Kenmore Elite 79575549401 refrigerator Parts

The Kenmore Elite refrigerator model 79575549401 is a bottom-freezer refrigerator; its exact exterior dimensions (width, depth, height) vary by configuration and are listed in the product specifications section of the 79575549401 owner's manual. For planning space, most 33-inch-class bottom-freezer units measure about 33 in W, 30 to 34 in D, and 67 to 70 in H.

How to get the exact dimensions for model 79575549401

We recommend using the manual specs (not a “similar model” listing) so your cabinet opening, door swing, and water line clearance are correct.

• Check the specifications/dimensions section in the 79575549401 owner's manual
• Measure your unit at the widest points (handles and hinges can add width)
• Measure depth with doors closed, then note any extra depth for handles
• Confirm height to the top hinge cover (not just the cabinet)
• Leave clearance for air circulation and for pulling the refrigerator out for service

Quick planning guide (typical ranges)

These ranges help when you are estimating fit before you confirm the exact spec sheet.

Measurement	Typical range for this style	What can change it
Width	~33 in	Door/hinge geometry, trim, handles
Depth	~30 to 34 in	Handles, door thickness, rear clearance
Height	~67 to 70 in	Leveling legs, hinge cover

Why it matters

Correct sizing prevents installation problems like doors hitting cabinets, drawers not clearing, and kinks in the water line. If you’re connecting a water supply for the ice maker, the manual’s water line routing guidance helps you plan enough slack and access behind the refrigerator.

Last updated: January 2026

On Kenmore Elite refrigerator model 79575549401, dH (often shown as Er dH) points to a defrost heating problem: the refrigerator is not warming the evaporator enough during the defrost cycle, so frost can build up and airflow can drop. Use the 79575549401 owner's manual to confirm the display behavior and troubleshooting steps for your exact control panel.

What you’ll usually notice when dH shows up

• Freezer temperature slowly rises or swings
• Frost or ice buildup on the rear freezer panel
• Weak airflow into the fresh food section (warm refrigerator, cold freezer)
• Fan noise changes as ice interferes with airflow
• Water dripping or refreezing after a defrost attempt

Most common causes (and what to check first)

We start with the simplest checks because airflow and frost patterns often point to the root cause.

• Heavy frost on the evaporator cover: indicates a defrost system issue
• Door not sealing well: warm, moist air entering can overwhelm defrost (inspect gaskets and door closure)
• Defrost heater circuit problem: heater, wiring, or connectors
• Control not completing defrost: less common, but possible if other parts test good

If you suspect a failed heater, the model’s listed defrost heater is the lg refrigerator defrost heater 5300JK1005D.

Quick decision guide

What you see	Most likely direction	What we do next
Solid frost sheet behind freezer panel	Defrost system not heating	Check heater and wiring; inspect connectors
No frost, but temps still off	Airflow or sensor/control issue	Check vents, fan operation, settings
Door not closing or gasket gaps	Moisture intrusion	Clean/reshape gasket, confirm door alignment

Why it matters

When defrost heat is not working, frost can block the air passages that move cold air from the freezer to the refrigerator section. That can cause warm food temps, longer run times, and inconsistent ice production.

Helpful related DIY info

For display codes commonly seen on Kenmore 795 bottom-freezer models, use our Kenmore 795 model bottom freezer refrigerator error codes reference to match the exact code format and recommended checks.

Last updated: January 2026

Common problems on the Kenmore Elite 79575549401 bottom-mount refrigerator include weak or no cooling, frost buildup in the freezer, doors that will not close or are hard to open, and ice maker issues like slow ice production or bad-tasting ice. Many fixes start with cleaning, leveling, and checking airflow.

Most common symptoms and what usually causes them

• Not cooling well: dirty condenser coils, blocked vents, or a failed fan motor
• Frost or ice crystals on food: door not sealing, door opened often, or defrost system trouble
• Doors will not close completely: refrigerator not level, bins or shelves out of position, food packages blocking the door
• Doors are difficult to open: dirty or sticky door gaskets, or pressure not equalized after closing
• Ice tastes bad or smells: old ice, unwrapped food odors, or water quality issues
• Slow ice production: freezer not cold enough yet, door left open, or restricted water supply

Quick checks we recommend first (fast, no parts)

1. Clean the condenser coils (this is a top cause of poor cooling and long run times).
2. Confirm doors seal and close: push doors firmly shut; make sure bins and drawers are fully seated.
3. Clean door gaskets and the surfaces they touch; then apply a thin coat of wax as described in the 79575549401 owner's manual.
4. Level the refrigerator if it wobbles or doors drift open.
5. For ice issues: discard the first few batches after installation or service; throw out old ice and rewrap foods.

Parts that commonly relate to these problems

If troubleshooting points to a failed component, these model-matched parts are often involved:

Symptom	Part to check	What it affects
Warm fridge or freezer, poor airflow	Evaporator fan blade 5901JA1021A	Circulates cold air through compartments
Frost buildup, warm temps after icing	Defrost heater 5300JK1005D	Melts frost off the evaporator
Water dispenser or ice maker not filling	Refrigerator valve assembly 5221JB2006K	Controls water flow into the refrigerator

Why it matters

Cooling and ice maker complaints often trace back to airflow, door sealing, or coil cleanliness. Fixing those basics first prevents unnecessary part replacement and helps the compressor and sealed system run under normal load.

Last updated: January 2026