Kenmore 11027132411 washer Parts

The Kenmore washer model 11027132411 is a top-loading high efficiency, low-water washer; its exact tub capacity in cubic feet is listed in the product specifications section of the 11027132411 owner's manual.

In the manual, look for a section labeled Specifications, Capacity, or Model information. If you are comparing washers for fit or load size, use the capacity value from the manual rather than estimating from the “110” prefix.

Typical places to check:

• The first few pages (model identification and features)
• A specifications page near the back
• Any “cycle guide” notes that reference load size
• The model and serial tag on the cabinet (helps confirm you are reading the right manual)

This model family is a modern HE top-load design (low-water, impeller-style wash system). Most washers in this category commonly fall into a mid-size capacity range.

Capacity affects how full you can load the basket, how well items circulate, and how long cycles may take. Using the correct capacity also helps you choose the right HE detergent amount and avoid out-of-balance spinning.

If the washer seems to “hold less” than expected, the issue is often loading technique or a washplate/drive problem rather than true capacity.

• A worn or loose washplate can reduce turnover and cleaning performance: impeller W10752285
• Drive issues can affect agitation and spin, making loads seem “too heavy”: drive assembly W11393685
• Suspension problems can limit spin performance with larger loads: damper assembly W11130359

Last updated: February 2026

Your Kenmore washer model number is printed on the appliance’s model and serial tag. For Kenmore model 11027132411, check under the lid around the opening first; if you do not see it there, check the back panel near the power cord or control area. Use the full model number to match exact parts and instructions.

Most Kenmore top-load washers like 11027132411 place the tag in one of these spots:

• Under the lid, around the tub opening or underside of the lid
• On the rear of the cabinet (upper left or upper right)
• Along the back edge of the control console area
• Occasionally on the inside edge of the cabinet frame

For diagrams and model identification details, use the 11027132411 owner’s manual.

Kenmore washer model numbers commonly start with 110 and include a longer string of digits. Entering the complete model number helps us match the correct Kenmore washer parts list, including items like the lid lock, drain pump, and water valve.

• Write the model number exactly as shown (all digits, no spaces)
• Do not use the lid style or color to identify the model
• If multiple numbers appear, use the one labeled MODEL
• Match parts by model number first, then confirm by part description

Kenmore washers share similar looks across many series, but internal components can differ. Using the correct model number prevents ordering the wrong part and helps troubleshooting steps in the manual line up with your washer’s controls and features.

Last updated: February 2026

To reset your Kenmore 11027132411 washer, we reset power to fully reboot the control: unplug the washer (or switch the breaker off) for 5 minutes, then restore power and start a cycle. This clears many control glitches and communication errors.

• Press Start/Pause/Unlock Lid once to pause the cycle.
• Unplug the washer (or turn the breaker off).
• Wait 5 minutes so the control fully powers down.
• Plug back in (or turn breaker on).
• Select a cycle and touch and hold Start/Pause/Unlock Lid for up to 3 seconds to start.

For normal operation details and button behavior, follow the 11027132411 owner's manual.

Many F-type codes clear and restart with the Start/Pause/Unlock Lid button.

• Touch Start/Pause/Unlock Lid once to clear the code.
• Touch and hold Start/Pause/Unlock Lid again (up to 3 seconds) to restart.
• If the code returns quickly, reset power for 5 minutes again.

If the washer will not start after a reset, focus on the most common “no-run” causes:

• Confirm the lid is fully closed and latching; a failed lock can stop the cycle.
• Check the outlet and breaker; avoid extension cords.
• Reduce oversudsing (use HE detergent and the correct amount).
• Rebalance or reduce a tightly packed load.

If the lid will not lock or unlock consistently, the washer lid lock assembly W10810403 is the model-matched part to check.

A proper power reset clears temporary control faults without changing cycle settings or requiring disassembly; it is the fastest first step before deeper troubleshooting or parts replacement.

Last updated: February 2026

To unclog the drain hose on your Kenmore washer model 11027132411, we disconnect the hose, remove the blockage, then reinstall it to the correct standpipe depth and height so the washer drains quickly and avoids long-drain problems. Use the setup details in the installation guide.

• Unplug the washer.
• Turn off both water faucets.
• Keep towels and a shallow pan ready for water.
• Let hot wash water cool before handling hoses.

• Pull the washer forward for access.
• Remove the hose from the standpipe or laundry tub.
• Check the hose end for lint, coins, socks, or sludge; remove debris by hand.
• Flush with hot water; for buildup, soak the hose end in hot water plus vinegar for 20 to 30 minutes, then flush again.
• For stubborn clogs, use a flexible brush or plastic zip tie (avoid sharp tools).

Use these installation targets from the installation guide:

• Do not force excess hose into the standpipe.
• Do not lay the hose on the bottom of a laundry tub.
• Use the drain hose form and secure the hose to the standpipe or tub.

Replace the hose if it is kinked, soft, split, or still restricted after cleaning. The correct replacement for this model is the washer drain hose W11244231.

A partially clogged or incorrectly installed drain hose makes the drain pump work harder, increases cycle time, and can trigger long-drain conditions.

Last updated: February 2026

A Kenmore washer typically lasts 10 to 12 years with normal household use and routine care. For your Kenmore top-load high-efficiency washer model 11027132411, following the maintenance and operating guidance in the 11027132411 owner's manual helps you get the longest service life.

• Load size and balance: frequent overloading and off-balance loads increase wear on the suspension and drive system.
• Detergent choice: this model is designed for HE (high efficiency) detergent; using the right type helps prevent residue and performance issues.
• Water quality: hard water can contribute to buildup that affects valves and wash performance.
• Drain performance: slow draining strains the pump and can leave water in the tub.
• Vibration and leveling: an unlevel washer shortens the life of dampers, springs, and bearings.

• Lid will not lock or unlock: check the washer lid lock assembly W10810403.
• Won’t drain or drains slowly: inspect the washer drain pump W10876600 and drain hose routing.
• Loud banging or excessive shaking: suspension components such as the damper assembly W11130359 often wear first.
• Weak agitation or poor spin: drive and clutch-related parts can be involved.

Knowing the expected 10 to 12 year lifespan helps you decide whether to repair (often best for a single failed part like a lid lock or drain pump) or plan a replacement when multiple major systems start failing.

Last updated: February 2026