, but they were built by major appliance manufacturers that produced machines to Sears specifications. For many Kenmore Elite washers, Whirlpool was a primary manufacturer, and other makers produced certain Kenmore models in different years.

How to tell who built your specific Kenmore Elite 11046757801

The most reliable way is to use the model and identification information listed in the 11046757801 owner's manual and on the washer’s rating label (typically around the door opening or behind the door area on front-load units).

• Use the full model number 11046757801 when looking up parts and service info
• Check the rating label for a manufacturer code or serial format
• Match the washer’s design to common platform parts (door lock, boot, control)
• Use the manual’s troubleshooting and service sections to confirm platform features
• When ordering parts, match by model number first, not by “who made it”

Why you will see Whirlpool-style parts on this model

Many Kenmore Elite washers share components with Whirlpool-built platforms. On this model page, several common Whirlpool-family part IDs appear, which is consistent with Whirlpool manufacturing for many Kenmore 110-series washers.

Example component on this model	What it does	Example part ID on this page
Washer door lock	Locks the door during wash and spin	WP8183270
Washer door boot	Seals the door opening to prevent leaks	WP8182119
Washer motor control board	Controls motor speed and direction	WP8183196

Why it matters

Knowing the builder helps when comparing designs and troubleshooting patterns, but your model number is what guarantees correct fit. For repairs like leaks, no-drain, or door won’t lock, we recommend starting with the model-specific procedures in the 11046757801 owner's manual and then matching parts by the exact model.

Last updated: February 2026

Yes. Kenmore washers are still sold today, but Kenmore is a brand label rather than a single factory. New Kenmore washers are typically built for Kenmore by major manufacturers, and the exact design varies by model line and model number.

How Kenmore washers are made now

Kenmore-branded laundry products are commonly produced under contract by established appliance makers. That is why two Kenmore washers can look and operate differently even though they share the Kenmore name.

Common things you may notice:

• Different control layouts and cycle names across Kenmore models
• Different parts and service procedures by model series
• Model number prefixes that help identify the manufacturing source
• Different door lock, pump, and control board designs

For your Kenmore Elite washer model 11046757801, we recommend using the model-specific documentation for operation, care, and troubleshooting details in the 11046757801 owner's manual.

Why it matters for parts and repairs

Because Kenmore washers can be built by different manufacturers, the correct replacement part depends on the exact model number, not just the Kenmore brand.

Here are examples of model-specific parts that must match your washer:

• Drain system components such as the pump 280187
• Door sealing components such as the washer door boot
• Safety interlock components such as the washer door lock
• Drive components such as the washer drive belt

Quick check: what to use when you need help

Need	Best reference for model 11046757801	Example part category
Operating instructions and cycle behavior	11046757801 owner's manual	Cycles, options, care
Water not draining or slow drain	Parts list for this model	Pump, tub-to-pump hose
Door will not lock or unlock	Parts list for this model	Door lock, hinge, boot

Why this is important

Using the exact model number 11046757801 prevents ordering the wrong Kenmore Elite washer parts and helps you follow the correct troubleshooting steps for your specific design.

Last updated: February 2026

Yes. Kenmore Elite is Kenmore’s higher-end line, and the Kenmore Elite washer model 11046757801 is built with premium, durability-focused features such as a stainless steel wash drum and advanced wash options like NSF-certified sanitizing temperatures (Steam Sanitize). For feature details and care guidance, use the 11046757801 owner's manual.

What “high end” means for this Kenmore Elite washer

On this model, “Elite” typically shows up as stronger materials, more specialized cycles, and more refined controls than entry-level washers.

Common high-end indicators include:

• Stainless steel drum (designed for long-term durability)
• Sanitizing wash temperature that is NSF-certified for reducing bacteria
• More cycle customization (soil level, wash temp, spin speed)
• Designed for quieter, more stable operation when properly installed and leveled
• Support for laundry-room upgrades like pedestals and stacking (when paired with a matching dryer)

Quick comparison: Kenmore Elite vs standard Kenmore washers

Feature area	Kenmore Elite (like 11046757801)	Standard models (typical)
Drum material	Stainless steel is common	Stainless or coated steel varies
Specialty cycles	Steam Sanitize and similar options are more common	Fewer specialty options
Customization	More settings for temp, soil, spin	Basic setting ranges
Long-term build	More premium components overall	More value-focused builds

Why it matters

If you want better fabric care, stronger cleaning options (including sanitizing temperatures), and a washer designed for years of dependable operation, Kenmore Elite is the right tier to shop. It also makes it easier to justify investing in repairs when a key component wears out.

