Kenmore 11024922202 washer Parts

Your Kenmore washer model number is on the model and serial number label; for Kenmore model 11024922202, the manual specifies that label is located under the washer lid. Use the full model number (and serial number) when ordering parts so the fit and wiring match your exact washer.

Where to look on model 11024922202

Check these common label locations in this order:

• Under the lid on the washer cabinet rim or underside of the lid (most common for this model)
• On the rear panel near the power cord entry
• Inside the control console area (less common)

For a picture-style locator and the exact wording format, use the 11024922202 owner’s manual.

What the model number looks like (and why it matters)

Kenmore washer model numbers often start with 110 and may include additional digits. Entering the complete model number helps us match parts like the lid switch, drain pump, or motor coupling to the correct design revision.

Quick guide

What you’re entering	Example format	Used for
Model number	110XXXXXXXX	Parts compatibility and diagrams
Serial number	Letters and numbers	Date/production info for service

Tips to avoid ordering the wrong part

• Copy the model number exactly as printed, including all digits
• Take a clear photo of the label before you start shopping
• If the label is worn, clean it gently with a damp cloth and re-check
• Match the part by name and ID when possible (example: washer lid switch WP3949238)

Why it matters

Kenmore 110-series washers can look similar across years, but internal components (like the lid switch style, pump mounting, or drive system parts) can differ. Using the exact model number prevents returns and speeds up repair.

Last updated: February 2026

To unclog the drain hose on Kenmore washer model 11024922202, we unplug the washer, remove as much water as possible, then clear the blockage from the drain hose and pump path. Most clogs are lint, coins, or small socks trapped at the pump inlet or in the hose bend.

Safety first

• Unplug the washer (or switch off the breaker).
• Turn off both water faucets.
• Have towels and a shallow pan ready; draining can be messy.
• If the washer was running, let the motor cool for a few minutes.

Step-by-step: clear the clog

1. Remove standing water: bail it out, or use a wet/dry shop vac on the standpipe end of the drain hose.
2. Check for kinks and bad routing: the installation instructions require the hooked end to sit in the tub/standpipe without forcing extra hose down the pipe; keep an air gap and rotate the hook to eliminate kinks (details in the installation guide).
3. Access the drain hose connection at the washer: pull the washer forward and locate the hose where it connects at the bottom of the cabinet.
4. Loosen the clamp and remove the hose: squeeze the clamp ears with pliers and slide it back, then twist the hose while pulling it off.
5. Clear the hose and pump inlet: remove debris by hand or with needle-nose pliers; flush the hose with hot tap water.
6. Reinstall correctly: push the hose fully onto the drain connector until it hits the cabinet stop, then reposition the clamp where marked (see the installation guide).

When the hose is clear but it still will not drain

These symptoms usually point to a pump or lid-switch related drain issue:

Symptom	Most common cause	What to check next
Hums but will not drain	Pump jammed	Inspect/replace washer drain pump WP3363394
Drains slowly	Partial blockage	Recheck hose bend and standpipe air gap
Will not spin after draining attempt	Lid switch not closing	Test/replace washer lid switch WP3949238

Why it matters

A properly routed, unclogged drain hose prevents backflow into the tub and helps avoid leaks and overflow. Correct hose installation also reduces repeat clogs caused by kinks and restricted flow.

Last updated: February 2026

Yes, it’s usually worth repairing a Kenmore washer, especially a proven model like Kenmore 11024922202, when the fix restores reliable wash and spin performance for less than the cost of replacement. Common repairs (lid switch, drain pump, coupling, clutch) often deliver years of additional service.

How we decide if repair makes sense

Use these practical checkpoints before spending money:

• Compare total repair cost to replacement cost (parts plus labor if you hire service).
• Prioritize safety and basics first: draining, spinning, and lid/door operation.
• Consider the symptom: a no-drain or no-spin issue is often a straightforward repair.
• Check for multiple failures: several major issues at once can push costs up.
• Factor in downtime: if you need a fast fix, common parts are typically easier to source.

For model-specific operating and service guidance, we recommend checking the 11024922202 owner’s manual.

Repairs that are commonly “worth it” on this washer

These are frequent, high-impact fixes on many Kenmore top-load designs:

• Won’t start or stops mid-cycle: washer lid switch WP3949238
• Won’t drain or leaves water in tub: washer drain pump WP3363394
• Agitates poorly or won’t spin (direct-drive style symptoms): washer motor coupling 285753A
• Spins weakly or slips under load: clutch 285785
• Agitator “ratchets” or doesn’t move clothes well: agitator dog 80040

Quick cost-to-benefit guide

What’s failing	Typical impact	Why repair is often worth it
Lid switch	No start, no spin	Low-to-moderate cost, restores normal operation
Drain pump	No drain, wet clothes	Prevents water damage risk and cycle failures
Motor coupling	No agitation/spin	Common wear item; strong value repair
Clutch	Slow/weak spin	Improves spin speed and water extraction

Why it matters

A washer that drains and spins correctly protects clothing, reduces drying time, and prevents repeated cycle interruptions. The manual also emphasizes safe use and service practices, including avoiding repairs you do not understand and following published instructions. Review the 11024922202 installation guide if you’re also dealing with setup issues like leveling, drain standpipe fit, or water supply connections.

