Kenmore 79046693700 electric range Parts

Most Kenmore electric ranges, including model 79046693700, typically last 13 to 15 years with normal use and basic maintenance. Keeping the oven clean, avoiding overheating, and replacing wear items promptly helps you get the full expected lifespan; see the 79046693700 owner's manual for care and cleaning guidance.

Typical lifespan and what affects it

Electric ranges usually reach the end of life because of heat-related wear on components like elements, sensors, and controls.

• Usage frequency (daily cooking wears parts faster than occasional use)
• Heat exposure (frequent high-temp baking or self-clean cycles add stress)
• Cleaning habits (spills left to bake on can damage finishes and parts)
• Power quality (loose connections or surges can shorten control life)
• Timely part replacement (fixing small issues prevents bigger failures)

Common “wear items” you may replace over time

These parts are normal to replace during the life of an electric range.

Part type	What you’ll notice	Example part for 79046693700
Oven light bulb	Light out, flickers	Range oven light bulb 316538904
Oven temperature sensor	Oven temp swings, bakes unevenly	Frigidaire range oven temperature sensor 316217002
Surface element	Burner won’t heat or heats unevenly	Element 316555800

Signs it may be near end-of-life

If you’re seeing multiple symptoms at once, repairs can add up.

• Oven struggles to reach temperature or takes much longer than normal
• Surface elements cycle erratically or stop heating
• Control panel issues (unresponsive keys, random beeping, error codes)
• Repeated tripped breaker or signs of overheating at the power connection

Why it matters

Knowing the typical 13 to 15 year lifespan helps you decide whether to repair or replace. A single part replacement can be cost-effective, but multiple heat-related failures close together often signal the range is nearing the end of its service life.

Last updated: January 2026

On the Kenmore 79046693700 electric range, an oven that “stops working” is usually caused by a power supply issue (tripped breaker or loose terminal connection), a control fault that triggers beeping and an error code, or a failed heating or sensing component that prevents the oven from heating normally. Use the 79046693700 owner’s manual to confirm what the display and elements should do in Bake, Broil, and Self-Clean.

Quick checks that solve many “dead oven” complaints

• Reset the range circuit breaker (many electric ranges use a 240V double breaker; one side tripping can cause odd symptoms).
• Confirm the clock/display is on; if it is blank, check the home outlet and breaker first.
• Press STOP/CLEAR to cancel a stuck cycle or clear a fault and stop beeping.
• Try BAKE 350°F and BROIL; the manual notes the lower element should glow red in Bake and the upper element should glow red in Broil.
• If the oven light is out, replace the bulb so you can see whether elements are glowing; use the range oven light bulb 316538904.

Common causes and what you’ll notice

Symptom	Likely cause	What to do next
Display blank, oven won’t run	Power supply problem, burned connection	Check breaker, cord, and inspect the terminal block 5304409888 for heat damage (power off first).
Oven beeps and shows F1, F3, or F9	Electronic control detected a fault	Press CLEAR; if it returns, service is typically needed. Use Kenmore 790 range 4-digit error codes to interpret codes.
Oven runs but temperature is wrong	Temperature sensor drifting	Test/replace the frigidaire range oven temperature sensor 316217002.
Bake or broil won’t heat	Failed element, wiring issue, control issue	Verify which element should glow in the selected mode; then check wiring and components.

Why it matters

A range can appear “dead” when only part of the 240V supply is missing, and control faults can stop heating for safety. Identifying whether the issue is power, control, or heating feedback prevents unnecessary part replacement.

Last updated: January 2026

On Kenmore electric range model 79046693700, the model and serial number plate is on the oven front frame behind the oven door on some models; on other versions it’s behind the storage drawer. The location is shown in the 79046693700 installation guide.

How to find the model number on this range

• Open the oven door and look on the front frame around the door opening.
• Check both the left and right sides of the frame for a metal or foil rating plate.
• If it’s not there, pull the storage drawer out and look on the frame behind the drawer.
• Record the model number and serial number exactly as printed.
• Use that information when ordering parts or scheduling service.

What to write down

Label item	What it looks like	What we use it for
Model number	Numbers (example: 79046693700)	Matching parts diagrams and compatible replacements
Serial number	Letters and numbers	Identifying the production run for service accuracy
Lot number/letter (if shown)	Single character	Additional identification for parts inquiries

Why it matters

Kenmore ranges in the 790 series can share similar styling, but parts such as a surface element, control board, or oven temperature sensor vary by exact model and production details. Using the rating plate info prevents ordering the wrong part.

Last updated: January 2026