Kenmore Elite 66512833K311 dishwasher Parts

To identify your Kenmore Elite dishwasher model number (including model 66512833K311), open the door and look for the model and serial tag on the inner door frame or along the tub opening near the front. We use that exact model number to match the correct parts and instructions in the 66512833K311 owner's manual.

Check these common label locations first:

• Top edge of the tub opening (visible with the door open)
• Left or right inner door frame (door jamb area)
• Side wall of the tub near the front corners
• Inner edge of the door itself (near the latch area)

If the label is worn, use a flashlight and look for lightly printed characters or a stamped metal plate.

Kenmore dishwasher model numbers are typically a long string of numbers and letters. For this page, the correct format is 66512833K311.

• Copy the model number exactly as printed (every digit and letter)
• Include any suffix letters or extra digits (they affect part compatibility)
• Use the model number, not the serial number, when ordering parts

Kenmore dishwashers can look identical across multiple model variations, but parts like the door latch, water inlet valve, or dishrack rollers can differ. Using the exact model number helps ensure you get the right replacement the first time.

Last updated: January 2026

To hard reset the control on your Kenmore Elite dishwasher model 66512833K311, we recommend using the built-in control reset: press CANCEL twice, then reselect your cycle and press START. This clears the current cycle and lets the dishwasher restart cleanly (see the 66512833K311 owner's manual).

Use the method that matches what the dishwasher is doing:

• Stuck cycle or wrong cycle selected: press CANCEL twice to reset the control.
• Need to stop immediately: press CANCEL once; the dishwasher will drain if water is in the tub.
• Start light blinking: close and latch the door, then press START.
• After opening the door mid-cycle: close the door and press START to resume.

1. Open the door slightly to stop spraying; wait for spraying to stop.
2. Open the door fully.
3. Press CANCEL twice.
4. Select the new cycle and options.
5. Close the door.
6. Press START.

These quick checks solve most “won’t start” complaints after a reset:

• Confirm the door is fully closed and latched (an uneven upper rack can prevent closing).
• Make sure a cycle is selected before pressing START.
• Check house power: breaker or fuse.
• Look for items (cookie sheets, cutting boards) blocking the detergent dispenser or wash system.
• If lights other than START blink and it will not run, service is typically needed.

A proper reset clears a paused or confused control state, forces a drain when needed, and prevents restarting a cycle with an empty detergent cup or an unlatched door.

Last updated: January 2026

Yes, repairing a Kenmore Elite dishwasher like model 66512833K311 is usually worth it when the problem is a wear item (rollers, latch, valve, drain pump) and the total repair cost stays well below the price of a replacement dishwasher. It is less cost-effective when multiple major electrical or pump components fail at the same time.

Use this simple rule for most dishwashers:

• Repair it when the fix is a single part and the dishwasher is otherwise cleaning and draining normally.
• Consider replacement when you have repeated leaks, repeated no-drain issues, or multiple expensive parts needed.
• Prioritize safety and installation requirements (proper electrical supply, correct clearances, no carpet install) because a poor install can cause repeat problems.

These are frequent, targeted fixes that usually make sense financially:

• Replace worn rack wheels such as the dishwasher dishrack roller assembly, lower WPW10195417 to stop rack binding and door interference.
• Replace a failing latch such as the dishwasher door latch WPW10653840 if the dishwasher will not start or stops mid-cycle.
• Replace a fill component such as the dishwasher water inlet valve W11175771 if the tub stays dry.
• Replace a drain component such as the dishwasher drain pump WPW10531320 if water remains in the bottom.
• Address drying or heating complaints by testing the heater circuit and, if needed, replacing the heater.

A focused repair keeps a good Kenmore Elite dishwasher running for years and avoids the cost and hassle of replacement. Also, your manual includes model-specific care and troubleshooting steps that can prevent repeat failures.

• Confirm the symptom (no fill, no drain, no heat, won’t start) and when it happens in the cycle.
• Check for simple causes first: clogged filter area, kinked drain hose, or a blocked drain air gap (if your plumbing uses one).
• Review the troubleshooting and maintenance sections in the 66512833K311 owner’s manual to match symptoms to likely causes.

Last updated: January 2026

Common problems on the Kenmore Elite dishwasher model 66512833K311 include not starting (door not fully latched), not draining (drain hose kink or disposer plug not removed), hard-water residue and odors (dirty filters), and poor drying or sanitizing when incoming water is too cool. See the 66512833K311 owner's manual for model-specific troubleshooting steps.

• Dishwasher does not run or Start light blinks: door not closed and latched, rack interference preventing the door from closing
• Water remains in tub or won’t drain: kinked drain hose, food obstruction in drain/disposer, disposer knockout plug still installed, drain pump issue
• Hard-water film, cloudy glasses, spotting: very hard water, not using rinse aid, detergent amount not matched to water hardness, filters need cleaning
• Odors: food soil buildup, filters not cleaned monthly, dishwasher not used daily
• Not drying or “did not sanitize”: rinse aid missing, cycle interrupted, water heater set below 120°F (49°C)

1. Close the door firmly; if the Start light is blinking, close the door and press START.
2. Make sure the upper rack is level; an uneven rack can keep the door from latching.
3. Confirm the cycle fully completed (status light behavior varies by cycle).
4. If connected to a disposer, confirm the disposer inlet knockout plug was removed.
5. Check the drain hose routing for kinks and verify the high loop/air gap setup per the 66512833K311 installation guide.

Most “common problems” trace back to airflow and water flow basics: a door that is not fully latched stops the cycle, restricted draining leaves dirty water behind, and hard water plus dirty filters quickly causes residue, odors, and weak cleaning.

Last updated: January 2026