Kenmore 10659267990 side-by-side refrigerator Parts

Kenmore Elite dimensions vary by the exact model and style (side-by-side, French door, top freezer). For your Kenmore 10659267990 side-by-side refrigerator, the most reliable way to confirm the exact height, width, and depth is to use the specifications section in the owner's manual.

Typical Kenmore Elite refrigerator dimensions (what to expect)

Even within “Kenmore Elite,” sizes differ mainly by capacity and door style. Most full-size refrigerators fall into these common ranges:

• Width: 32 1/2 to 36 inches
• Height (to top of hinge): 66 to 71 inches
• Depth (cabinet): 28 to 34 inches
• Depth (with handles): often 1 to 3 inches deeper than cabinet depth
• Clearance needed: typically 1 inch on top and 1/2 inch on sides (more if your manual specifies)

How to measure your refrigerator correctly

Use a tape measure and record in inches. Measure twice, especially if you are fitting into a tight opening.

• Width: widest point of the cabinet (not the doors), then measure again including handles
• Height: floor to top of hinge cover (or highest point)
• Depth: back of cabinet to front edge of doors, then again including handles
• Door swing clearance: measure how far doors extend when opened

Quick dimension checklist (write these down)

Measurement	What to include	Why it matters
Width	cabinet, then handles	fit between cabinets/walls
Height	to top hinge	fit under soffits/cabinets
Depth	doors, then handles	walkway clearance
Clearance	sides/top/back	airflow and door operation

Why it matters

Correct dimensions prevent installation problems like doors hitting walls, poor airflow that hurts cooling performance, and difficulty removing bins or the ice container.

If you are replacing a damaged storage component while you measure, common fit-related parts for this model include the refrigerator door bin WP2156022 and the refrigerator crisper pan WP2188656. For additional parts by model number, you can also search on Sears PartsDirect.

Last updated: February 2026

For Kenmore side-by-side refrigerator model 10659267990, we clean the condenser coils by unplugging the refrigerator, then vacuuming dust from the coils either behind the base grille (front) or on the back of the cabinet, depending on your coil location. See the steps in the owner's manual.

Before you start (safety and access)

• Unplug the refrigerator (or disconnect power at the breaker).
• Protect the floor with cardboard or a towel if you need to pull the unit out.
• Use a vacuum with an extended attachment; a soft coil brush also helps.
• Avoid abrasive cleaners or harsh chemicals around the cabinet and grille.
• Keep pets and kids away from the work area.

Cleaning steps by coil location

Your 10659267990 can be set up in one of these common styles:

Coil location	What you remove/move	How we clean it
Behind the base grille (front)	Remove the base grille	Vacuum coils when dusty or dirty; reinstall grille
On the back of the refrigerator	Pull refrigerator away from wall	Vacuum coils; roll unit back and leave about 1 inch clearance

Style 1: Coils behind the base grille

• Remove the base grille.
• Vacuum the condenser coils thoroughly.
• Reinstall the base grille.

Style 2: Coils on the back

• Pull the refrigerator out from the wall.
• Vacuum the coils and surrounding area.
• Roll the refrigerator back into place; leave about 1 inch between the cabinet back and the wall.
• Check that the refrigerator is level, then restore power.

How often we recommend cleaning

• Clean coils regularly.
• In many homes, coils may need cleaning as often as every other month (especially with pets, heavy dust, or a high-use kitchen).

Why it matters

Dirty condenser coils reduce heat transfer, which makes the compressor work harder. That can increase energy use and contribute to warm temperatures, longer run times, and poor overall cooling performance.

Last updated: February 2026

Kenmore is a brand name; the Kenmore 106. model prefix (including model 10659267990) identifies a Whirlpool-built refrigerator. That means your Kenmore 10659267990 side-by-side refrigerator was manufactured for Sears under the Kenmore name by Whirlpool.

How we identify the maker for model 10659267990

We use the model prefix system that Kenmore has historically used across many appliances.

• 106 prefix: Whirlpool manufacturing source
• The rest of the digits: configuration and production details for that specific refrigerator
• This is why many replacement parts for Kenmore 106 models cross to Whirlpool-sourced components

For model-specific details (features, controls, care, and service info), use the owner's manual.

