Kenmore Elite 11045976401 washer Parts

To force your Kenmore Elite washer model 11045976401 to drain, we use the control-panel drain routine: press PAUSE/CANCEL, select DRAIN & SPIN, then press and hold START for about 1 second. This drains the tub and unlocks the door after the spin finishes (see the 11045976401 owner's manual).

Fast steps to drain it now

• Press PAUSE/CANCEL once to stop the cycle.
• Select DRAIN & SPIN.
• Press and hold START (about 1 second) to begin draining.
• Wait for the cycle to complete; the door unlocks when the spin is done.
• Remove items only after the door unlocks.

If it will not drain (common causes)

A no-drain problem is usually a restriction in the drain path or a failed drain component.

• Check the drain hose for kinks, crushing, or being pushed too far into the standpipe.
• Make sure the drain hose has an air gap at the standpipe or laundry tub so it can flow properly.
• If you hear the pump running but water moves slowly, a clog in the tub-to-pump hose is common.
• If you hear a hum and no water movement, the pump may be jammed or failing.

Parts that often fix drain problems

Symptom	What it points to	Part on this model page
Slow drain, debris found in hoses	Restriction between tub and pump	Washer tub-to-pump hose WPW10467168
No drain, pump not moving water	Failed or jammed pump	Water pump 280187
Leaks after hose work	Loose or weak clamp	Clamp WP285655

Why it matters

Forcing the washer to drain the right way protects the door lock system and helps prevent overflow. It also confirms whether the issue is a control setting problem or a true drain-path or pump failure.

Last updated: February 2026

To reset your Kenmore Elite washer model 11045976401, we recommend canceling the current cycle using the PAUSE/CANCEL button, then restarting the washer. This clears most control glitches and gets the washer back to a normal starting state; see the steps in the 11045976401 owner's manual.

Quick reset steps (most common)

• Press PAUSE/CANCEL twice to cancel the cycle.
• Wait for the washer to power down.
• If the door is locked, allow time for the washer to drain automatically (high water level or hot water can delay unlocking).
• Select your desired cycle again.
• Press and hold START for about 1 second to begin.

If the washer is unresponsive

If the control panel is frozen or buttons do not respond, do a power reset.

• Press PAUSE/CANCEL once.
• Unplug the washer (or switch the breaker off).
• Wait 1 minute.
• Restore power.
• Select a cycle and press and hold START for about 1 second.

What “reset” does (and does not) do

Action	What it affects	What it will not fix
PAUSE/CANCEL twice	Cancels the current cycle and powers the washer down	Broken door latch, failed drain pump, or a leak
Unplug for 1 minute	Clears a temporary control lockup	Repeated error codes caused by a failing part

Why it matters

A proper reset prevents repeated mid-cycle stops and helps you confirm whether the issue is a one-time control glitch or a repeatable problem (like draining, door locking, or filling). If the washer frequently stops and needs resetting, we focus next on the systems that commonly interrupt cycles: door lock, draining, and water fill.

Parts that commonly relate to “won’t start” or “won’t unlock” symptoms

• Washer door lock assembly WP8182634 (door won’t lock or unlock)
• Washer door strike WP8181651 (door latch alignment issues)
• Washer water inlet valve WP8181694 (won’t fill, long fill)
• Water pump 280187 (won’t drain, door stays locked)

If you’re seeing an error code along with the problem, use our Kenmore 110 high efficiency front load washer error codes guide to narrow the cause before replacing parts.

Last updated: February 2026

On the Kenmore Elite washer model 11045976401, the model number is printed on a rating label that’s typically easiest to spot when you open the door; it’s commonly on the door opening (door jamb) or just behind the door. For exact label locations and illustrations, use the 11045976401 owner's manual.

Most common places to check

Look for a sticker or metal tag with the model number and serial number in these spots:

• Inside the door opening on the cabinet frame (door jamb)
• Behind the door on the front panel area near the opening
• Along the side of the main cabinet near the bottom front edge
• On the back of the control panel area (less common on front-load models)

What the label looks like

The rating label usually includes more than just the model number. Expect to see:

• Model number (for example, 11045976401)
• Serial number
• Electrical information (voltage/amps)
• Brand name (Kenmore)

What you see	What it means	Why you need it
Model number	Identifies the exact washer design	Ensures you get the right parts list and diagrams
Serial number	Identifies production run details	Helps match revisions when ordering certain parts

Why it matters

Kenmore model numbers can look very similar, but small differences change the correct replacement parts. Using the exact model number helps us match items like the washer door boot WP8182119 or the washer door lock assembly WP8182634 to your washer.

Quick tips before you search parts

• Write the model number exactly as shown (include all digits)
• Take a clear photo of the label for reference
• If the label is worn, check for a second label near the lower cabinet edge

To order parts for your washer, start with the parts list for model 11045976401 on this page; you can also search by model number on Sears PartsDirect.

Last updated: February 2026