Parts that commonly support “premium performance”

If performance issues show up (draining, leaking, door problems), these are common repair areas on front-load designs:

• Pump 280187 (drain performance)
• Washer door boot WP8182119 (leaks at the door opening)
• Washer door lock WP8183270 (won’t lock, won’t start)
• Washer water inlet valve WPW10156253 (slow fill, fill errors)

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years. For the Kenmore Elite 11046757801, regular care (especially cleaning and hose checks) helps you reach the high end of that range and reduces common wear issues that shorten washer life. See the 11046757801 owner's manual for model-specific care steps.

Typical lifespan and what affects it

Most washers land in the 10 to 15 year range; real-world lifespan depends on usage and maintenance.

• Loads per week (more cycles equals more wear)
• Overloading (stresses the drive system and suspension)
• Detergent use (too much can cause residue and odors)
• Water quality (hard water can increase buildup)
• Drain performance (slow draining strains the drain system)

Maintenance that extends life (high impact)

The manual for this model includes washer care guidance such as cleaning the washer and checking water inlet hoses.

• Clean the door seal and wipe moisture after use to reduce mildew
• Run a periodic cleaning cycle (or a hot cycle with washer cleaner)
• Inspect water inlet hoses and replace if cracked, bulging, or leaking
• Keep the washer level to reduce vibration and “walking”
• Check pockets and use a mesh bag for small items to protect the pump

Parts that commonly limit washer life

When these parts wear, performance drops and leaks or no-drain symptoms become more likely.

Symptom	Commonly involved part	Example for this model
Won’t drain, drains slowly	Drain pump or drain hose restriction	Pump 280187, washer tub-to-pump hose
Leaks at the door	Door boot (bellows)	Washer door boot WP8182119
Door won’t lock or won’t start	Door lock	Washer door lock WP8183270
Excess vibration or banging	Suspension components	washer suspension spring set

Why it matters

Knowing the typical lifespan helps you decide when maintenance is worth doing versus planning for a major repair. On a front-load Kenmore Elite like model 11046757801, preventing leaks, vibration, and drain problems is the fastest way to protect the tub, motor system, and control components.

Last updated: February 2026

On a Kenmore Elite washer model 11046757801, OE means the washer is not draining properly (a drain error). In most cases, water is staying in the tub because the drain path is restricted or the drain system is not moving water out fast enough.

What usually causes an OE (drain) error

• A clogged drain pump filter or debris in the pump (coins, lint, socks)
• A kinked, pinched, or partially blocked drain hose
• A slow or restricted household standpipe or drain
• A failing drain pump that hums, runs loudly, or will not move water
• Excess suds from too much HE detergent, which can slow draining

Quick checks we recommend first

1. Cancel and reset the cycle; then try Drain/Spin.
2. Check the drain hose for kinks and confirm it is not shoved too far down the standpipe.
3. Inspect the standpipe/drain for slow draining (backing up can trigger OE).
4. Listen for the pump during drain; a loud grind or only a hum often points to a pump obstruction or failure.
5. If the tub still will not drain, plan to inspect the pump area and drain path using the steps in the 11046757801 owner's manual.

Parts that commonly fix OE on this model

If your troubleshooting points to a drain component, these are the most common matches for OE symptoms on model 11046757801:

Symptom	Most likely area	Example part for this model
Won’t drain, pump hums	Pump jammed or failed	Pump 280187
Drains slowly, debris found	Hose restriction/leak	Washer tub-to-pump hose WPW10467168
Intermittent drain issues	Loose hose connection	Clamp WP285655

Why it matters

A true OE drain problem can leave water in the tub, prevent high-speed spin, and cause repeated cycle interruptions. Clearing the restriction early helps prevent odors, oversudsing, and extra wear on the drain pump.

Last updated: February 2026