Kenmore Elite 79691472210 dryer Parts

On the Kenmore Elite dryer model 79691472210, the model number is printed on the rating label. You will usually find that label on the door opening (cabinet frame) when you open the dryer door, or on the back of the dryer near the top.

• Open the dryer door and look along the cabinet frame around the door opening
• Check the inside edge of the door itself (some units place the label here)
• Look on the back panel near the top corner
• If the dryer is stacked, check the door opening first so you do not have to unstack it

The label typically includes the model number, serial number, and electrical or gas information. For the quickest match:

• Look for a long number string like 79691472210
• Wipe dust off the label with a dry cloth so the print is readable
• Take a photo of the label before ordering parts

On Kenmore Elite dryers, the label location is usually the same for electric and gas models, but the label details differ.

We use the exact model number to match the correct parts and diagrams for your dryer. Even small model number differences can change items like the drum belt, idler pulley, or thermostats.

For model-specific identification details and diagrams, use the 79691472210 owner’s manual.

Last updated: January 2026

To hard reset your Kenmore Elite dryer model 79691472210, unplug the power cord (or switch the breaker off) for 1 to 5 minutes, then restore power and try a normal cycle. This clears many control glitches, but it will not fix airflow or failed safety parts.

• Turn the dryer OFF.
• Unplug the dryer from the outlet (or turn the circuit breaker OFF).
• Wait 1 to 5 minutes.
• Restore power.
• Close the door firmly, then press Power and start a cycle.
• If the panel is unresponsive, repeat the reset once after a full 5 minutes.

A “reset” often seems to work only when the underlying issue is intermittent. If the dryer still will not start or stops quickly, check these common causes:

• Door not fully closed or a failed door switch (consider dryer door switch EBF61496102)
• Restricted venting or lint buildup causing overheating and shutdown
• Drive system problem (broken belt or seized drum support)
• Moisture sensor issues causing odd auto-dry behavior
• Household power issue (tripped breaker, loose cord connection)

A hard reset clears the control board’s temporary state, but dryers commonly stop for safety reasons (overheating, door circuit problems, or a failed drive component). Fixing the root cause prevents repeat shutdowns and protects the heater and motor.

For model-specific control behavior and operating steps, follow the 79691472210 owner's manual.

Last updated: January 2026

On the Kenmore Elite dryer model 79691472210, CL means the controls are locked (Control Lock/Child Lock). The dryer may still run some functions, but most buttons will not respond until you unlock the controls using the procedure in the 79691472210 owner's manual.

• CL shows on the display (often alternating with time remaining)
• Most buttons do nothing when pressed
• The cycle may continue running, but you cannot change settings
• The door may open, but starting a new cycle can be blocked
• Some indicator lights may stay on while locked

Use the exact unlock method listed for your control panel in the 79691472210 owner's manual. On many Kenmore Elite dryers, unlocking is done by pressing and holding a specific button (or button combination) for about 3 seconds until CL disappears.

• Press and hold the correct lock button long enough (a quick tap usually will not work).
• Make sure the dryer is powered on (some models only unlock when powered).
• If the display is unresponsive, unplug the dryer for 1 minute, plug it back in, then try again.

Control Lock prevents accidental changes to cycle settings, which helps avoid interrupted drying, unexpected temperature changes, and unintended starts, especially in homes with kids.

If you’re seeing an actual error code (not just CL), use Kenmore elite dryer error codes to match the code to the most likely cause.

Last updated: January 2026

The Kenmore Elite 79691472210 dryer is a full-size 27-inch class dryer. Most units in this class measure about 27 inches wide, 38 to 44 inches tall, and 27 to 31 inches deep (depth varies most with door style and venting clearance). For the exact cabinet dimensions for your unit, use the 79691472210 owner’s manual.

When you are measuring for a laundry closet, pedestal, or stacking space, we recommend allowing room for the dryer plus airflow and venting.

• Width: typically ~27 inches
• Height: typically ~38 to 44 inches
• Depth: typically ~27 to 31 inches
• Rear clearance: typically 4 to 6 inches for venting and cord/gas line routing
• Side clearance: typically 1 inch or more for vibration and airflow

Use a tape measure and record the largest measurement in each direction.

• Measure width at the widest point of the cabinet (not the control panel overhang unless it sticks out).
• Measure height from the floor to the top of the cabinet (include leveling feet if extended).
• Measure depth from the back panel to the front-most point (often the door or handle).
• Add space for the vent elbow and the power cord (or gas connector on gas models).

Correct sizing prevents crushed venting (long dry times), pinched cords or gas lines, and door clearance problems. It also helps avoid vibration noise caused by tight side clearances.

If you are also troubleshooting noise or thumping after moving the dryer, inspect wear items like the dryer drum belt 4400EL2001F and drum support components.

Last updated: January 2026