Whirlpool WTW5105HC0 washer Parts

Whirlpool washer parts are not universally interchangeable, even between models that look similar. For Whirlpool WTW5105HC0, we recommend replacing parts with the exact part ID listed for your model to ensure proper fit, correct operation (spin, agitation, lid locking), and to prevent repeat failures.

Parts can share a similar shape or function, but Whirlpool often changes:

• Electrical connectors and wiring pinouts (actuators, valves, controls)
• Mounting points and pulley or belt geometry
• Software calibration requirements (control and drive system)
• Hose routing and clamp styles
• Safety components (lid lock and lid strike alignment)

The safest approach is to confirm compatibility using the model-specific diagrams and procedures in the WTW5105HC0 owner's manual.

These parts are frequently model-specific and should be matched by part ID:

• Washer actuator W10913953 (controls shifting between agitate and spin)
• Washer water inlet valve W11165546 (fill performance and connector style)
• Lid lock-sol W11700916 and washer lid strike W11457841 (must align to lock and start)
• Drive belt W11239857 and Whirlpool washer drive pulley W10721967 (must match the drive system)

Use this checklist to avoid ordering the wrong replacement:

• Match the model number exactly: WTW5105HC0
• Match the part ID (not just a similar-looking part)
• Compare connector count and plug shape on electrical parts
• Confirm the symptom points to that part (fill, drain, spin, lock)
• Follow the install and safety steps in the WTW5105HC0 owner's manual

Using the correct Whirlpool WTW5105HC0 part prevents fitment problems and protects key functions like water filling, lid locking, and the belt-drive system. It also reduces the chance of damaging related components such as the drive motor or main control.

Last updated: February 2026

On the Whirlpool WTW5105HC0 washer, the F05 E01 (often shown as F5E1) error points to a lid lock or lid switch problem. The washer is sensing the lid is unlocked when it should be locked, so it stops the cycle for safety.

• Unplug the washer (or turn off the breaker) for 5 minutes, then restore power.
• Open and close the lid firmly; do not slam it.
• Remove anything that could keep the lid from closing flat (overhanging laundry, detergent cup, etc.).
• Check the lid strike for cracks, looseness, or misalignment.
• If the code returns, run a short cycle with an empty basket to confirm it is repeatable.

For model-specific operating and safety details, follow the steps in the WTW5105HC0 owner's manual.

If the lid is closing normally but the code keeps coming back, these parts are the most common fixes:

Model-matched parts for WTW5105HC0:

• Lid lock-sol W11700916
• Washer lid strike W11457841

The lid lock system is a safety interlock. If the control does not see a reliable “lid locked” signal, it prevents spinning to reduce the risk of injury and water slosh.

• Verify the washer is level; excessive vibration can cause intermittent lid lock sensing (leveling guidance is in the manual).
• If the lid lock and strike look good, wiring or the control could be involved; at that point, a service diagnosis is the fastest path.

Last updated: February 2026

The most common Whirlpool washer complaint is a no-start condition: the control lights come on, but the cycle will not begin. On the Whirlpool WTW5105HC0, this is often tied to lid-lock sensing, control input issues, or a cycle that was interrupted and not restarted correctly (see the WTW5105HC0 owner's manual).

• Make sure the lid is fully closed and you hear/feel it latch.
• Press POWER, reselect the cycle, then press START (avoid rapid button presses).
• Unplug the washer for 2 minutes, then plug it back in to reset the control.
• Confirm the outlet is a grounded 3-prong outlet; do not use an extension cord.
• If the cycle was interrupted, restart properly (some cycles require a full reset).

If the washer has power but will not start, these model-matched parts are common suspects:

• Lid lock-sol W11700916 (lid must lock for the washer to run)
• Washer lid strike W11457841 (if broken or misaligned, the lid may not register as closed)
• Washer actuator W10913953 (can affect shifting and cycle progression)

A washer that will not start is usually a safety or sensing block (especially lid-lock related). Fixing the root cause prevents repeated interruptions, incomplete draining/spinning, and unnecessary wear on the drive system.

Last updated: February 2026