Maytag MTW5620TQ2 washer Parts

The Maytag MTW5620TQ2 top-load washer has a 3.2 cu. ft. capacity. This is the tub volume the washer is designed around, and it helps you choose appropriate load sizes and cycles for best cleaning and spin performance. See the owner's manual for load-size guidance and cycle details.

A 3.2 cu. ft. top-load washer is a mid-capacity design that handles typical household laundry well when loads are not overpacked.

• Wash bulky items one at a time (for example, a comforter or thick blanket)
• Keep mixed loads loosely packed so water and detergent can circulate
• Balance items (towels with towels, jeans with similar items) to reduce vibration
• Avoid compressing clothes down into the basket
• Use the cycle and water level intended for the fabric type

Capacity affects cleaning and reliability. Overloading a top-load washer commonly leads to poor agitation, out-of-balance spinning, and extra noise. The manual’s troubleshooting guidance also emphasizes keeping loads balanced and the washer level to prevent vibration and noisy operation.

Last updated: February 2026

For the Maytag MTW5620TQ2 washer, the most common day-to-day complaint is the washer not draining or not spinning. In our experience, the fastest things to check are lid-closed operation, drain hose setup, and oversudsing; all three are called out in the owner's manual.

• Won't spin or agitate: lid not fully closed or a failing lid switch
• Won't drain or drains slowly: kinked/clogged drain hose, pump restriction, or pump failure
• Cycle seems stuck filling or draining: drain hose positioned too low or sealed too tightly in the standpipe
• Excessive suds: too much detergent (especially with soft water)
• Noisy or shaking: unbalanced load or washer not level

1. Close the lid firmly; this model will not agitate or spin with the lid open.
2. Check the drain hose height; the end of the drain hose should not be more than 96 in. (244 cm) above the floor.
3. Prevent siphoning; the top of the drain hose must be higher than the washer water level, and the hose should not be taped airtight to the standpipe.
4. Reduce suds; measure detergent carefully and use less if you have very soft water.
5. Balance the load and level the washer; an unbalanced load can cause noise and poor spinning.

If the basic checks above do not solve it, these are common repair paths for MTW5620TQ2:

Drain, spin, and lid-sensing problems can look like a “dead washer,” but they are often caused by a simple installation issue (drain hose height or siphoning) or a single failed component (lid switch or drain pump). Fixing the root cause prevents repeat clogs, oversudsing, and water leaks.

Last updated: February 2026

We do not recommend bypassing the lid lock or lid switch on your Maytag MTW5620TQ2 washer. The lid must be closed for the washer to agitate or spin, and defeating that safety feature increases the risk of injury and damage. Use the troubleshooting steps in the owner's manual instead.

• Make sure the lid is fully closed and not being held up by an oversized item.
• Unplug the washer for 1 minute, then plug it back in to reset the cycle.
• Confirm the washer is not in a normal pause (some cycles pause briefly).
• Reduce the load size; overloading can prevent proper operation.
• Check your outlet and breaker; a power issue can mimic a lid lock problem.

On MTW5620TQ2, the washer is designed not to agitate or spin with the lid open. If the lid is closed but the washer still will not run, the lid switch circuit is a common failure point.

Common symptom patterns

• The lid lock/switch prevents reaching into a moving tub or agitator.
• Bypassing can lead to injury if the basket starts spinning unexpectedly.
• It can also create new electrical or control problems that increase repair cost.

If you are diagnosing a no-spin/no-agitate condition on this model, these are the most common related parts to check:

• Washer lid switch assembly WP8318084 (most common for lid-sensing failures)
• Clutch 285785 (if the motor runs but the basket does not spin)
• Washer drive motor WP661600 (if the washer is completely dead or motor will not run)

Last updated: February 2026

Yes; you can wash a king size comforter in your Maytag MTW5620TQ2 washer if it fits loosely in the basket and can move freely during agitation. If it has to be packed down, it will not clean or spin safely; use a larger-capacity machine.

Use these quick checks before starting:

• The comforter sits below the top of the basket and does not press hard on the lid.
• You can slide an open hand between the comforter and the basket wall in a few spots.
• The load shifts easily when you reposition it; it does not feel wedged.
• The washer can agitate normally; no stalling or struggling.
• The load stays balanced in spin; no repeated banging or walking.

Follow cycle and load-size guidance in the MTW5620TQ2 owner's manual. In general, bulky items wash best with plenty of water and room to circulate.

• Choose a bulky/bedding cycle if your control has one.
• Set the correct load size or water level for the item.
• Use the warmest water allowed by the care label.
• Use a small amount of HE detergent to prevent trapped suds.
• Add an extra rinse if the comforter feels soapy.

Stop the cycle and correct the load; repeated off-balance spinning strains the drive and suspension.

Bulky bedding that is too tight in the basket cannot circulate for proper cleaning and can trigger severe out-of-balance spinning.

Last updated: February 2026