Last updated: February 2026

On Kenmore washer model 11024922202, the F6 E2 (or E2 F6) code points to a communication problem between the user interface (console) and the main control board, or a wiring connection issue between them. Start with a power reset and basic harness checks before replacing parts.

What to do first (quick checks)

• Unplug the washer (or switch off the breaker) for 2 minutes, then restore power and retry the cycle.
• Confirm the outlet is properly grounded and the plug is fully seated (grounding guidance is in the 11024922202 installation guide).
• If the code returns, remove power again and check for a loose console connection or pinched wire harness.
• Look for corrosion or a partially backed-out connector at the control or console.
• If the washer recently vibrated or moved, re-level it; excessive vibration can loosen connections over time.

What the code usually affects

F6 E2 is most often tied to the controls, not the drain system or motor. Use this table to keep troubleshooting focused:

Symptom you see	Most likely area	What we check next
Code appears immediately at start	User interface or harness	Console connector seating, damaged ribbon/harness
Code appears mid-cycle	Main control or intermittent wiring	Harness routing, vibration-related looseness
Random beeping, unresponsive buttons	User interface	Console keypad response, connector condition

When a part replacement becomes likely

If the wiring connections are secure and the code repeats, the failure is typically in one of these components:

• User interface (console) electronics
• Main control board
• Wire harness between console and control

For mechanical issues that can indirectly contribute (movement and vibration), inspect suspension components such as the washer suspension spring WP63907 and confirm the washer is level per the 11024922202 installation guide.

Why it matters

The washer relies on constant communication between the console and control board to fill, agitate, drain, and spin safely. When that communication drops, the washer stops to prevent incorrect operation.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 15 years with normal household use. For your Kenmore 11024922202 washer, consistent care (proper loading, correct water temperature, and preventing freeze damage) helps you reach the upper end of that range; see the 11024922202 owner's manual for model-specific care guidance.

What affects washer lifespan the most

• Overloading: loads should move freely during washing to reduce strain on the drive system.
• Water quality and temperature: hard water and very hot washes can accelerate wear on seals and hoses.
• Drain and spin stress: slow draining or heavy, unbalanced loads increase wear on the clutch and gearcase.
• Cold-weather exposure: operating or storing at or below 32°F (0°C) can leave water inside that can damage components.
• Installation quality: a level floor and correct hookups reduce vibration and premature wear.

Maintenance habits that extend life

Use these habits on the 11024922202 to reduce common failure causes:

Habit	What to do	Why it helps
Load size	Keep loads loose, not packed	Reduces motor, clutch, and gearcase stress
Bleach use	Don’t pour bleach directly on fabrics; wipe spills	Prevents fabric damage and dispenser-area corrosion
Winterizing	Protect the washer from freezing temps	Prevents cracked pump, hoses, and internal water damage
Leveling	Keep the washer level on a sturdy floor	Reduces vibration and suspension wear

When a “worn part” is shortening lifespan

If the washer is otherwise in good shape, replacing a few common wear items can restore performance:

• Won’t spin or agitates poorly: check the washer motor coupling 285753A
• Stops mid-cycle or won’t run: check the washer lid switch WP3949238
• Won’t drain or leaves water in the tub: check the washer drain pump WP3363394

Why it matters

A washer that is nearing end-of-life often shows up as poor draining, weak spin, or inconsistent agitation. Catching those symptoms early can prevent secondary damage (for example, a slipping drive system that overheats or a drain issue that strains the motor).

Last updated: February 2026

The Kenmore washer model 11024922202 is typically listed as a 3.6 cu. ft. washer. That capacity is commonly described as “super capacity” for this style of top-load, agitator washer; it supports full-size loads when you use the highest load size setting.

How to confirm capacity for your exact unit

We recommend verifying the capacity using the model-specific literature for 11024922202, since capacity can vary by series and configuration.

• Check the specifications section in the 11024922202 owner's manual
• Compare your model and serial tag (under the lid) to the manual’s model listing
• If you are matching baskets or tubs, confirm the exact model number before ordering

What 3.6 cu. ft. means in real laundry terms

A 3.6 cu. ft. top-load Kenmore washer is designed for larger, full-size loads.

• Handles bulky mixed loads more easily than “extra large capacity” models
• Lets you wash more towels or jeans per cycle
• Reduces the number of loads for families

Load examples (general guidance)

Load type	Typical examples that fit well	Notes
Towels	Multiple bath towels plus hand towels	Avoid packing tightly for better agitation
Mixed load	Shirts, jeans, and linens together	Balance items to reduce vibration
Bulky items	A comforter (depending on fill)	Use enough water and allow room to move

Why it matters

Capacity affects cleaning performance, cycle time, and wear on drive components. Overloading can lead to poor agitation and spin issues that may involve parts like the washer lid switch WP3949238 or the drive system.

Last updated: February 2026