Kenmore 79046599504 electric range Parts

To replace the oven control board on your Kenmore electric range model 79046599504, we shut off power, access the control area, move each wire to the matching terminal on the new board, reconnect the ribbon cable, then reassemble and test Bake and Broil functions per the 79046599504 owner's manual.

Safety first (do this every time)

• Turn off the range breaker (240V) and confirm the display is dark.
• Let the oven cool completely before working near the control panel.
• Avoid touching bare terminals; a range can store hazardous voltage.
• Keep screws and spacers organized so the control panel seats correctly.
• If wiring insulation looks overheated, stop and replace damaged wiring before powering up.

Replacement steps (control board and wiring)

1. Disconnect power at the breaker.
2. Access the control area (typically from the back panel or control panel area, depending on configuration). Use the 79046599504 installation guide for safe access and reassembly practices.
3. Label wires (masking tape works) and take a photo before removing anything.
4. Transfer wires one at a time from the old board to the same terminal on the new board.
5. Reconnect the ribbon cable: fully insert it into the connector, then lock/snap the connector into place.
6. Reinstall panels, restore power, and run a quick functional check.

Quick functional check after installation

Function	What to verify	What it suggests if it fails
Bake at 350°F	Oven begins heating and holds temp	Sensor, element, or wiring issue
Broil	Top element heats	Broil circuit or element issue
Clock/timer	Keys respond normally	Overlay/control issue

If the oven still will not heat

These are common related checks on 79046599504 after a control replacement:

• Confirm the ribbon cable is straight and fully seated.
• Check for loose spade terminals or a pinched harness behind the panel.
• If temperature is erratic, test/replace the frigidaire range oven temperature sensor 316217002.
• If Bake does not heat, inspect/replace the frigidaire range bake element 318255401.
• If you see heat damage at the power connection, inspect the terminal block 5304409888.

Why it matters

The oven control board coordinates temperature sensing, element cycling, and keypad inputs. A single miswired terminal or an unlocked ribbon connector can prevent heating, cause error codes, or make the keypad unresponsive.

Last updated: February 2026

On the Kenmore 79046599504 electric range, an oven that “stops working” is usually caused by a power supply problem (tripped breaker or loose connection), a failed heating component (bake or broil element), or a control/sensing issue such as a bad temperature sensor or control board. Use the checks below to pinpoint the failure.

Quick checks we recommend first

• Confirm the range has power; reset the double breaker fully OFF, then ON.
• Make sure the oven is not set to a delayed start or control lock (see the 79046599504 owner's manual).
• If the oven was in a power outage, turn the oven OFF; the manual warns the oven can restart when power returns.
• Verify the oven vent is not blocked; blocked venting can cause poor performance and overheating.
• If the cooktop works but the oven does not, focus on oven heating parts and controls.

What to look for in bake, broil, and clean modes

Your installation checks describe what “normal” looks like:

Mode	What should happen	What it suggests if it does not happen
Bake at 350°F	Lower element should glow red	Failed bake element, wiring issue, or control problem
Broil	Upper element should glow red	Failed broil element, wiring issue, or control problem
Self-clean preheat	Upper element should glow red	Element or control issue

If bake will not heat, a common repair is replacing the bake element, such as the frigidaire range bake element 318255401 when it matches your model’s parts list.

Sensor and control causes

If elements look intact but temperatures are erratic or the oven will not regulate heat, the oven temperature sensor is a prime suspect. For this model’s parts list, see the frigidaire range oven temperature sensor 316217002.

Why it matters

An oven that is not heating correctly can lead to undercooked food, long preheat times, and overheating of wiring or controls. Checking for proper element operation in BAKE and BROIL quickly separates a simple part failure from a control or power issue.

Last updated: February 2026

On the Kenmore electric range model 79046599504, the model and serial number are printed on the serial plate on the oven front frame, typically behind the oven door. On some versions, the serial plate is behind the storage drawer instead (pull the drawer out to look).

Where to look first (fastest checks)

• Open the oven door and look along the front frame (the face of the oven opening).
• Check the left and right sides of the front frame for a rating plate sticker.
• If you do not see it, pull out the storage drawer and look on the frame behind it.
• Write down the model number, serial number, and any lot number/letter shown.
• Use the exact model number when ordering parts to avoid mismatches.

What the label usually looks like

Most Kenmore ranges use a small rating plate that includes the model and serial number together.

Label detail	What it’s used for
Model number (example: 79046599504)	Identifies the exact range configuration
Serial number	Helps match production run details
Lot number/letter (if shown)	Helps narrow down compatible parts

Why it matters

Kenmore ranges can look similar across multiple 790-series models, but parts like a bake element, control panel, or temperature sensor can vary by revision. Using the serial plate information helps us match the correct replacement parts and diagrams.

Helpful reference

For the exact serial plate location illustrations and parts-ordering notes, use the 79046599504 installation guide.

Last updated: February 2026

If your Kenmore electric range model 79046599504 is not heating, the most common causes are a failed bake or broil element, a bad oven temperature sensor, or a control problem. Start with safe power checks, then test heating components for visible damage and continuity.

Quick checks first (no tools)

• Confirm the range has power; a tripped breaker can leave the oven with partial power.
• Make sure all controls are set correctly and not left in OFF after a power event.
• If the issue started after moving or installing the range, recheck the power connection steps in the installation guide.
• Avoid touching heating elements; they can stay hot long after use.
• If the oven was lined with foil, remove it; foil can disrupt heat and damage the oven interior.

Most likely failed parts on model 79046599504

Electric ovens typically heat with a bake element (most baking) and a broil element (top heat). If either is open (no continuity), the oven may not heat or may heat very poorly.

Symptom	Most likely cause	What we do next
No heat in Bake, Broil works	Bake element failed	Inspect and test the frigidaire range bake element 318255401
No heat in Broil, Bake works	Broil element failed	Inspect broil element for blisters or breaks
Oven heats but temps are wrong	Sensor out of range	Test/replace the frigidaire range oven temperature sensor 316217002
Surface burners work, oven dead	Control or wiring issue	Check wiring connections; follow diagnostics in the owner's manual

What to test with a multimeter (power off)

• Bake element and broil element: check for continuity; replace if open.
• Oven temperature sensor: if the sensor is out of spec, the control may prevent proper heating.
• Wiring/connectors: look for burned terminals or loose connections, especially after a move.

Why it matters

A no-heat condition is usually a simple heating-circuit failure (element or sensor). Catching it early prevents repeated overheating attempts that can stress wiring, terminals, and the control.

Last updated: February 2026