Kenmore 66513292K110 undercounter dishwasher Parts

Common problems we see on the Kenmore 66513292K110 dishwasher include poor cleaning, not draining, leaks, and control issues (buttons not responding or lights blinking). Many of these are caused by clogs, loading or detergent problems, or a worn component such as a filter, drain pump, or door seal.

• Not cleaning well: clogged filter, blocked spray arm holes, low water temperature, overloading
• Not draining: kinked/blocked drain hose, clogged filter/sump, failed drain pump
• Leaking: door seal wear, lower door seal wear, tub gasket issues, loose hose connections
• Buttons not working / lights blinking: stuck key, moisture in console, wiring or control problem
• Poor drying: no rinse aid, heater issue, cycle selection

• Clean the filter and remove debris from the sump area.
• Spin the spray arms by hand and clear any blocked holes.
• Confirm hot water is reaching the dishwasher (many models perform best around 120°F).
• Check the drain hose routing for kinks and make sure it is looped high under the counter.
• Run a short cycle and listen: drain motor sound but no water movement often indicates a restriction.

Catching a clog or worn seal early helps prevent repeat wash failures, standing water odors, and cabinet or floor damage. It also reduces strain on the pump motor and electronic control.

For model-specific installation and drain routing details, follow the 66513292K110 installation guide.

Last updated: January 2026

On the Kenmore 66513292K110 dishwasher, a red lock (often a padlock icon) typically means Control Lock is turned on, so the buttons will not respond until you turn that feature off. The exact button sequence can vary by console; use the 66513292K110 user manual for the correct steps.

Try these common Control Lock methods used on many Kenmore dishwashers:

• Press and hold Control Lock for about 3 seconds (if your panel has that button).
• Press and hold Heated Dry for about 3 seconds (common on some models).
• Press and hold Air Dry for about 3 seconds (common on some models).
• If the dishwasher is running, press Cancel/Drain to stop the cycle, then try unlocking.
• If the door is slightly open, close it fully and try again; some models will not toggle lock with the door unlatched.

Control Lock is the most common cause, but if the red lock stays on after you try the correct key sequence, check these items:

• Power reset: Turn off the breaker for 1 minute, then restore power.
• Stuck key: Wipe the console and press each key once to ensure none are physically stuck.
• Moisture in the console: Let the door sit open for 30 to 60 minutes to dry the control area.
• Control problem: If the console lights behave erratically, the user interface can be the issue.

If you suspect the console is failing, the compatible control panel component for this model is the dishwasher user interface WPW10333393.

Control Lock helps prevent accidental starts and stops (especially with kids or when wiping the control panel). If it is on, the dishwasher can look “broken” even though it is working normally.

Last updated: January 2026

For Kenmore dishwasher model 66513292K110, the most reliable “hard reset” we can recommend without guessing at console-specific key sequences is a full power reset: turn the circuit breaker OFF for about 5 minutes, then restore power and start a cycle. See the 66513292K110 installation guide for electrical shutoff and safety steps.

• If a cycle is running, press Cancel/Drain if your console has it; otherwise let the unit stop.
• Turn OFF power at the circuit breaker (preferred over unplugging).
• Wait 5 minutes so the control can fully power down.
• Turn the breaker ON.
• Start the shortest wash cycle and confirm it fills, washes, and drains.

We cannot confirm a specific keypad sequence for 66513292K110 using the model’s available installation documentation; keypad layouts and service sequences can vary by console revision.

What we can confirm from the installation instructions:

• The dishwasher uses a 120-volt, 60 Hz, 15- or 20-amp supply.
• If the dishwasher does not operate, initial checks include breaker/fuse, door latch/closure, cycle selection, and water supply.
• The Start/Resume light may flash if the door is not closed within 3 seconds after pressing Start/Resume.

• Verify the door is fully closed and latched
• Confirm the breaker is on and the outlet has power
• Make sure the water shutoff valve under the sink is open
• Check for a kinked or improperly routed drain hose

If troubleshooting points to a failed component, these are compatible examples for this model:

• Dishwasher water inlet valve W11175771 (fill problems)
• Dishwasher drain pump WPW10348269 (drain problems)

A true hard reset clears temporary control glitches. If the same symptom returns right away, it usually points to an underlying issue such as power supply, door closure, water supply, or a failing component.

Last updated: January 2026