Amana NTW4501XQ0 washer Parts

For an Amana NTW4501XQ0 washer, a hard reset is usually a simple power reset: unplug the washer (or switch off the breaker) for about 5 minutes, then restore power and start a cycle. This clears many control glitches and restores normal operation.

• Press Power/Cancel to stop the current cycle.
• Unplug the washer from the outlet (or turn the breaker off).
• Wait 5 minutes.
• Plug the washer back in (or turn the breaker on).
• Lift and close the lid once, then select a cycle and press Start.

A calibration routine re-syncs the control with key components (motor, actuator, lid lock) after certain repairs or repeated error behavior. Follow the exact button or dial sequence shown in your installation guide, then run the calibration or test cycle described there.

• The washer will not start or stops mid-cycle
• Agitation or spin seems weak or inconsistent
• The lid locks but the cycle will not continue
• You recently replaced a drive or control part

A reset will not fix a failed part, but it can help you narrow the problem. If symptoms return right away, these model-matched parts are common suspects:

• Lid will not lock or unlock: washer lid lock assembly W10404050
• Will not drain or leaves water in tub: washer drain pump assembly WPW10276397
• Will not shift between agitate and spin: washer actuator WPW10006355
• Noisy, slipping, or weak spin: washer drive belt WPW10006384

A proper hard reset can clear a temporary control fault without replacing parts. If the same failure returns after a reset, it usually points to a mechanical issue (belt, cam, suspension) or an electrical issue (lid lock, actuator, control).

You can order NTW4501XQ0 replacement parts from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

The Amana NTW4501XQ0 top-load washer has a 3.4 cu. ft. capacity. That number describes the washer’s tub volume; for best cleaning and smooth spinning, load items loosely and follow the cycle and loading guidance in the NTW4501XQ0 owner's manual.

Capacity is a sizing guide, not a fill-to-the-top target. To get better wash action and reduce out-of-balance issues:

• Load items loosely; do not pack or compress laundry
• Keep the top of the load below the tub rim
• Mix large and small items (towels plus smaller pieces)
• Choose the right cycle and water temperature for the fabric
• If the washer thumps or walks during spin, pause and redistribute the load

Use these as practical starting points; bulky items take up space fast.

Loading to match the NTW4501XQ0’s capacity helps it agitate and rinse properly, and it reduces strain on drive and spin components. Chronic overloading commonly leads to vibration, longer cycle times, and faster wear on parts like the washer drive belt WPW10006384.

You can order model-matched replacement parts from the parts list for this washer, or search by model number on Sears PartsDirect.

Last updated: February 2026

Your Amana washer’s model number is printed on the model and serial tag on the cabinet. On NTW4501XQ0, check around the lid opening and the underside of the lid; the tag is easiest to read with the lid open and good lighting.

• Open the washer lid and look along the rim of the tub opening.
• Check the underside of the lid near the hinge area.
• Look on the cabinet near the rear of the lid opening.
• If the tag is smudged, wipe it gently with a damp cloth and dry it.

Record both the model number and serial number; they are used to match the correct parts list, diagrams, and service information.

Small design changes can affect which parts fit your washer (for example, a lid lock, water inlet valve, or drive components). Using the full model number helps ensure you get the right replacement part the first time.

If you want a visual reference for your washer and its identification information, use the NTW4501XQ0 installation guide.

Last updated: March 2026