Why this matters when buying parts

Knowing the manufacturing source helps you match the correct style of parts (ice maker, water system parts, door hardware) and troubleshoot common Whirlpool-built side-by-side designs.

Common Whirlpool-built Kenmore 106 parts you may see on this model

System	Example part on this model page	What it affects
Ice maker	Ice maker assembly - refrigerator ice maker by Whirlpool 4317943	Ice production and harvesting
Water supply	Refrigerator inlet valve W10408179	Water to dispenser and ice maker
Temperature control	Refrigerator thermostat WP2198202	Cooling regulation
Defrost safety	Refrigerator defrost bi-metal WPW10225581	Prevents overheating during defrost

Quick tips to confirm you are ordering the right part

• Match the full model number exactly: 10659267990
• Compare the part name and ID to your symptom (no ice, no water, warm fridge, etc.)
• Use the diagrams and part list for this model first; then broaden your search on Sears PartsDirect if needed
• If you are troubleshooting ice or water issues, start with the water supply and valve before replacing the ice maker

Last updated: February 2026

On Kenmore model 10659267990, a bad compressor usually shows up as poor cooling with the unit running a lot, unusual clicking as it tries to start, or the compressor being very hot after repeated start attempts. Before condemning it, rule out airflow and defrost issues using the 10659267990 owner's manual.

Quick checks before blaming the compressor

• Confirm the refrigerator and freezer temperatures are set correctly.
• Listen for normal cycling sounds; some clicking and longer run times can be normal on efficient units.
• Clean dusty condenser coils; dirty coils reduce heat transfer and make the compressor work harder.
• Make sure doors close fully and gaskets seal all the way around.
• Check for strong airflow from the evaporator fan area; weak airflow can mimic compressor failure.

Symptoms that strongly point to a compressor or sealed-system problem

These signs together usually indicate a compressor that is failing or a sealed-system issue (compressor, refrigerant, or internal tubing):

What you notice	What it often means
Fridge runs constantly but temperatures stay warm	Compressor not pumping effectively or sealed-system restriction
Repeated clicking every few minutes	Start device overload tripping or compressor struggling to start
Compressor is extremely hot to the touch after trying to run	High load condition, poor heat rejection, or internal compressor problem
Very little sound or vibration from compressor when it should be running	Compressor not starting (electrical or mechanical failure)

Why coil and airflow checks matter

This refrigerator is designed to run efficiently, so it may run longer than older models and make different sounds. When condenser coils are dirty or airflow is restricted, the compressor can overheat and short-cycle, which looks like a “bad compressor” even when the root cause is maintenance or airflow.

When a part replacement is the likely next step

If you have verified good airflow and clean coils but cooling is still poor, compressor replacement is a sealed-system repair. For this model, the compressor is available as refrigerator compressor W10309990. For other repair parts and diagrams for model 10659267990, order from the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

On Kenmore side-by-side refrigerator model 10659267990, the model and serial number label is located on the inside wall of the refrigerator (fresh food) compartment. Open the fresh food door and look along the interior side wall for the rating label.

Where to look first (fast checklist)

• Open the refrigerator (fresh food) door, not the freezer door
• Check the inside wall of the refrigerator compartment
• Look near the upper side wall or mid-level side wall where labels are easiest to read
• Use a flashlight; the label can be low-contrast or partially hidden by shelves
• Write down the full model number and serial number exactly as shown

What the label looks like

Most Kenmore side-by-side units use a printed rating label that includes:

• Model number (for this unit, it begins with 106.)
• Serial number
• Electrical information (voltage/amps)
• Safety and certification markings

Quick reference table

What you need	Where it appears	Why you need it
Model number	Inside wall of refrigerator compartment	Ensures you get the correct parts list and diagrams
Serial number	Same label as model number	Helps match production details for certain parts
Purchase date (your records)	Not on the label	Useful for service history and maintenance tracking

Why it matters

We use the exact model number to match the correct Kenmore parts diagrams and compatible replacement parts (for example, an ice maker assembly or water inlet valve). Even small model-number differences can change the correct part fit.

If the label is hard to read

• Clean the label gently with a damp cloth and dry it
• Take a close-up photo and zoom in
• If the label is damaged, use the model number location guidance in the owner's manual

You can also search parts by model number on Sears PartsDirect.

Last updated: February 2026