Maytag LAW9704AAE washer/dryer Parts

You can order replacement parts for your Maytag washer model LAW9704AAE right here by matching your symptom or part description to the correct component, then ordering by part ID. Common wear items for this washer include the lid switch, drive belt, hoses, and clamps.

Best way to order the right part (and avoid returns)

• Confirm the full model number on the washer’s model tag: LAW9704AAE
• Identify the problem first (no spin, no drain, won’t start, leaking)
• Match the part by part name + part ID (not just a look-alike)
• Compare your old part’s markings and connector style before checkout
• Order any one-time-use items you may need (clamps, fasteners) at the same time

Popular Maytag LAW9704AAE parts customers replace

If you are troubleshooting a no-start or no-spin condition, the lid switch is a common first check:

• Lid switch W10820036
• Washer drive belt 12112425
• Inlet hose W11629055

Quick troubleshooting guide (what to order depends on the symptom)

Symptom	Most common area to check	Example part for LAW9704AAE
Won’t start or stops when lid opens	Lid safety circuit	Lid switch W10820036
Motor runs but basket won’t spin well	Belt and drive system	Washer drive belt 12112425
Leaking at fill or during fill	Fill hoses and clamps	Inlet hose W11629055

Why it matters

Ordering by the exact LAW9704AAE model and the correct part ID helps ensure proper fit, correct electrical connections (for switches), and the right length and routing (for hoses and belts).

Last updated: February 2026

Most Maytag washers average 10 to 13 years of service life with normal household use and basic maintenance; many last longer when loads are kept reasonable and wear items are replaced as they fail. For your Maytag LAW9704AAE, lifespan is driven more by usage and upkeep than by the model number itself.

Typical lifespan ranges

Washer type	Typical lifespan	What usually ends it
Top-load, belt-drive style (common on older Maytag designs)	10 to 13 years	Bearings, belt, lid switch, leaks
Heavy-use household (large family, daily loads)	7 to 10 years	Drive system wear, tub seal/bearing noise
Light-use household (few loads per week)	12 to 15+ years	Age-related leaks, electrical wear

What to do to reach the high end of the range

• Avoid chronic overloading; it accelerates belt, bearing, and suspension wear.
• Use the right detergent amount; excess suds can contribute to drain and odor issues.
• Level the washer; out-of-level operation increases vibration and bearing stress.
• Inspect hoses and clamps periodically for seepage and corrosion.
• Fix small problems early (a slipping belt or intermittent lid switch) before they cascade.

Parts that commonly affect “how long it lasts”

These are frequent wear or failure points that can stop a washer even when the rest is fine:

• Lid safety circuit: lid switch W10820036 or washer lid switch WP207166
• Drive system wear: washer drive belt 12112425
• Vibration and noise contributors: tub bearings and related hardware

Why it matters

A washer that is maintained and repaired promptly often costs far less per year to own. Replacing a single wear part (like a lid switch or drive belt) can restore normal washing and spinning and help you get several more years out of the LAW9704AAE.

Last updated: February 2026

Yes, it’s usually worth fixing a Maytag washer when the problem is a common, lower-cost failure (like a lid switch or belt) and the machine is otherwise in good shape; for the Maytag LAW9704AAE, repairs that stay under about half the cost of a comparable replacement are typically the best value.

Quick way to decide (cost vs. condition)

Use these checkpoints before you buy parts or schedule service:

• Repair cost target: keep the total repair (parts + labor) under 50% of replacement cost.
• Failure type: electrical interlocks and wear items are good repair candidates; major drive or tub issues are not.
• Overall condition: no chronic leaks, no severe rust, no repeated breakdowns.
• Performance: it fills, agitates, drains, and spins normally aside from the current symptom.
• Downtime: if you need a fast fix, start with the most common, easiest-to-test parts.

Repairs that are commonly “worth it” on LAW9704AAE

These are typical, high-impact fixes that often restore normal operation:

• Replace a failed lid switch such as the lid switch W10820036.
• Replace a worn or slipping belt such as the washer drive belt 12112425.
• Tighten or replace a loose clamp (helps with minor seepage and hose security).
• Repair a damaged wire or terminal (especially near the lid switch harness).

Repairs that often push toward replacement

If you see these symptoms, the repair can become labor-heavy or cascade into multiple parts:

• Loud roaring/grinding during spin (often bearing or tub-related)
• Water leaking from the tub area (not just hoses)
• Burning rubber smell plus repeated belt issues (possible pulley or drive alignment problems)
• Multiple major symptoms at once (drain + spin + agitation)

Situation	Typical recommendation	Why
Won’t spin but otherwise runs	Repair first	Often a lid switch or belt issue
Minor leak at a hose connection	Repair first	Usually clamp or hose related
Persistent loud bearing noise	Consider replacement	High labor and multiple parts risk

Why it matters

A targeted repair on the LAW9704AAE can extend the washer’s life at a fraction of replacement cost, but major mechanical failures can turn into a chain of repairs. Starting with the most common wear parts keeps the decision simple and cost-controlled.

Last updated: February 2026

The most common Maytag washer problem is a no-spin or no-drain condition. On the Maytag LAW9704AAE, we most often trace that to a lid switch that is not closing, a worn drive belt, or a drain restriction that keeps the washer from completing the cycle.

Quick checks we recommend first

• Confirm the lid closes firmly; if the washer stops when you lift the lid, the lid switch circuit is critical.
• Redistribute the load; a severely unbalanced load can stop or slow spin.
• Check the drain hose for kinks, crushing, or a clogged standpipe.
• Look for a loose, glazed, or broken belt under the cabinet.
• Listen for the motor running but no basket movement (often belt or drive system related).
• If it fills but will not agitate or spin, focus on the lid switch and belt before anything else.

Parts that commonly fix “won’t spin” on LAW9704AAE

If your symptoms match, these are frequent repair wins for this model:

Symptom	Most likely area	Common fix for this model
Won’t spin, motor runs	Drive system	Replace washer drive belt 12112425
Won’t spin, acts “dead” when lid is open	Safety interlock	Test/replace lid switch W10820036 or washer lid switch WP207166
Drains slowly or not at all	Drain path	Clear hose/standpipe; inspect clamps like WP285655/WP3367052

Why it matters

A washer that cannot drain or spin leaves clothes soaking wet and can strain the motor and belt. Fixing the root cause early (especially a failing lid switch or slipping belt) prevents repeat shutdowns and reduces wear on the drive components.

Helpful DIY skill for this repair

When diagnosing a lid switch or wiring issue, we use basic electrical testing to confirm the switch opens and closes correctly. See how to use a multimeter to test electrical parts video.

Last updated: February 2026