Frigidaire GLTF2940EE0 washer Parts

The Frigidaire GLTF2940EE0 is a 27-inch front-load washer with a 3.5 cu. ft. capacity. This is the tub size used to estimate how much laundry the washer can handle per load; it helps you choose proper load size and detergent amount.

Most 3.5 cu. ft. front-load washers handle medium-to-large loads. For best cleaning and spinning performance, we recommend:

• Fill the drum loosely; do not pack items down
• Keep a hand’s width of space at the top of the load
• Wash bulky items (comforters, blankets) one at a time when possible
• Mix large and small items to balance the load
• Use HE detergent and measure carefully to reduce oversudsing

Capacity affects cleaning, rinse quality, and vibration during spin. Overloading can leave detergent residue, cause poor draining or spinning, and increase wear on suspension components.

For model-specific use and care details (cycle guidance, loading tips, and operating notes), use the GLTF2940EE0 owner’s manual.

Last updated: January 2026

Yes. Many Frigidaire Affinity front-load laundry pairs are designed to be stacked using the correct manufacturer stacking kit for the specific washer and dryer models. For your Frigidaire GLTF2940EE0 washer, we recommend confirming the approved stacking method and hardware in the GLTF2940EE0 installation guide before stacking.

Stacking compatibility depends on the exact washer and dryer model numbers, plus the correct stacking kit.

• Verify both model numbers from the rating labels (washer and dryer)
• Check the installation requirements and accessory guidance for your washer
• Use only the stacking kit specified for the Affinity series pair you own
• Confirm the floor is solid and level before stacking
• Keep the power cord and water connections accessible after installation

Most Frigidaire front-load stacking setups require a dedicated stacking kit that locks the dryer to the washer and helps prevent shifting.

Stacking saves space, but it also increases the importance of stability, leveling, and using the correct hardware. A mismatched kit or an unlevel installation can lead to excessive vibration, noise, or movement during spin.

Last updated: January 2026

On the Frigidaire GLTF2940EE0 washer, an E2-style drain error points to a drain problem: the washer is not pumping water out fast enough to continue or finish the cycle. We fix it by checking the drain path (hose and standpipe), then inspecting the drain pump and related wiring.

• Unplug the washer for safety.
• Make sure the drain hose is not kinked, crushed, or pushed too far down into the standpipe.
• Check the standpipe or laundry tub for a slow household drain (a partial clog can mimic a washer failure).
• Run a Drain/Spin cycle after correcting the hose position.
• If the washer stopped mid-cycle, close the dispenser drawer fully; an open drawer can stop operation.

If the hose and household drain are OK, the next most common cause is a weak or jammed pump.

If you need the correct replacement for this model, use the washer drain pump 137221600.

• Verify the washer is getting power (reset a tripped breaker if needed).
• Confirm the drain hose routing and height match the GLTF2940EE0 installation guide.
• Inspect for clogs in the drain hose and at the standpipe.
• Check the pump for debris and listen for abnormal noise.
• If the pump is noisy, seized, or not moving water, replace it.

A drain error can leave water in the tub, prevent high-speed spin, and cause repeated cycle stops. Fixing the drain path first avoids unnecessary part replacement and gets the washer back to finishing cycles normally.

Last updated: January 2026

On a Frigidaire GLTF2940EE0 washer, the F29 error code means the washer is not filling properly (long fill or failure to pressurize). We troubleshoot the water supply path first, then the inlet valve and related wiring; follow the steps in the GLTF2940EE0 owner’s manual.

• Confirm both hot and cold faucets are fully open.
• Make sure inlet hoses are not kinked, crushed, or leaking.
• Remove the hoses and rinse the inlet screen filters at the valve (sediment slows fill).
• Verify the home has normal water pressure and that other faucets flow strongly.
• Power reset: unplug the washer for 2 minutes, then retry a fill cycle.

If the supply and screens are good, the washer may not be opening the valve consistently.

For GLTF2940EE0, the correct fill component to consider is the washer water inlet valve 134371220.

A long fill condition can stop the cycle, leave detergent undissolved, and cause poor rinsing. Fixing the water-in path first prevents unnecessary replacement of higher-cost parts like the control board.

• Use the Frigidaire front load washer error codes guide to confirm the code meaning and see related fill and drain codes.

Last updated: January 2026