Kenmore 6651350590 compactor Parts

A common problem with the Kenmore 6651350590 trash compactor is that it will not start or complete a cycle because a safety switch, direction/limit switch, or door/drawer latch is not closing properly. Another frequent issue is loud grinding or clicking from worn drive components.

• Won’t start at all: on/off switch, off switch, or a safety interlock is open
• Starts then stops or reverses unexpectedly: top limit/directional switch is failing or misaligned
• Drawer won’t open or won’t stay shut: latch or latch spring issue, or trash is jammed
• Loud grinding/clicking: worn drive gear/chain, loose hardware, or a failing motor
• Bad odors: residue in the drawer, ram area, or bottom pan

1. Make sure the drawer is fully closed and latched.
2. Turn the unit off, wait 1 minute, then turn it back on.
3. Check for a jammed bag or trash caught along the drawer tracks.
4. Inspect the power cord and outlet; reset the kitchen GFCI if it is tripped.
5. If the compactor runs but sounds rough, stop using it until you inspect the drive area.

If the basics check out, these model-compatible parts are common fixes:

Trash compactors rely on multiple safety interlocks and limit switches to prevent the ram from moving when the drawer is not secured. When one switch is weak or misaligned, the compactor can act “dead” even though it has power.

Last updated: February 2026

A Kenmore trash compactor like model 6651350590 typically lasts 10 to 15 years with normal household use. Lifespan depends most on how often you run compaction cycles, how heavily the drawer is loaded, and whether wear items (switches, latches, drive parts) are replaced when symptoms start.

• Keep loads reasonable; don’t pack hard items that can jam the ram.
• If the drawer doesn’t close and latch smoothly, address it early; a worn latch can prevent safe operation.
• Stop using the compactor if it stalls, reverses unexpectedly, or won’t stop at the top; a failing limit/directional switch can damage the drive.
• Reduce friction: a sticking drawer increases strain on the motor and drive chain.
• Clean spills promptly; moisture and residue accelerate corrosion and odors.

• Won’t start or intermittent power: check the switch 675382 and wiring connections.
• Stops at the wrong point, won’t reverse, or won’t stop at top: suspect the trash compactor top limit and directional switch WP777811.
• Drawer won’t stay shut or won’t engage: inspect the latch and spring (wear can mimic bigger failures).
• Grinding, popping, or slipping under load: inspect drive chain, gears, and bearings.
• Excess vibration or slow compaction: motor and mounting hardware can be the root cause.

Knowing the expected service life helps you decide whether to repair or replace. On a 10 to 15 year old unit, replacing a switch or latch is often a cost-effective fix, while repeated drive or motor problems usually signal the compactor is nearing the end of its practical lifespan.

Last updated: February 2026

On Kenmore trash compactor model 6651350590, the model number is printed on a rating label that’s usually on the cabinet frame just inside the drawer opening (behind the drawer/door area). It can also be on a side panel near the bottom front.

• Open the drawer and look along the front frame (left and right sides) where the drawer slides in
• Check the inside edge behind the drawer front (near the latch area)
• Look on the side panel near the bottom (especially if the unit is built-in)
• Check near the kick plate area; you may need to remove the toe panel for a clear view
• If the label is damaged or painted over, use a flashlight and look for faint stamped or printed characters

If your compactor is installed under a counter, these steps help you find the label without fully removing the unit:

We use the exact model number to match Kenmore parts correctly (switches, latch components, drawer hardware, and drive parts). Even small model-number differences can change which parts fit.

If you need the drawer to open so you can access the label, checking the latch mechanism is a good first step; the Kenmore elite trash compactor drawer latch assembly 775665 is one of the common related components for this model.

Last updated: February 2026

If you can’t press the button on your Kenmore 6651350590 trash compactor, the drawer is usually not fully closed or something is blocking it. When the drawer does not seat all the way, the safety interlock will keep the control from starting a cycle.

• Pull the drawer out and remove any trash or debris that could be wedged behind the drawer.
• Reinstall the bag so it is not bunched up at the top edge where it can prevent full closure.
• Push the drawer in firmly until it latches; the latch must fully engage.
• Check the cabinet opening for anything rubbing the drawer front (misaligned kick plate, bent trim).
• If the unit has a key/lockout, make sure it is in the ON/UNLOCK position.

If the drawer closes normally and the button still won’t operate, the problem is typically in the door/drawer safety switch circuit or the on/off switching.

Common parts involved on this model include:

• Trash compactor top limit and directional switch WP777811 (can prevent operation if it is stuck or not actuating)
• Switch 675382 (on/off switch issues can make the control feel “dead”)
• Off switch WP4314961 (a failed off switch can interrupt power to the control circuit)

Trash compactors are designed to never run with the drawer unlatched. That safety design protects you and the cabinet, but it also means a small obstruction or a failing switch can stop the button from working.

Last updated: February 2026