Whirlpool DU1014XTXB0 undercounter dishwasher Parts

Yes. Whirlpool makes dishwashers, including the Whirlpool DU1014XTXB0 undercounter dishwasher, and we support it with model-specific parts, troubleshooting, and documentation in the DU1014XTXB0 owner's manual.

What this means for parts and service

When Whirlpool is the manufacturer, you can match replacement parts and repair steps to the exact model number on the rating label (typically inside the door area).

• Use the full model number DU1014XTXB0 when ordering parts like a heating element, drain pump, or door seal.
• Follow Whirlpool’s cycle and operation guidance before replacing parts.
• If the dishwasher will be stored seasonally, shut off water and power; winterize if freezing is possible.
• For “won’t run” symptoms, confirm the door is fully closed and latched, and verify household power.
• For “won’t drain” symptoms, check and clean the drain air gap (if your installation uses one).

Quick checks Whirlpool recommends first

These are common, fast checks that often prevent unnecessary part replacement.

Symptom	What to check first	Why it helps
Won’t start	Door closed and latched	The control will not run with an unlatched door
Stops mid-cycle	Household breaker or fuse	Restoring power can resume normal operation
Not draining well	Drain air gap (if installed)	A clogged air gap blocks drain flow

Why it matters

Dishwashers are model-specific machines. Confirming Whirlpool as the brand and using DU1014XTXB0 helps ensure the right fit, correct electrical ratings, and proper installation details for parts like the drain hose, water inlet valve, and control board.

Last updated: February 2026

On the Whirlpool DU1014XTXB0 dishwasher, most “error” situations clear by canceling the cycle and restoring normal control operation. Start by making sure no cycle is actively running, then use the reset steps in your DU1014XTXB0 owner's manual to return the control to a ready state.

Quick reset steps to try first

• Press CANCEL/DRAIN (or the model’s cancel function) and let the dishwasher drain completely.
• Wait 1 minute with the door closed.
• Press START/RESUME to restart the last cycle, or select a new cycle.
• If the controls are unresponsive, turn Control Lock off (see below).
• If the dishwasher still will not respond, shut off power at the breaker for 2 minutes, then restore power.

If the controls are locked (common “won’t reset” cause)

Your DU1014XTXB0 uses the 4-HR DELAY button for Control Lock.

• To turn Control Lock ON: press and hold 4-HR DELAY for at least 3 seconds.
• To turn Control Lock OFF: press and hold 4-HR DELAY for at least 3 seconds.

When Control Lock is lit, the buttons are disabled, so the dishwasher can look like it has an error even when it is simply locked.

What different “error-like” symptoms usually mean

Symptom on DU1014XTXB0	What it usually indicates	What to do next
Dishwasher stops or won’t start	Door not latched, power issue, or paused cycle	Confirm door latches; check breaker/fuse; press START/RESUME
Clean light flashing	Service-needed condition	Reset power, then run a test cycle; service if it returns
Won’t fill	Float stuck up	Press float down to release, then retry

Why it matters

Resetting the control clears a stuck cycle state and helps you separate a simple control lock or pause from a real problem like a fill issue, drain issue, or power interruption.

If you suspect a power problem inside the dishwasher (no lights, dead panel), testing the internal fuse is a common next step; our fuse W10258275 is the model-matched part used in the power circuit.

Last updated: February 2026

On a Whirlpool dishwasher like model DU1014XTXB0, an F4 code commonly points to a drain problem (the dishwasher is not draining properly). Start by canceling the cycle, then check for a blockage in the drain path and confirm the drain system is installed correctly per the DU1014XTXB0 owner's manual.

What to check first (fast, no parts)

• Press Cancel/Drain (or the model’s cancel function) and listen for the drain pump running.
• Check the sink/disposer connection for a clog (especially if a disposer was recently installed).
• If you have a drain air gap, clean it; a blocked air gap can stop draining.
• Inspect the bottom of the tub for standing water and remove any debris you can reach safely.
• Verify the drain hose is not kinked, crushed, or looped incorrectly under the sink.

Likely causes and the most common fixes

Symptom	Most likely cause	What usually fixes it
Hums but won’t drain	Jammed pump or blockage	Clear obstruction; inspect pump inlet
Drains slowly	Clog in hose/air gap	Clean air gap; clear hose/disposer port
No drain sound at all	Power issue to pump or control	Check power supply; inspect wiring and safety devices

Parts that often solve an F4 drain issue

If the drain path is clear and the dishwasher still will not drain, these model-matched parts are common next steps:

• Dishwasher drain pump WPW10348269 (failed pump motor or damaged impeller)
• Dishwasher drain hose 8269144A (collapsed hose, internal restriction, or damaged end)
• Fuse W10258275 (if the dishwasher is dead or stops unexpectedly)

Why it matters

A dishwasher that cannot drain can leave dirty water in the sump, reduce wash performance, and cause the cycle to stop mid-program. Fixing the drain path first prevents unnecessary part replacement and helps protect the pump and motor.

Last updated: February 2026