Kenmore 11016922501 washer Parts

The Kenmore washer model 11016922501 is a full-size top-load design; washers in this class are typically about 3.2 to 3.6 cu. ft. For the exact rated capacity for your unit, check the specifications section in the 11016922501 owner's manual.

Use these quick checks to get the right number for your Kenmore 11016922501:

• Look for a “Capacity” or “Specifications” section in the 11016922501 owner's manual
• Check the model tag (often under the lid or on the rim) and match it to the manual
• If the manual lists multiple versions, use the one that matches your series/revision
• Use load guidance in the manual to avoid overfilling even when you know the cu. ft.

The manual’s operating guidance is the best way to load this washer correctly:

• Load items loosely, not packed down
• Keep the load evenly distributed around the basket
• Do not let the load height exceed the top row of basket holes (helps prevent vibration)
• Mix large and small items to reduce out-of-balance spinning

Capacity affects cleaning and spin performance. When a top-load washer is overloaded, clothes cannot circulate properly; that leads to poor cleaning, more vibration, and more wear on drive components.

Last updated: February 2026

Kenmore model numbers are read left to right: the first 3 digits identify the manufacturer group, and the remaining digits narrow down the exact product and its feature set. For your Kenmore washer model 11016922501, the 110 prefix is the key identifier to start with.

On Kenmore washer 11016922501, we look for the model and serial number label under the washer lid. Recording it exactly helps ensure the parts list matches your machine.

• Lift the lid and look around the rim of the opening
• Write down the full model number (all digits)
• Write down the serial number (letters and numbers)
• Keep the purchase date with your records
• Use the full model number when ordering parts or checking diagrams

Reference: 11016922501 owner's manual

The prefix and full model number determine which diagrams and replacement parts fit (timer, lid switch, drain pump, agitator parts). Even one digit off can point to a different platform.

• Using only the prefix (example: 110) instead of the full model number
• Swapping digits or leaving off the last digits of the model number
• Using a number from the lid, console, or sticker that is not the model label
• Ordering by “looks like mine” instead of matching the model number

Kenmore washers often share similar cabinets and controls across multiple versions; the full model number is what prevents wrong-part returns and repeat repairs.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11016922501, disconnect the hose, clear the blockage, then reinstall it so it is kink-free and has the required air gap. A clogged or incorrectly installed hose can prevent draining and spinning.

• Unplug the washer.
• Turn off both water faucets.
• Keep a shallow pan and towels ready for water in the hose.
• If the washer is full of water, bail out as much as possible before moving it.

1. Pull the washer forward enough to access the back.
2. Remove the drain hose from the standpipe or laundry tub.
3. Check the hooked end and the first 12 to 18 inches for lint, coins, socks, or sludge.
4. Flush the hose with hot water; for buildup, soak the end in hot water mixed with vinegar, then flush again.
5. Reinstall the hose following the routing and clamp placement in the installation guide.

The manual calls out a few installation details that directly affect draining:

• Keep the hooked end; do not straighten it.
• Do not tape or seal the hose to the standpipe; it needs an air gap.
• Do not force extra hose down into the standpipe.
• Rotate the hook to eliminate kinks.
• Make sure the top of the drain hose is at least 39 in. (99 cm) above the floor.

If the hose is clear and the washer still will not drain, the drain pump is the next common suspect. For this model, the replacement is the washer drain pump WP3363394.

A restricted drain path can leave water in the tub, stop the spin cycle, and make the washer seem like it is stuck. Correct hose height and an air gap also prevent dirty water from flowing back into the washer.

Last updated: February 2026

Most Kenmore washers last 10 to 15 years with normal household use and basic maintenance. For Kenmore model 11016922501, good loading habits, correct detergent and bleach use, and fixing small problems early are the biggest factors in reaching the high end of that range (see the owner's manual).

• Overloading and poor load balance: loads should move freely; repeated off-balance spinning strains the drive system.
• Bleach misuse: never pour chlorine bleach directly on clothing; wipe spills promptly.
• Wear items and drive parts: couplers, lid switches, pumps, and clutch components wear over time.
• Water and drain issues: slow fill or slow drain increases cycle stress and can lead to repeat failures.
• Installation basics: leveling and correct drain setup reduce vibration and premature wear (see the installation guide).

• Won’t spin or agitates weakly (common wear points include the washer motor coupling 285753A and agitator dog 80040)
• Won’t drain, or leaves water in the tub (often tied to the washer drain pump WP3363394)
• Lid won’t latch or machine stops mid-cycle (often tied to the washer lid switch assembly WP8318084)
• Loud banging, walking, or chronic off-balance loads (suspension and basket support issues)
• Rust, basket damage, or recurring leaks around the tub area

Knowing the typical 10 to 15 year lifespan helps you decide whether to invest in a repair (like a drain pump or lid switch) versus planning for replacement, especially if multiple major symptoms show up at once.

Last updated: February 2026