Owner’s manual
Can I scrap a chainsaw?
Yes. We recommend scrapping a Craftsman 358360380 gas chainsaw by separating recyclable metal from fuel and oil residues first; most metal components (bar, chain, engine housings) can go with scrap metal once the saw is fully drained and safe to handle.
How to prep a chainsaw for scrapping
- Let the engine cool completely before handling.
- Drain the fuel tank and bar oil tank into approved containers.
- Wipe up any spills and keep the work area away from sparks or flames.
- Remove the guide bar and chain so the unit is safer to transport.
- Bag small loose hardware (nuts, screws) so it does not get lost.
- Store and transport the saw with the bar covered (scabbard) if the bar is still installed.
What typically gets recycled vs. disposed
| Item | What to do | Notes |
|---|---|---|
| Guide bar and chain | Scrap metal | Sharp edges; handle with gloves. |
| Engine and metal housings | Scrap metal | Drain fluids first. |
| Plastic covers/handles | Varies by recycler | Some accept mixed materials, many do not. |
| Fuel, 2-cycle mix, bar oil | Household hazardous waste | Never pour into drains or onto soil. |
Safety and handling reminders (from the manual)
The 358360380 manual emphasizes fuel safety and general handling: mix/pour fuel outdoors, wipe spills, move away from fueling area before starting, and keep ignition sources away from fuel vapors. For scrapping, the same rules apply while draining and transporting. See the 358360380 owner's manual.
Why it matters
Scrapping a chainsaw is mostly about preventing fire risk and environmental contamination. Draining fuel and bar oil first also helps your recycler accept the saw and keeps your vehicle and workspace cleaner.
Last updated: January 2026
Is 40 1 or 50 1 better for chainsaws?
For the Craftsman 358360380 gas chainsaw, 40:1 is the better choice because it is the manufacturer-specified fuel mix. Mix 3.2 oz of quality synthetic 2-cycle (air-cooled) oil per 1 gallon of unleaded gas; using 50:1 reduces lubrication compared to what this engine is designed to run. See the 358360380 owner's manual for the exact fueling instructions.
Recommended mix for this model
Use the ratio the engine was designed for; it protects the piston, rings, and crankshaft bearings under load.
- Mix 40:1 (gasoline:oil) for Craftsman 358360380
- Use unleaded gasoline
- Use synthetic 2-cycle air-cooled engine oil (not automotive or marine oil)
- Shake the fuel container after mixing to fully blend the oil
- Make fresh mix and avoid storing mixed fuel for long periods
Quick mix chart
| Fuel mix ratio | Oil per 1 gallon gas | What it means for the saw |
|---|---|---|
| 40:1 | 3.2 oz | Correct lubrication level for Craftsman 358360380 |
| 50:1 | 2.6 oz | Less oil than specified; increases wear risk |
Why it matters
Two-stroke chainsaws rely on the oil in the fuel for lubrication and cooling. Running leaner on oil than specified (like 50:1 in a 40:1 engine) can accelerate wear, raise operating temperatures, and shorten engine life.
If you are troubleshooting running issues
If the saw smokes heavily, loads up, or runs rough, the cause is usually fuel quality, incorrect oil type, or carburetor tuning, not the fact that 40:1 is “too much oil.” Use these checks:
- Confirm you measured 3.2 oz oil per gallon accurately
- Confirm the oil is 2-cycle air-cooled synthetic
- Drain old fuel and refill with fresh 40:1 mix
- Check and clean the air filter if performance is poor
- Review safe starting and operating practices in the 358360380 owner's manual
Last updated: January 2026
What model number is a Craftsman 16 36cc chainsaw?
The model number for a Craftsman 16-inch, 36cc chainsaw depends on the exact unit; Craftsman made multiple 16-inch saws in the 36cc range. On this model page, the correct model number is 358360380, and the manual identifies it as an 18-inch bar, 42cc (2.6 cu. in.) saw.
How to find the model number on your Craftsman chainsaw
Use the model tag on the saw, not the bar length alone.
- Check the housing near the starter/recoil cover
- Look around the rear handle area
- Check near the fuel tank or oil tank
- Write the full number exactly as shown (including any dots)
- Match that number when ordering a chain, bar, clutch, or fuel system part
For model-specific identification details and specs, use the 358360380 owner’s manual.
Quick comparison: 16-inch 36cc vs this model (358360380)
If your saw is truly a 16-inch 36cc, it is a different model than 358360380.
| Item | 16-inch 36cc chainsaw | Craftsman 358360380 |
|---|---|---|
| Bar length | 16 in. | 18 in. |
| Engine size | 36cc | 42cc (2.6 cu. in.) |
| Engine type | 2-cycle | 2-cycle |
Why it matters
Parts fit is tied to the exact model number. A similar-looking Craftsman chainsaw can use a different chain drive link count, different bar mount, or different fuel line routing.
If you are servicing fuel delivery on model 358360380
These are common fuel-related replacement parts for 358360380:
- Ayp lawn & garden equipment fuel line, large 530069216 (fuel line from tank to carburetor)
- Fuel tank cap 580940901 (seals the fuel tank)
- Ayp chainsaw fuel line fitting 530023877 (fuel line connector/fitting)
Last updated: January 2026
Where is the model number on a chainsaw?
On the Craftsman chainsaw model 358360380, the model number is typically printed on the product identification label or ID tag on the saw body. Check the areas around the rear handle, starter housing, or near the fuel and oil caps; these are common label locations.
Where to look on the saw
We recommend checking these spots first (wipe off oil and sawdust so the label is readable):
- Near the rear handle and trigger area
- On the starter/recoil housing (pull-start side)
- Around the fuel tank area, including near the fuel cap
- Around the bar mount/clutch cover area
- On the bottom of the saw body (underside of the fuel tank)
What the label may show
On many Craftsman chainsaws, the ID label includes more than just the model number. You may see:
- Model number (for this saw: 358360380)
- Bar length (the manual cover references an 18-in bar)
- Engine size (the manual cover references 42cc, 2-cycle)
- Serial number (useful for parts lookups)
| If you find this | Use it for |
|---|---|
| Model number | Matching parts diagrams and common parts like fuel line, air filter, clutch |
| Serial number | Narrowing down production variations when ordering parts |
| Bar length | Choosing the correct bar and chain size |
Why it matters
Using the exact model number helps us match the correct parts and diagrams for your saw, especially for fuel system and ignition components where small variations can affect fit.
For model-specific identification details and the exact model formatting shown by Craftsman, use the 358360380 owner’s manual.
Last updated: January 2026
