Kenmore 66513834K601 dishwasher Parts

Yes. Your Kenmore 66513834K601 dishwasher uses a built-in filtration system inside the wash module that intermittently filters soil from the wash water, so you do not need to pre-rinse dishes. For cleaning and care details, follow the steps in the owner's manual.

This model is part of the ULTRA WASH soil removal system, which includes a triple action filtration system and an optical soil sensor (turbidity sensor) that helps adjust the cycle based on how dirty the water is.

Common signs the filter area needs attention:

• Grit or food particles left on dishes after a cycle
• Grinding or crunching noises (often from hard debris in the wash module)
• Cloudy glasses or film buildup
• Poor wash performance on the top rack
• Odors that return quickly after cleaning

Most Kenmore dishwashers with this style of filtration clean up quickly with basic maintenance.

• Turn off power at the breaker before reaching into the sump area
• Remove the lower rack for access
• Lift out any visible debris near the sump and lower spray arm
• Rinse filter screens and covers under running water (no wire brushes)
• Reinstall parts fully seated so the spray arms do not hit anything

If your dishwasher is not draining well, also check the drain path and follow the cleaning guidance in the how to clean and maintain your dishwasher article.

A clean filter area helps your circulation pump move water at full pressure, improves cleaning on both racks, and reduces redepositing soil onto dishes. It also helps prevent drain issues that can mimic a pump or hose problem.

Last updated: February 2026

On Kenmore dishwasher model 66513834K601, an F2 E2 code is typically cleared by canceling the current cycle and restarting the control. Press CANCEL/DRAIN to run the drain (about 2 minutes if needed), then select a new cycle and press START/RESUME. For model-specific button sequences, use the owner's manual.

• Press CANCEL/DRAIN once; keep the door closed so the unit can drain.
• Wait about 2 minutes for the Cancel/Drain light to turn off.
• Confirm the door is fully closed and latched.
• Select your desired cycle and options.
• Press START/RESUME to begin.
• If START/RESUME is flashing, press START/RESUME again to resume after a door-open or power interruption.

F2 E2 is commonly associated with a user interface (keypad) communication or button input problem. If the code returns right away after the reset, focus on basic control checks first.

• Turn off power at the breaker for 1 minute, then restore power and try again.
• Check the control panel for a stuck or wet key; dry it and try a reset.
• If the dishwasher will not respond or behaves erratically, a control component may be involved; on this model, the dishwasher electronic control board WPW10084142 is one of the control parts used in the circuit.

Resetting correctly clears the active cycle and drains water so the dishwasher can restart cleanly. If F2 E2 repeats, it helps narrow the problem to the user interface/control system instead of wash components like the pump or heating circuit.

Last updated: February 2026

On Kenmore dishwasher model 66513834K601, the F4E1 service code points to a wash motor or pump motor problem (the dishwasher is not circulating water correctly). After repairing the cause, clear the code by running the reset sequence described in your owner's manual.

F4E1 is tied to the dishwasher’s ability to move water through the spray arms. In most cases, the issue is in the circulation system.

Common causes include:

• A failing circulation/wash motor
• A jammed impeller or debris in the sump area
• A wiring or connection problem to the motor
• A control not powering the motor correctly
• A motor that overheated and needs time to reset

Turn off power at the breaker before inspecting internal components.

• Confirm the door is fully closed and latched
• Verify the cycle is set correctly, then press Start/Resume
• Check for standing water and clear any obvious blockage
• Listen for the motor trying to run (humming) versus silence
• If the unit stopped mid-cycle, allow a few minutes for an overload reset, then try again

If the dishwasher is not operating properly, the troubleshooting steps in the owner's manual are the best place to start.

Many Kenmore 665-series dishwashers clear stored faults with a keypad sequence.

Typical reset method:

• Press any 3 keys in order 1-2-3
• Repeat three times: 1-2-3, 1-2-3, 1-2-3
• Then start a short cycle to confirm normal operation

Keypads vary by console layout, so use the exact sequence listed for your control in the owner's manual.

If diagnostics point to circulation, these model-matched parts are often involved:

When the wash motor cannot circulate water, dishes stay dirty and the dishwasher may stop mid-cycle or trigger additional faults. Fixing the circulation issue restores spray pressure, cleaning performance, and normal cycle timing.

Last updated: February 2026