Whirlpool DU1014XTXB0 undercounter dishwasher Parts

Yes. Whirlpool makes dishwashers, including the Whirlpool DU1014XTXB0 undercounter dishwasher, and we support it with model-specific parts, troubleshooting, and documentation in the DU1014XTXB0 owner's manual.

When Whirlpool is the manufacturer, you can match replacement parts and repair steps to the exact model number on the rating label (typically inside the door area).

• Use the full model number DU1014XTXB0 when ordering parts like a heating element, drain pump, or door seal.
• Follow Whirlpool’s cycle and operation guidance before replacing parts.
• If the dishwasher will be stored seasonally, shut off water and power; winterize if freezing is possible.
• For “won’t run” symptoms, confirm the door is fully closed and latched, and verify household power.
• For “won’t drain” symptoms, check and clean the drain air gap (if your installation uses one).

These are common, fast checks that often prevent unnecessary part replacement.

Dishwashers are model-specific machines. Confirming Whirlpool as the brand and using DU1014XTXB0 helps ensure the right fit, correct electrical ratings, and proper installation details for parts like the drain hose, water inlet valve, and control board.

Last updated: February 2026

On the Whirlpool DU1014XTXB0 dishwasher, most “error” situations clear by canceling the cycle and restoring normal control operation. Start by making sure no cycle is actively running, then use the reset steps in your DU1014XTXB0 owner's manual to return the control to a ready state.

• Press CANCEL/DRAIN (or the model’s cancel function) and let the dishwasher drain completely.
• Wait 1 minute with the door closed.
• Press START/RESUME to restart the last cycle, or select a new cycle.
• If the controls are unresponsive, turn Control Lock off (see below).
• If the dishwasher still will not respond, shut off power at the breaker for 2 minutes, then restore power.

Your DU1014XTXB0 uses the 4-HR DELAY button for Control Lock.

• To turn Control Lock ON: press and hold 4-HR DELAY for at least 3 seconds.
• To turn Control Lock OFF: press and hold 4-HR DELAY for at least 3 seconds.

When Control Lock is lit, the buttons are disabled, so the dishwasher can look like it has an error even when it is simply locked.

Resetting the control clears a stuck cycle state and helps you separate a simple control lock or pause from a real problem like a fill issue, drain issue, or power interruption.

If you suspect a power problem inside the dishwasher (no lights, dead panel), testing the internal fuse is a common next step; our fuse W10258275 is the model-matched part used in the power circuit.

Last updated: February 2026

On a Whirlpool dishwasher like model DU1014XTXB0, an F4 code commonly points to a drain problem (the dishwasher is not draining properly). Start by canceling the cycle, then check for a blockage in the drain path and confirm the drain system is installed correctly per the DU1014XTXB0 owner's manual.

• Press Cancel/Drain (or the model’s cancel function) and listen for the drain pump running.
• Check the sink/disposer connection for a clog (especially if a disposer was recently installed).
• If you have a drain air gap, clean it; a blocked air gap can stop draining.
• Inspect the bottom of the tub for standing water and remove any debris you can reach safely.
• Verify the drain hose is not kinked, crushed, or looped incorrectly under the sink.

If the drain path is clear and the dishwasher still will not drain, these model-matched parts are common next steps:

• Dishwasher drain pump WPW10348269 (failed pump motor or damaged impeller)
• Dishwasher drain hose 8269144A (collapsed hose, internal restriction, or damaged end)
• Fuse W10258275 (if the dishwasher is dead or stops unexpectedly)

A dishwasher that cannot drain can leave dirty water in the sump, reduce wash performance, and cause the cycle to stop mid-program. Fixing the drain path first prevents unnecessary part replacement and helps protect the pump and motor.

Last updated: February 2026