Kenmore 10658142801 refrigerator Parts

On Kenmore side-by-side refrigerator model 10658142801, the water filter is located in the base grille below the freezer compartment door. You access it from the front by pressing the eject button and pulling the filter straight out; the base grille does not need to be removed (see the owner's manual).

How to find it quickly

• Open both refrigerator doors so you can see the full base grille area.
• Look at the base grille directly under the freezer door.
• Find the eject button next to the filter cap.
• Press the eject button.
• Pull the filter straight out by the cap.
• Expect a small amount of water to spill from the old filter.

What you will see (parts and labels)

What you see	What it does	Notes
Eject button	Releases the filter	Press, then pull straight out
Filter cap	Handle for removing the filter	Avoid twisting while pulling
Base grille	Covers the lower front area	Stays in place for filter changes

Replacing the filter (important details)

• Turn the filter cap counterclockwise to remove it from the old filter.
• Keep the cap; it is reused on the replacement filter.
• Remove the protective cover from the new filter O-rings.
• Install the cap on the new filter and turn it clockwise until it snaps.
• Push the new filter in until it seats fully.

If you need the correct replacement, this model uses the genuine Kenmore refrigerator water filter EDR3RXD1. You can order it from the parts list for this model, or search by model number on Sears PartsDirect.

Why it matters

Knowing the exact filter location helps prevent cracked caps, leaks at the base grille, and low water flow caused by a filter that is not fully seated.

Last updated: February 2026

Many Kenmore refrigerators are built by Whirlpool; the quickest way to tell is the model number prefix. For Kenmore model 10658142801, the 106 prefix is a Whirlpool-built Kenmore platform, so Whirlpool-style parts and service procedures commonly apply (use the owner's manual for model-specific details).

How to identify the manufacturer from the model number

On Kenmore appliances, the first three digits of the model number are the source code that points to the original manufacturer.

Common Whirlpool-built Kenmore prefixes include:

• 106 (very common on Kenmore refrigerators)
• 110
• 665
• 198
• 552

What this means for parts and repairs

When your Kenmore refrigerator is Whirlpool-built, you will often see Whirlpool-family part IDs and components used across similar designs.

Here are examples of Whirlpool-family parts available for Kenmore 10658142801:

• Water filtration: genuine Kenmore refrigerator water filter EDR3RXD1
• Ice maker assembly: refrigerator ice maker WPW10190961
• Cooling airflow: refrigerator evaporator fan motor WP2315549
• Temperature regulation: refrigerator temperature control WP2315562

Quick examples (this model)

System	Example part you may replace	What it affects
Water/ice	EDR3RXD1 water filter	Water taste, flow, ice quality
Ice maker	WPW10190961 ice maker	Ice production
Cooling	WP2315549 evaporator fan motor	Even temps in fresh food/freezer
Controls	WP2315562 temperature control	Temperature stability

Why it matters

Knowing the manufacturer helps you match the right parts, diagrams, and troubleshooting steps. With a Whirlpool-built Kenmore (like model 10658142801), symptoms such as warm temperatures, no ice, or low water flow often trace to common Whirlpool-style components like the evaporator fan motor, ice maker, or water filter housing.

For model-specific operating features (water filter status light, filtration system, ice maker and storage bin), follow the procedures in the owner's manual.

You can order replacement parts for Kenmore 10658142801 from the parts list for this model, or search by model number on Sears PartsDirect.

Last updated: February 2026

The SY EF code on a Kenmore refrigerator typically points to a cooling-system airflow problem, most often involving the evaporator fan circuit or a freezer temperature sensor (thermistor) signal that the control cannot read correctly. On Kenmore model 10658142801, start with a power reset and then check for fan operation and ice buildup using the owner's manual.

What to check first (fast, no-tools steps)

• Power reset: Unplug the refrigerator (or switch off the breaker) for 5 minutes, then restore power.
• Listen for the evaporator fan: With the freezer door closed (door switch held in), you should typically hear a steady fan sound.
• Look for frost or ice buildup on the freezer back wall; heavy frost often means airflow is blocked.
• Confirm vents are clear: Do not block freezer air returns with packages.
• Verify temperatures: Aim for about 0°F in the freezer and 37°F in the fresh food section.

Common causes and likely fixes

SY EF is usually triggered when the control senses the freezer is not moving cold air correctly or is getting an abnormal sensor reading.

What you notice	Most likely cause	What we recommend
Freezer warm, no fan sound	Evaporator fan not running	Inspect wiring and fan; replace the fan motor if failed (see refrigerator evaporator fan motor WP2315549)
Loud fan noise, then stops	Fan blade hitting ice	Defrost the unit and correct the cause of icing; check the defrost system (see refrigerator bi-metal thermostat WPW10225581)
Ice maker and cooling both act odd	Control issue or sensor signal problem	After reset, inspect connections; if symptoms persist, testing the control may be needed

Why it matters

When the evaporator fan cannot move air across the evaporator, temperatures drift, food can spoil, and the compressor may run longer than normal. Fixing airflow issues early helps protect the sealed system and improves temperature stability.

Parts that commonly relate to SY EF symptoms

• Refrigerator evaporator fan motor WP2315549
• Refrigerator evaporator fan blade WP2169142
• Refrigerator bi-metal thermostat WPW10225581

If you need to order replacement parts for Kenmore 10658142801, use the parts list for this model or search by model number on Sears PartsDirect.

Last updated: February 2026

To find the size of your Kenmore 10658142801 refrigerator, measure the exterior width, height, and depth for fit, then estimate interior capacity in cubic feet using interior measurements. For model-specific installation clearances, use the owner's manual.

Measure exterior dimensions (fit)

Use a tape measure and record inches:

• Width: left to right across the front (include handles only if they affect the opening)
• Height: floor to top of cabinet (include hinge cover if it sits higher)
• Depth: cabinet front to back (also note depth with doors and handles if needed)
• Door swing space: room for doors to open fully

Common clearance guidance for this model

From the manual for this style of Kenmore side-by-side:

• Allow about 1/2 inch on each side and at the top for ventilation
• If next to a fixed wall, allow about 2 inches minimum on the hinge side for door swing
• Leave extra space behind for water line connections if you have an ice maker

Estimate storage capacity (cubic feet)

Measure the interior compartment and calculate:

• Multiply: interior width × interior height × interior depth = cubic inches
• Divide by 1,728 to convert to cubic feet

What you want	Measure	Formula
Exterior size	W, H, D	inches
Capacity	interior W, H, D	(W×H×D) ÷ 1,728

Why it matters

Exterior dimensions prevent delivery and door-swing problems; cubic feet helps compare capacity, but shelves, bins, and an ice maker reduce usable space.

If you are measuring because water and ice components take up room, check your filter setup; the genuine Kenmore refrigerator water filter EDR3RXD1 is a common replacement.

You can order model-specific parts from the parts list for your refrigerator, or search by model number on Sears PartsDirect.

Last updated: February 2026